Baum Bros. Imports 26.4 manual Continuing Preset Functions, Abortion of reference run

Page 68

5.0 Automatic Operation

Continuing: Preset Functions

Select function "Preset functions":

Scan Reference Positionj

In the case of a machine malfunction the reference point can be newly scanned with this function.

Procedure:
1.	Select "Scan reference position"	< display change >
2.	Confirm "Clear table surface"	< display change >

3.Start backgauge run: Actuate electronical handweel in forward or reverse operation

Abortion of reference run:

Press key

As soon as the reference run has been terminated, the menu "Correct. current position" is displayed.

The displayed basic measurement must be confirmed (see page K5B - 7). After this procedure the Program Data display will automatically be indicated.

Auxiliary operation

If no reference point is found during the reference run an auxiliary mode must be activated (see page K7 - 3)

Possible funtions in Auxiliary mode:

•cutting

•manual displacement of backgauge by means of of electronic handwheel

K5B - 8

Image 68

Contents Baumcut 26.4 Programmable K5B IndexK5A Maintenance IndexK5C K5DProgrammable Control Panel / Operating ElementsExplanation of Pictographs on the Display Chapter Survey Chapter SurveyCopyright IntroductionPlease pay special attention to the following information Page Page Machine Layout Dimensions in mm PlanTransport and Installation of the Machine Place of InstallationAfter the Installation of the Machine Case of ComplaintsPower Supply Energy lead wireType Plates Type plate Type plateWorking Area of Operating Personnel Safety Relevant Machine ElementsSafety Auxiliary Tools Placement of the warning label Durability Placement of the warning labels Label 1 Label 2 Label 3Safety Signs Safety Signs / Warning SignsTechnical Data Safety PrecautionsPermissible Environmental and Operating Conditions Hydraulic DataVoltage supply single phase AC 210 240, 60Hz Voltage supply 3 phase 360 420V, 50/60HzVoltage supply single phase AC 200 240, 50Hz Page Safety Symbol Page Electrical energy Start Up To prevent a start-up of the machine Switching Machine onTurning Machine OFF Measurement Display and Measurement System Program Data DisplayPage Manual Operation Setting of Measurements Backgauge Movement by Hand Cutting Line Indicator, Mechanical with ClampCutting Line Indicator, Optical Actuate toggle switch 8 at main switch plateClamping and Cutting Clamp Pressure AdjustmentSetting the Clamping Time To continue the cutting process Light BarrierInterference into the light curtain causes Meaning of LEDs in display unit Continuation Light BarrierD2 D4 D1 D3 Removing of false clamp plate Clamping with False Clamp PlateAttaching false clamp plate Automatic Operation Functions of the menu keys Key Main menu Function Survey Basic Displays Basic Display Program DataProgram Data Key Main Menu Function Survey Program Information Key Program DirectoryContin. Basic Display Program Data Basic Display Program Information Press keyBasic Display Program Directory 15755VAC Other input modes in this displayBasic Display Main Menu Function Survey Press menu keyCursor Movement in Basic Display Automatic Backgauge Adjustment through Numerical Keyboard Measurement input in inchesProgram data display After 1. inputinput section shows Backgauge movesInput Error Value of Nom. Backgauge Position too Low/High Deletion of a Wrong InputMoving Backgauge to a Nominal Position Positioning Deletion of a wrong inputDisplay example Possible in all 4 basic monitor displaysMake selection Program Number Example Selecting a ProgramAccording to order number Continuing Selecting a Program Numerical keyboardStorage of Measurements Only in Program data displaySetting Up a Cutting Program, Example Two side trim on size DIN A3 Untrimmed size 31 x 43 cmKey input Running the programCall program 5A Enter Correcting after storing Correction of an Input ErrorCorrecting before storing Automatic ON/OFF Automatic OFFPositioning check in automatic operation Made GO to PositionAfter cut Example Setting a cutting program, exampleRunning a Cutting Program Storing of Program Informations Press key Program InformationStoring Order End of information inputDeletion of a Step Number Deletion of One/Several Programs PRO Deletion of Complete MemoryInserting of Measurements into a Program Storing of Measurements According to Printed ImageOverflow Indicator Calculator FunctionsConditionsAutomatic OFF To set backgauge to a calculated sizeNegative Sign Using Backgauge Position of CalculationsSwitching the function off Additional Functions Machine Functions and Additional Functions Menu KeysMachine Functions Machine Function Main Menu Function Survey Key Main Menu Key Main Menu includes the following functionsService Select Language / Measuring UnitSelect Main Menu Funtion survey Select function Language or Measuring UnitKnife Compensation Calibration to compensate for knifes of different thicknessSelect function Select Knife compensation Knife changeAdjust time Resting Time for Knife at BDCMaintenance Cut Counter Set counterCalculate basic position Preset FunctionsSelection of Main Menu Correction of Current Position Continuing Preset Functions Select function Preset functions Scan Reference PositionjPossible funtions in Auxiliary mode Abortion of reference runAdjustment of Display Contrast End of input with keyPossibility of edge trim preadjusting Block ProgrammingSetting up a Block Programming Example Variation 1, selection 1 Angular cutDeletion of an input parameter with Block Programming Selection of an input parameter with Block ProgrammingCorrection of an input parameter with Block Programming Four trim cut Example Variation 1, selection Four trim cutEnter Edge trim Example Variation 3, selection 3 Four trim cut with labels Four trim cut with labelsBlock Programming Four-side trim with labels and trim cuts Right-hand lay side Enter outside trim Enter trimout measurementBlock Programming Menu Key Additional Functions Erase Additional Function Storage of Additional Functions with Cut SizeSubsequent Storing of Additional Functions Ejector OFF List of Additional FunctionsAdditional function Jogging mark Operation K5C Menu Key Auxiliary Functions After program generation Cut and RecordSheet Size Tables Graphics OFF Subtraction Repetition UnitQuitt the function K5D Menu Key Machine Parameters Adjustment of pre-pressure time Adjustment of BDC timePrepressure Time Make selectionKnife Change Deposit knife in knife box!! Remove knife guard Knife Change Mounting the knifeAdjustment of knife pre-tension Knife adjustmentAdjusting the knife Tighten up all knife boltsChanging of cutting stick Removing of cutting stickInserting of cutting stick Normal Turn overPage Malfunctions / Breakdowns Electrical Malfunctions/Breakdowns Remedy for machine malfunctionsStart Up Breakdown Scan Reference Point/Auxiliary Mode Machine functions possible in Auxiliary ModeKnife bar or clamp not in top dead centre Breakdown Knife bar stops beneath the upper dead centreBreakdown Clamp stops beneath the upper dead centre Maintenance Basic information about servicing and maintenance work Quantity liters 22,5 Lubrication intervals weeklyCleaning of Display Hrs. per day equalPage Baum USA Service Mr./MrsFax 937/492-7280