Stow cs403030, cs403026, cs 403016, cs403020 operation manual Silicosis Warning

Page 3

WARNING

SILICOSIS WARNING

Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis. In addition, California and some other authorities have listed respirable crystalline silica as a substance known to cause cancer. When cutting such materials, always follow the respiratory precautions mentioned above.

WARNING

RESPIRATORY HAZARDS

Grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as respiratory disease, cancer, birth defects or other reproductive harm. If you are unfamiliar with the risks associated with the particular process and/or material being cut or the composition of the tool being used, review the material safety data sheet and/or consult your employer, the material manufacturer/supplier, governmental agencies such as OSHA and NIOSH and other sources on hazardous materials. California and some other authorities, for instance, have published lists of substances known to cause cancer, reproductive toxicity, or other harmful effects.

Control dust, mist and fumes at the source where possible. In this regard use good work practices and follow the recommendations of the manufacturers or suppliers, OSHA/NIOSH, and occupational and trade associations. Water should be used for dust suppression when wet cutting is feasible. When the hazards from inhalation of dust, mists and fumes cannot be eliminated, the operator and any bystanders should always wear a respirator approved by NIOSH/MSHA for the materials being used.

Image 3
Contents Models Page Silicosis Warning Stow CS4030 SAW Table of Contents Chassis & Dimensions Sideview Stow CS4030 SAW DimensionsStow CS4030 SAW Specifications Blade Shaft AssemblyOil bath design, fully enclosed cast iron housing Automatic actuating parking brake Wheels Rear Stow CS4030 SAW Engine SpecificationsUncrated Weight Crated WeightTraining Checklist Training ChecklistDaily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistSafety Message Alert Symbols Safety Message Alert Symbols Always wear approved respiratory protectionAlways wear approved eye and hearing protection Rules for Safe Operation SafetyDo not operate or service this Stow CS4030 SAW Rules for Safe OperationAlways keep the work area well organized Stow CS4030 SAW Rules for Safe OperationDiamond Blade Safety Never transport the saw with the blade mounted Saw Lifting and Loading SafetyStow CS4030 SAW Rules for Safe Operation Transporting Via truck/trailerEmergencies BatteryCase the battery liquid dilute Maintenance SafetyEngine FeaturesIntended Use This saw is not intended for dry cuttingMachine Safety Decals Stow CS4030 SAW Operation and Safety DecalsSerial Tag/Locations SerialTag Stow CS4030 SAW Serial TAG InformationLeftWater FlowValve Meters water supply Stow CS4030 SAW Controls and IndicatorsSocket Connector Use to plug in optional light Auxiliary SwitchStow CS4030 SAW Components Oil Fill Cap Remove to add engine oil Stow CS4030 SAW Basic Engine InformationAccelerator system Oil in crankcaseEngine RPM / 2000 desired BS RPM = Stow CS4030 SAW Choosing Proper Blade SizeChoosing Proper Blade Size RatioBlade RPM vs. Surface Feet Per Minute Sfpm Stow CS4030 SAW Choosing Proper Blade SizeSpecifictoolsto be Used Stow CS4030 SAW Specific Tools / SAW BladesBlade Direction of Rotation Tightening Direction Right Side Stow CS4030 SAW Installing the BladeInstalling the Blade Align flange pin through the blade into the inner flangeStacking Blades for Wide Cuts Stow CS4030 SAW Installing the Blade125-175lbs.56.7-79.4Kgofweight 12 In .48 cm Lbs 56.7-79.4 KgRemoving The Blade Guard Blade GuardBlade Guards 30 and Smaller Stow CS4030 SAW Blade GuardsStow CS4030 SAW Water Delivery Systems Installing the Flange GuardBattery Setup Stow CS4030 SAW BatteryUse Diesel Fuel only Fueling the SawHandle fuel safely Do not smoke while refuelingDraining theWater System Stow CS4030 SAW Pointer AdjustmentPointer Adjustment Cold Weather OperationTop View Setting the Depth IndicatorStow CS4030 SAW RAISE-LOWER Controls Raise Lower ControlsSetting the Depth Stop Depth Control Knob Depth Indicator PointerStow CS4030 SAW Bladeshaft Engage System Starting and Stoppingthe Engine Wheel Drive SystemStow CS4030 SAW Operation Restarting After Running Out of FuelOperating Synopsis Avoid Injury Stow CS4030 SAW Loading and TransportingMaintenance Stow CS4030 SAW MaintenanceStow CS4030 SAW Maintenance Changing Engine Oil And Filter Oil Filter 125 HoursEngine Oil Filter Filter Seal Engine Tune-Up Fuel Filter 200 HoursLubrication Prevent Crush InjuryBattery/Charging System Cooling SystemRefer to your engine manual for additional information Remove lower battery retainer, Item B, Figure Stow CS4030 SAW MaintenanceReplacing the Battery Remove rear access panelBelts and Pulleys To Stop Bladeshaft RotationTo Start Bladeshaft Rotation Blade Shaft Maintenance 16 Nut Tensioner Nut Adjustment NotchesRotary BeltTensioner Drive System Alignment Blade AlignmentBlade Flange Puller Removing the Inner Blade Flange Blade Shaft Tolerance Inner Flange Inside Face If the Inner Flange does not readilyMaximum Cut Depth Adjustment While adjustment of the DepthCircuit Breakers Raise-Lower System PTO Drive MaintenanceRaise-Lower System Troubleshooting Hydraulic System Maintenance R Control AdjustmentAdjustment Nut Rod End Push-Pull Cable Neutral Safety SwitchHydraulic System Drains Hydraulic SystemSlurry Control Strip Remove the oil reservoir cap to speed oil drainingLong Term Storage Decommissioning Saw/ComponentsStow CS4030 SAW Troubleshooting Symptom Possible Cause Solution Stow CS4030 SAW TroubleshootingBlade Troubleshooting Page Stow CS4030 SAW Wiring Diagram Terms and Conditions of Sale Stow Construction Equipment Your Local Dealer is HERE’S HOW to GET Help