Baum Bros. Imports 26.4 manual Technical Data, Permissible Environmental and Operating Conditions

Page 18

1.0 Technical Data/Machine Layout/Transport and Installation of Machine/Safety Relevant Machine Elements

Technical Data

Permissible Environmental and Operating Conditions

Operate the machine in closed areas, exclusively!

Air humidity:	35% - 95% (non condensing)
Ambient air temperature:	+5°C - +40°C

Hydraulic Data

Hydraulic pressure, max.:

160 bars!

Safety Precautions

•Minimum age of operating staff: 18 years!

•Before starting any work at the machine - read safety section of manual!

•During the working process no other persons must enter the working area or interfere with the process

•Use the angle included in the scope of supply for positioning the cutting material

•Knife change may only be carried out by personnel especially trained for this purpose

•Utmost care must be taken when handling the knife!! Always deposit or transport the knife in the knife case.

•Use only undamaged and sharp knives!

•During the cutting no tool or objects - such as e.g. T-wrench must be on the

machine table in order to prevent them from reaching unintentionally under the clamp and/or knife during the cutting process. There is a high risk of injuries due to little parts of the knife edge coming off in splinters.

•Observe the procedures described in case of malfunctions and the mainte nance intervals indicated.

Residual Risk

In spite of the safety measures provided by construction there remains a residual risk when operating the machine.

This residual risk mainly concerns the danger of contusions and cuts during clamping, cutting or knife change as well as handling the cutting material in general, if the necessary care is neglected.

The parts especially affected are the upper extremities of the operating staff - especially their arms and hands.

Special care must be taken when performing the knife change. It may only be carried out by personnel especially trained for this job!

During knife change no other persons must enter the working area of the machine (cuts)!

K1 - 10

Image 18

Contents Baumcut 26.4 Programmable Index K5AK5B K5C MaintenanceIndex K5DProgrammable Control Panel / Operating ElementsExplanation of Pictographs on the Display Chapter Survey Chapter SurveyIntroduction Please pay special attention to the following informationCopyright Page Page Machine Layout Dimensions in mm PlanAfter the Installation of the Machine Transport and Installation of the MachinePlace of Installation Case of ComplaintsPower Supply Energy lead wireType Plates Type plate Type plateSafety Relevant Machine Elements Safety Auxiliary ToolsWorking Area of Operating Personnel Placement of the warning label Durability Placement of the warning labels Label 1 Label 2 Label 3Safety Signs Safety Signs / Warning SignsPermissible Environmental and Operating Conditions Technical DataSafety Precautions Hydraulic DataVoltage supply 3 phase 360 420V, 50/60Hz Voltage supply single phase AC 200 240, 50HzVoltage supply single phase AC 210 240, 60Hz Page Safety Symbol Page Electrical energy Start Up Switching Machine on Turning Machine OFFTo prevent a start-up of the machine Measurement Display and Measurement System Program Data DisplayPage Manual Operation Cutting Line Indicator, Optical Setting of Measurements Backgauge Movement by HandCutting Line Indicator, Mechanical with Clamp Actuate toggle switch 8 at main switch plateClamp Pressure Adjustment Setting the Clamping TimeClamping and Cutting Light Barrier Interference into the light curtain causesTo continue the cutting process Continuation Light Barrier D2 D4 D1 D3Meaning of LEDs in display unit Clamping with False Clamp Plate Attaching false clamp plateRemoving of false clamp plate Automatic Operation Functions of the menu keys Key Main menu Function Survey Program Data Key Main Menu Function Survey Basic DisplaysBasic Display Program Data Program Information Key Program DirectoryContin. Basic Display Program Data Basic Display Program Information Press key5VAC Basic Display Program Directory1575 Other input modes in this displayBasic Display Main Menu Function Survey Press menu keyCursor Movement in Basic Display Program data display After 1. inputinput section shows Automatic Backgauge Adjustment through Numerical KeyboardMeasurement input in inches Backgauge movesMoving Backgauge to a Nominal Position Positioning Input Error Value of Nom. Backgauge Position too Low/HighDeletion of a Wrong Input Deletion of a wrong inputPossible in all 4 basic monitor displays Make selection Program NumberDisplay example Selecting a Program According to order numberExample Continuing Selecting a Program Numerical keyboardStorage of Measurements Only in Program data displayKey input Setting Up a Cutting Program, ExampleTwo side trim on size DIN A3 Untrimmed size 31 x 43 cm Running the programCall program 5A Enter Correction of an Input Error Correcting before storingCorrecting after storing Positioning check in automatic operation Automatic ON/OFFAutomatic OFF Made GO to PositionExample Setting a cutting program, example Running a Cutting ProgramAfter cut Storing Order Storing of Program InformationsPress key Program Information End of information inputDeletion of a Step Number Deletion of One/Several Programs PRO Deletion of Complete MemoryInserting of Measurements into a Program Storing of Measurements According to Printed ImageConditionsAutomatic OFF Overflow IndicatorCalculator Functions To set backgauge to a calculated sizeUsing Backgauge Position of Calculations Switching the function offNegative Sign Machine Functions and Additional Functions Menu Keys Machine FunctionsAdditional Functions Machine Function Main Menu Function Survey Key Main Menu Key Main Menu includes the following functionsSelect Main Menu Funtion survey ServiceSelect Language / Measuring Unit Select function Language or Measuring UnitSelect function Select Knife compensation Knife CompensationCalibration to compensate for knifes of different thickness Knife changeAdjust time Resting Time for Knife at BDCMaintenance Cut Counter Set counterPreset Functions Selection of Main Menu Correction of Current PositionCalculate basic position Possible funtions in Auxiliary mode Continuing Preset FunctionsSelect function Preset functions Scan Reference Positionj Abortion of reference runAdjustment of Display Contrast End of input with keyPossibility of edge trim preadjusting Block ProgrammingSetting up a Block Programming Example Variation 1, selection 1 Angular cutSelection of an input parameter with Block Programming Correction of an input parameter with Block ProgrammingDeletion of an input parameter with Block Programming Example Variation 1, selection Four trim cut Enter Edge trimFour trim cut Example Variation 3, selection 3 Four trim cut with labels Four trim cut with labelsBlock Programming Four-side trim with labels and trim cuts Right-hand lay side Enter outside trim Enter trimout measurementBlock Programming Menu Key Additional Functions Storage of Additional Functions with Cut Size Subsequent Storing of Additional FunctionsErase Additional Function List of Additional Functions Additional function Jogging mark OperationEjector OFF K5C Menu Key Auxiliary Functions Cut and Record Sheet Size TablesAfter program generation Subtraction Repetition Unit Quitt the functionGraphics OFF K5D Menu Key Machine Parameters Prepressure Time Adjustment of pre-pressure timeAdjustment of BDC time Make selectionKnife Change Deposit knife in knife box!! Remove knife guard Knife Change Mounting the knifeAdjusting the knife Adjustment of knife pre-tensionKnife adjustment Tighten up all knife boltsInserting of cutting stick Changing of cutting stickRemoving of cutting stick Normal Turn overPage Malfunctions / Breakdowns Electrical Malfunctions/Breakdowns Remedy for machine malfunctionsStart Up Breakdown Scan Reference Point/Auxiliary Mode Machine functions possible in Auxiliary ModeBreakdown Knife bar stops beneath the upper dead centre Breakdown Clamp stops beneath the upper dead centreKnife bar or clamp not in top dead centre Maintenance Basic information about servicing and maintenance work Quantity liters 22,5 Lubrication intervals weeklyCleaning of Display Hrs. per day equalPage Service Mr./Mrs Fax 937/492-7280Baum USA