Baum Bros. Imports 26.4 manual Quantity liters 22,5, Lubrication intervals weekly

Page 101

HYDRAULIC

We recommend to have oil changed and unit checked by BAUM and/or authorized personnel.

Attention when bleeding hot oil - danger of burning!

Oil change:	approx. every 6000 hrs.
	Fill in oil up to middle of oil level indicator!
	Quantity (liters): 22,5

BACKGAUGE DRIVE (grease lubrication)

Usable oil brands (DIN 51524, in alphabetical order):

ARAL Vitam GF 46

AGIP Oso 46

BP Energol HLP-HM 46

CASTROL Hyspin SP 46

DEA Astron HLP 46

ESSO Nuto H 46

ELF Elfolna 46

FINA Hydran AF 46

FUCHS Renolin B, rot

KLÜBER Lamora HLP 46

MOBIL DTE 25

OPTIMOL Hydo 46 or Hydo MV 32

SHELL Tellus C 46

TOTAL Azolla ZS 467

Usable grease brands (DIN 51825, in alphabetical order):

Lubrication by grease gun!

1.Move backgauge to position 42 cm (16,5 inches)!

2.Remove lid (C) at backgauge drive guard

3.Grease spindle via lubricating nipple

2 - 3 strokes with the grease gun are sufficient.

Lubrication intervals: monthly

GUIDINGS FOR KNIFE AND CLAMP (grease lubrication)

Lubrication by grease gun!

1.Lubricate guidings for knife bar (A) from the front side: 2 lubricating nipples at the front plate

2.Lubricate clamp guidings from the rear side (B): 2 lubricating nipples

2 - 3 strokes with the grease gun are sufficient.

Lubrication intervals: weekly

ARAL Radlagerfett AGIP Autol Top 2000 or Longtime Grease 2 BP Energrease LS 2 DEA Paragon EP 2

ESSO Unirex N2 or Essonorva 275 FINA Pluton AX 2

KLÜBER Centoplex 2 EP MOBIL Mobilgrease XHP 222 OPTIMOL Longtime PD 2 SHELL Retinax LX 2 TOTAL Multis EP 2

