Bosch Power Tools 1671B Plunge Cuts, Cutting Large Sheets, Desired Width CUT RIP Board Guide

Page 13

BM 2610945718 12-06 12/12/06 12:21 PM Page 13

PLUNGE CUTS

Disconnect battery pack from tool before making adjustments. Set depth adjustment according to material to be cut. Tilt saw forward with cutting guide notch lined up with the line you’ve drawn. Raise the lower guard, using lift lever and hold the saw by the front and rear handles (Fig. 10).

With the blade just clearing the material to be cut, start the motor. Gradually lower the back end of saw using the front end of the foot as the hinge point. WARNING: As blade starts cutting the material, release the lower guard immediately. When the foot rests flat on the surface being cut, proceed cutting in forward direction to end of cut. WARNING:

Allow blade to come to a complete stop before lifting the saw from cut. Also, never pull the saw backward since blade will climb out of the material and KICKBACK will occur. Turn saw around and finish the cut in the normal manner, sawing forward. If corners of your pocket cut are not completely cut through, use a jigsaw or hand saw to finish the corners.

CUTTING LARGE SHEETS

Large sheets and long boards sag or bend, depending on support. If you attempt to cut without leveling and properly supporting the piece, the blade will tend to bind, causing KICK-BACK and extra load on the motor (Fig. 11).

Support the panel or board close to the cut, as shown in (Fig. 12). Be sure to set the depth of the cut so that you cut through the sheet or board only and not the table or work bench. The two-by-fours used to raise and support the work should be positioned so that the broadest sides support the work and rest on the table or bench. Do not support the work with the narrow sides as this is an unsteady arrangement. If the sheet or board to be cut is too large for a table or work bench, use the supporting two-by-fours on the floor and secure.

FIG. 11

WRONG

FIG. 10

FOOT

LOWER

GUARD

LIFT

LEVER

FIG. 12

RIGHT

RIP CUTS

The combination blade provided with your saw is for both cross cuts and rip cuts. Ripping is cutting lengthwise with the grain of the wood. Rip cuts are easy to do with a rip fence (Fig. 13). To attach fence, insert fence through slots in foot to desired width as shown and secure with the knob.

FIG. 13

DESIRED

WIDTH

OF CUT

RIP BOARD GUIDE

When rip cutting large sheets, the rip fence may not allow the desired width of cut. Clamp or nail a straight piece of 1" (25 mm) lumber to the sheet as a guide (Fig. 14). Use the right side of the foot against the board guide.

FIG. 14

DESIRED

LINE

OF CUT

KNOB RIP FENCE

RIP BOARD

GUIDE

-13-

Image 13
Contents Read Before Using Work area safety General Safety RulesElectrical safety Personal safetyBattery tool use and care Power tool use and careService Power tools are dangerous in the hands of untrained usersCutting procedures Safety Rules for Circular SawsKickback and related warnings Keep hands away from Danger cutting area and bladeLower guard function Battery Care Battery/ChargerExplode LITHIUM-ION Batteries Battery DisposalSymbols Lift Lever Foot SAW HookButton Lock Button VentilationAttaching the Blade AssemblyVARI-TORQUE Clutch Mark Outer Wrenchwasher Outer WasherSafety Switch Depth Bracket Adjustment Lever ONE Tooth Length shouldSafety Switch Release Button Cutting Angle Check Operating InstructionsVertical Cuts Bevel Cuts Switch Bevel Adjustment Knob Line GuideBrake General CutsCutting Large Sheets Plunge CutsWrong Foot Lower Guard Lift Lever Right RIP Cuts Desired Width CUT RIP Board GuideGreen Indicator Lights RED Button Battery Charged Condition IndicatorTemperature Indicator Light Inserting and Releasing Battery PackBattery Pack RED Light Charger Green Light Charging Battery Pack BC830 1 Hour ChargerImportant Charging Notes Accessories MaintenanceCleaning Sécurité du lieu de travail Consignes générales de sécuritéSécurité électrique Sécurité personnelleUtilisation et entretien des outils à piles Utilisation et entretien des outils ÉlectroportatifsEntretien Procédures de coupe Consignes de sécurité pour scies circulairesAvertissements relatifs aux rebonds et Problèmes associés Le plomb provenant des peintures à base de plomb Fonction du garde inférieurEntretien des piles Chargeur de pileNe tentez pas de Mise au rebut des pilesPiles LITHIUM-ION Symboles Scies circulaires sans fil Description fonctionnelle et spécificationsMontage DE LA Lame AssemblageEmbrayage « VARI-TORQUE » Graduation Rondelle CléextérieureRéglage DE LA Profondeur DE Coupe Consignes de fonctionnementBouton DE Vérification DE L’ANGLE DE CoupeGuide D’ALIGNEMENT Réglage DE LA Coupe EN BiseauCoupes InterrupteurCoupe DE Grandes Feuilles Coupes EN GuichetPlacez le panneau ou la planche sur des supports situés Coupes DE RefenteTémoin DE Pile Chargée Témoins DE CHARGE, Symboles ET SignificationTémoins Verts Bouton Témoin DE TempératureChargement DU BLOC-PILES Chargeur DE 1 Heure BC830 Remarques Importantes Concernant LA ChargeBLOC-PILES Voyant Rouge Chargeur Vert Entretien AccessoiresNettoyage Seguridad del área de trabajo Normas generales de seguridadSeguridad eléctrica Seguridad personalUso y cuidado de las herramientas Alimentadas por baterías MecánicasServicio de ajustes y reparaciones Procedimientos de corte Normas de seguridad para sierras circularesEl retroceso y advertencias relacionadas Función del protector inferior Cuidado de las baterías Batería/cargadorBaterías DE Iones DE Litio Eliminación de las bateríasCon aislamiento doble SímbolosDe Li-ion Sierras circulares sin cordón Descripción funcional y especificacionesColocacion DE LA Hoja EnsamblajeEmbrague DE PAR Motor Variable Marca Arandela LlaveexteriorAjuste DE Profundidad Instrucciones de funcionamientoInterruptor DE Sequridad GatilloCuadrante Pomo DE Ajuste DE Inclinacion Guía DE Línea Ajuste DE InclinacionCortes Verticales Inclinados Guia DE InterruptorCorte DE Planchas Grandes Cortes POR PenetraciónIncorrecto Cortes AL HiloLuces Indicadoras Verdes Boton Indicador DE Estado DE Carga DE LA BateríaLUZ Indicadora DE LA Temperatura Introducción Y Suelta DEL Paquete DE BateríasCarga DEL Paquete DE Baterías Cargador DE 1 Hora BC830 Notas Importantes Para CargarPaquete DE Baterías LUZ Roja Cargador Verde Accesorios MantenimientoServicio LimpiezaRemarques Notas Limited Warranty of Bosch Portable and Benchtop Power Tools