Stow cs403026, cs 403016, cs403020, cs403030 operation manual Raise-Lower System Troubleshooting

Page 52

STOW CS4030 SAW — MAINTENANCE

2

8

4

5

7 3

6

1

1.Pump Motor

2.Lift Pump Reservoir

3.Raise-LowerValve (Solenoid)

4.Raise-Lower Toggle

5.Raise-Lower Wire Harness

6.Lift Cylinder

7.Lift Pump Solenoid

Figure 62. Raise-Lower System

Raise-Lower System Troubleshooting

Refer to the following table to assist in troubleshooting the Raise-

Lower System.

Table 10. Raise-Lower System Troubleshooting

Indication

Possible Causes

 

 

Won't Raise

battery discharged, raise-lower solenoid faulty, cables

loose or damaged, defective wiring

 

Won't Lower

switch bad, faulty wiring connection, coil bad, valve

cartridge bad

 

PAGE 52 — STOW CS4030 SAW • OPERATION MANUAL — REV. #0 (12/13/07)

Image 52
Contents Models Page Silicosis Warning Stow CS4030 SAW Table of Contents Stow CS4030 SAW Dimensions Chassis & Dimensions SideviewBlade Shaft Assembly Stow CS4030 SAW SpecificationsOil bath design, fully enclosed cast iron housing Stow CS4030 SAW Engine Specifications Uncrated WeightCrated Weight Automatic actuating parking brake Wheels RearTraining Checklist Training ChecklistDaily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistSafety Message Alert Symbols Always wear approved respiratory protection Safety Message Alert SymbolsAlways wear approved eye and hearing protection Safety Do not operate or service thisStow CS4030 SAW Rules for Safe Operation Rules for Safe OperationStow CS4030 SAW Rules for Safe Operation Always keep the work area well organizedDiamond Blade Safety Saw Lifting and Loading Safety Stow CS4030 SAW Rules for Safe OperationTransporting Via truck/trailer Never transport the saw with the blade mountedBattery Case the battery liquid diluteMaintenance Safety EmergenciesFeatures Intended UseThis saw is not intended for dry cutting EngineStow CS4030 SAW Operation and Safety Decals Machine Safety DecalsStow CS4030 SAW Serial TAG Information Serial Tag/Locations SerialTagStow CS4030 SAW Controls and Indicators Socket Connector Use to plug in optional lightAuxiliary Switch LeftWater FlowValve Meters water supplyStow CS4030 SAW Components Stow CS4030 SAW Basic Engine Information Accelerator systemOil in crankcase Oil Fill Cap Remove to add engine oilStow CS4030 SAW Choosing Proper Blade Size Choosing Proper Blade SizeRatio Engine RPM / 2000 desired BS RPM =Stow CS4030 SAW Choosing Proper Blade Size Blade RPM vs. Surface Feet Per Minute SfpmStow CS4030 SAW Specific Tools / SAW Blades Specifictoolsto be UsedStow CS4030 SAW Installing the Blade Installing the BladeAlign flange pin through the blade into the inner flange Blade Direction of Rotation Tightening Direction Right SideStow CS4030 SAW Installing the Blade 125-175lbs.56.7-79.4Kgofweight12 In .48 cm Lbs 56.7-79.4 Kg Stacking Blades for Wide CutsBlade Guard Removing The Blade GuardStow CS4030 SAW Blade Guards Blade Guards 30 and SmallerInstalling the Flange Guard Stow CS4030 SAW Water Delivery SystemsStow CS4030 SAW Battery Battery SetupFueling the Saw Handle fuel safelyDo not smoke while refueling Use Diesel Fuel onlyStow CS4030 SAW Pointer Adjustment Pointer AdjustmentCold Weather Operation Draining theWater SystemSetting the Depth Indicator Stow CS4030 SAW RAISE-LOWER ControlsRaise Lower Controls Top ViewDepth Control Knob Depth Indicator Pointer Setting the Depth StopStow CS4030 SAW Bladeshaft Engage System Wheel Drive System Starting and Stoppingthe EngineRestarting After Running Out of Fuel Stow CS4030 SAW OperationOperating Synopsis Stow CS4030 SAW Loading and Transporting Avoid InjuryStow CS4030 SAW Maintenance MaintenanceStow CS4030 SAW Maintenance Oil Filter 125 Hours Changing Engine Oil And FilterEngine Oil Filter Filter Seal Fuel Filter 200 Hours LubricationPrevent Crush Injury Engine Tune-UpCooling System Battery/Charging SystemRefer to your engine manual for additional information Stow CS4030 SAW Maintenance Replacing the BatteryRemove rear access panel Remove lower battery retainer, Item B, FigureTo Stop Bladeshaft Rotation Belts and PulleysTo Start Bladeshaft Rotation 16 Nut Tensioner Nut Adjustment Notches Blade Shaft MaintenanceRotary BeltTensioner Blade Alignment Drive System AlignmentBlade Flange Puller Removing the Inner Blade Flange If the Inner Flange does not readily Blade Shaft Tolerance Inner Flange Inside FaceWhile adjustment of the Depth Maximum Cut Depth AdjustmentCircuit Breakers PTO Drive Maintenance Raise-Lower SystemRaise-Lower System Troubleshooting R Control Adjustment Adjustment Nut Rod EndPush-Pull Cable Neutral Safety Switch Hydraulic System MaintenanceHydraulic System Hydraulic System DrainsRemove the oil reservoir cap to speed oil draining Long Term StorageDecommissioning Saw/Components Slurry Control StripStow CS4030 SAW Troubleshooting Stow CS4030 SAW Troubleshooting Symptom Possible Cause SolutionBlade Troubleshooting Page Stow CS4030 SAW Wiring Diagram Terms and Conditions of Sale Stow Construction Equipment HERE’S HOW to GET Help Your Local Dealer is