A

B

C

i

x

PROGRAMMABLE

K8 - 3

Image 101

Contents Baumcut 26.4 Programmable K5B IndexK5A Index MaintenanceK5C K5DControl Panel / Operating Elements ProgrammableExplanation of Pictographs on the Display Chapter Survey Chapter SurveyCopyright IntroductionPlease pay special attention to the following information Page Page Machine Layout Plan Dimensions in mmPlace of Installation Transport and Installation of the MachineAfter the Installation of the Machine Case of ComplaintsEnergy lead wire Power SupplyType plate Type Plates Type plateWorking Area of Operating Personnel Safety Relevant Machine ElementsSafety Auxiliary Tools Placement of the warning labels Label 1 Label 2 Label 3 Placement of the warning label DurabilitySafety Signs / Warning Signs Safety SignsSafety Precautions Technical DataPermissible Environmental and Operating Conditions Hydraulic DataVoltage supply single phase AC 210 240, 60Hz Voltage supply 3 phase 360 420V, 50/60HzVoltage supply single phase AC 200 240, 50Hz Page Safety Symbol Page Electrical energy Start Up To prevent a start-up of the machine Switching Machine onTurning Machine OFF Program Data Display Measurement Display and Measurement SystemPage Manual Operation Cutting Line Indicator, Mechanical with Clamp Setting of Measurements Backgauge Movement by HandCutting Line Indicator, Optical Actuate toggle switch 8 at main switch plateClamping and Cutting Clamp Pressure AdjustmentSetting the Clamping Time To continue the cutting process Light BarrierInterference into the light curtain causes Meaning of LEDs in display unit Continuation Light BarrierD2 D4 D1 D3 Removing of false clamp plate Clamping with False Clamp PlateAttaching false clamp plate Automatic Operation Functions of the menu keys Key Main menu Function Survey Basic Display Program Data Basic DisplaysProgram Data Key Main Menu Function Survey Program Information Key Program DirectoryContin. Basic Display Program Data Press key Basic Display Program Information1575 Basic Display Program Directory5VAC Other input modes in this displayPress menu key Basic Display Main Menu Function SurveyCursor Movement in Basic Display Measurement input in inches Automatic Backgauge Adjustment through Numerical KeyboardProgram data display After 1. inputinput section shows Backgauge movesDeletion of a Wrong Input Input Error Value of Nom. Backgauge Position too Low/HighMoving Backgauge to a Nominal Position Positioning Deletion of a wrong inputDisplay example Possible in all 4 basic monitor displaysMake selection Program Number Example Selecting a ProgramAccording to order number Numerical keyboard Continuing Selecting a ProgramOnly in Program data display Storage of MeasurementsTwo side trim on size DIN A3 Untrimmed size 31 x 43 cm Setting Up a Cutting Program, ExampleKey input Running the programCall program 5A Enter Correcting after storing Correction of an Input ErrorCorrecting before storing Automatic OFF Automatic ON/OFFPositioning check in automatic operation Made GO to PositionAfter cut Example Setting a cutting program, exampleRunning a Cutting Program Press key Program Information Storing of Program InformationsStoring Order End of information inputDeletion of a Step Number Deletion of One/Several Programs Deletion of Complete Memory PROStoring of Measurements According to Printed Image Inserting of Measurements into a ProgramCalculator Functions Overflow IndicatorConditionsAutomatic OFF To set backgauge to a calculated sizeNegative Sign Using Backgauge Position of CalculationsSwitching the function off Additional Functions Machine Functions and Additional Functions Menu KeysMachine Functions Key Main Menu Key Main Menu includes the following functions Machine Function Main Menu Function SurveySelect Language / Measuring Unit ServiceSelect Main Menu Funtion survey Select function Language or Measuring UnitCalibration to compensate for knifes of different thickness Knife CompensationSelect function Select Knife compensation Knife changeResting Time for Knife at BDC Adjust timeSet counter Maintenance Cut CounterCalculate basic position Preset FunctionsSelection of Main Menu Correction of Current Position Select function Preset functions Scan Reference Positionj Continuing Preset FunctionsPossible funtions in Auxiliary mode Abortion of reference runEnd of input with key Adjustment of Display ContrastBlock Programming Possibility of edge trim preadjustingExample Variation 1, selection 1 Angular cut Setting up a Block ProgrammingDeletion of an input parameter with Block Programming Selection of an input parameter with Block ProgrammingCorrection of an input parameter with Block Programming Four trim cut Example Variation 1, selection Four trim cutEnter Edge trim Four trim cut with labels Example Variation 3, selection 3 Four trim cut with labelsBlock Programming Four-side trim with labels and trim cuts Right-hand lay side Enter trimout measurement Enter outside trimBlock Programming Menu Key Additional Functions Erase Additional Function Storage of Additional Functions with Cut SizeSubsequent Storing of Additional Functions Ejector OFF List of Additional FunctionsAdditional function Jogging mark Operation K5C Menu Key Auxiliary Functions After program generation Cut and RecordSheet Size Tables Graphics OFF Subtraction Repetition UnitQuitt the function K5D Menu Key Machine Parameters Adjustment of BDC time Adjustment of pre-pressure timePrepressure Time Make selectionKnife Change Deposit knife in knife box!! Remove knife guard Mounting the knife Knife ChangeKnife adjustment Adjustment of knife pre-tensionAdjusting the knife Tighten up all knife boltsRemoving of cutting stick Changing of cutting stickInserting of cutting stick Normal Turn overPage Malfunctions / Breakdowns Remedy for machine malfunctions Electrical Malfunctions/BreakdownsMachine functions possible in Auxiliary Mode Start Up Breakdown Scan Reference Point/Auxiliary ModeKnife bar or clamp not in top dead centre Breakdown Knife bar stops beneath the upper dead centreBreakdown Clamp stops beneath the upper dead centre Maintenance Basic information about servicing and maintenance work Lubrication intervals weekly Quantity liters 22,5Hrs. per day equal Cleaning of DisplayPage Baum USA Service Mr./MrsFax 937/492-7280