Baum Bros. Imports 26.4 manual Selection of an input parameter with Block Programming

Page 72

5.0 Automatic Operation

Block Programming

Confirm the sheet orientation or turn sheet orientation (observe paper grain)

Menu:	1 Sheet orient. OK
	2 Turn sheet

8.e.g.: "Sheet orient. OK"

Enter Edge trim

9.Enter "Edge trim width X", confirm with key

10.Enter "Edge trim width Y", confirm with key

11.Finish entry with key "Enter"

< Program data display appears with a graphic window of the current Block Programming variation (visible sheet orientation with order start), see also page K5D - 3 "Graphics OFF" >

Selection of an input parameter with Block Programming

Actuate cursor keys (browse) until desired parameter appears

Correction of an input parameter with Block Programming

1.Select parameter with cursor keys

2.Enter new parameter (old parameter is erased)

3.Press key

Attention! Function "Help":

Explanation of pictographs and description of functions

Deletion of an input parameter with Block Programming

1.Enter Block Programming (initial fig.)

2.Press key "Delete"

K5B - 12

Image 72

Contents Baumcut 26.4 Programmable Index K5AK5B Maintenance IndexK5C K5DProgrammable Control Panel / Operating ElementsExplanation of Pictographs on the Display Chapter Survey Chapter SurveyIntroduction Please pay special attention to the following informationCopyright Page Page Machine Layout Dimensions in mm PlanTransport and Installation of the Machine Place of InstallationAfter the Installation of the Machine Case of ComplaintsPower Supply Energy lead wireType Plates Type plate Type plateSafety Relevant Machine Elements Safety Auxiliary ToolsWorking Area of Operating Personnel Placement of the warning label Durability Placement of the warning labels Label 1 Label 2 Label 3Safety Signs Safety Signs / Warning SignsTechnical Data Safety PrecautionsPermissible Environmental and Operating Conditions Hydraulic DataVoltage supply 3 phase 360 420V, 50/60Hz Voltage supply single phase AC 200 240, 50HzVoltage supply single phase AC 210 240, 60Hz Page Safety Symbol Page Electrical energy Start Up Switching Machine on Turning Machine OFFTo prevent a start-up of the machine Measurement Display and Measurement System Program Data DisplayPage Manual Operation Setting of Measurements Backgauge Movement by Hand Cutting Line Indicator, Mechanical with ClampCutting Line Indicator, Optical Actuate toggle switch 8 at main switch plateClamp Pressure Adjustment Setting the Clamping TimeClamping and Cutting Light Barrier Interference into the light curtain causesTo continue the cutting process Continuation Light Barrier D2 D4 D1 D3Meaning of LEDs in display unit Clamping with False Clamp Plate Attaching false clamp plateRemoving of false clamp plate Automatic Operation Functions of the menu keys Key Main menu Function Survey Basic Displays Basic Display Program DataProgram Data Key Main Menu Function Survey Program Information Key Program DirectoryContin. Basic Display Program Data Basic Display Program Information Press keyBasic Display Program Directory 15755VAC Other input modes in this displayBasic Display Main Menu Function Survey Press menu keyCursor Movement in Basic Display Automatic Backgauge Adjustment through Numerical Keyboard Measurement input in inchesProgram data display After 1. inputinput section shows Backgauge movesInput Error Value of Nom. Backgauge Position too Low/High Deletion of a Wrong InputMoving Backgauge to a Nominal Position Positioning Deletion of a wrong inputPossible in all 4 basic monitor displays Make selection Program NumberDisplay example Selecting a Program According to order numberExample Continuing Selecting a Program Numerical keyboardStorage of Measurements Only in Program data displaySetting Up a Cutting Program, Example Two side trim on size DIN A3 Untrimmed size 31 x 43 cmKey input Running the programCall program 5A Enter Correction of an Input Error Correcting before storingCorrecting after storing Automatic ON/OFF Automatic OFFPositioning check in automatic operation Made GO to PositionExample Setting a cutting program, example Running a Cutting ProgramAfter cut Storing of Program Informations Press key Program InformationStoring Order End of information inputDeletion of a Step Number Deletion of One/Several Programs PRO Deletion of Complete MemoryInserting of Measurements into a Program Storing of Measurements According to Printed ImageOverflow Indicator Calculator FunctionsConditionsAutomatic OFF To set backgauge to a calculated sizeUsing Backgauge Position of Calculations Switching the function offNegative Sign Machine Functions and Additional Functions Menu Keys Machine FunctionsAdditional Functions Machine Function Main Menu Function Survey Key Main Menu Key Main Menu includes the following functionsService Select Language / Measuring UnitSelect Main Menu Funtion survey Select function Language or Measuring UnitKnife Compensation Calibration to compensate for knifes of different thicknessSelect function Select Knife compensation Knife changeAdjust time Resting Time for Knife at BDCMaintenance Cut Counter Set counterPreset Functions Selection of Main Menu Correction of Current PositionCalculate basic position Continuing Preset Functions Select function Preset functions Scan Reference PositionjPossible funtions in Auxiliary mode Abortion of reference runAdjustment of Display Contrast End of input with keyPossibility of edge trim preadjusting Block ProgrammingSetting up a Block Programming Example Variation 1, selection 1 Angular cutSelection of an input parameter with Block Programming Correction of an input parameter with Block ProgrammingDeletion of an input parameter with Block Programming Example Variation 1, selection Four trim cut Enter Edge trimFour trim cut Example Variation 3, selection 3 Four trim cut with labels Four trim cut with labelsBlock Programming Four-side trim with labels and trim cuts Right-hand lay side Enter outside trim Enter trimout measurementBlock Programming Menu Key Additional Functions Storage of Additional Functions with Cut Size Subsequent Storing of Additional FunctionsErase Additional Function List of Additional Functions Additional function Jogging mark OperationEjector OFF K5C Menu Key Auxiliary Functions Cut and Record Sheet Size TablesAfter program generation Subtraction Repetition Unit Quitt the functionGraphics OFF K5D Menu Key Machine Parameters Adjustment of pre-pressure time Adjustment of BDC timePrepressure Time Make selectionKnife Change Deposit knife in knife box!! Remove knife guard Knife Change Mounting the knifeAdjustment of knife pre-tension Knife adjustmentAdjusting the knife Tighten up all knife boltsChanging of cutting stick Removing of cutting stickInserting of cutting stick Normal Turn overPage Malfunctions / Breakdowns Electrical Malfunctions/Breakdowns Remedy for machine malfunctionsStart Up Breakdown Scan Reference Point/Auxiliary Mode Machine functions possible in Auxiliary ModeBreakdown Knife bar stops beneath the upper dead centre Breakdown Clamp stops beneath the upper dead centreKnife bar or clamp not in top dead centre Maintenance Basic information about servicing and maintenance work Quantity liters 22,5 Lubrication intervals weeklyCleaning of Display Hrs. per day equalPage Service Mr./Mrs Fax 937/492-7280Baum USA