Stow cs 403016, cs403026, cs403020, cs403030 operation manual Daily PRE-OPERATION Checklist

Page 9

DAILY PRE-OPERATION CHECKLIST

1	Hardware and damage check.

2Engine oil level.

3Hydraulic oil level.

4Condition of blade.

5Safety Stop Switch operation.

6Braking control operation.

COMMENTS:

STOW CS4030 SAW • OPERATION MANUAL — REV. #0 (12/13/07) — PAGE 9

Image 9

Contents Models Page Silicosis Warning Stow CS4030 SAW Table of Contents Chassis & Dimensions Sideview Stow CS4030 SAW Dimensions Stow CS4030 SAW Specifications Blade Shaft Assembly Oil bath design, fully enclosed cast iron housing Uncrated Weight Stow CS4030 SAW Engine SpecificationsCrated Weight Automatic actuating parking brake Wheels RearTraining Checklist Training ChecklistDaily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistSafety Message Alert Symbols Safety Message Alert Symbols Always wear approved respiratory protectionAlways wear approved eye and hearing protection Do not operate or service this SafetyStow CS4030 SAW Rules for Safe Operation Rules for Safe OperationAlways keep the work area well organized Stow CS4030 SAW Rules for Safe OperationDiamond Blade Safety Stow CS4030 SAW Rules for Safe Operation Saw Lifting and Loading SafetyTransporting Via truck/trailer Never transport the saw with the blade mountedCase the battery liquid dilute BatteryMaintenance Safety EmergenciesIntended Use FeaturesThis saw is not intended for dry cutting EngineMachine Safety Decals Stow CS4030 SAW Operation and Safety DecalsSerial Tag/Locations SerialTag Stow CS4030 SAW Serial TAG InformationSocket Connector Use to plug in optional light Stow CS4030 SAW Controls and IndicatorsAuxiliary Switch LeftWater FlowValve Meters water supplyStow CS4030 SAW Components Accelerator system Stow CS4030 SAW Basic Engine InformationOil in crankcase Oil Fill Cap Remove to add engine oilChoosing Proper Blade Size Stow CS4030 SAW Choosing Proper Blade SizeRatio Engine RPM / 2000 desired BS RPM =Blade RPM vs. Surface Feet Per Minute Sfpm Stow CS4030 SAW Choosing Proper Blade SizeSpecifictoolsto be Used Stow CS4030 SAW Specific Tools / SAW BladesInstalling the Blade Stow CS4030 SAW Installing the BladeAlign flange pin through the blade into the inner flange Blade Direction of Rotation Tightening Direction Right Side125-175lbs.56.7-79.4Kgofweight Stow CS4030 SAW Installing the Blade12 In .48 cm Lbs 56.7-79.4 Kg Stacking Blades for Wide CutsRemoving The Blade Guard Blade GuardBlade Guards 30 and Smaller Stow CS4030 SAW Blade GuardsStow CS4030 SAW Water Delivery Systems Installing the Flange GuardBattery Setup Stow CS4030 SAW BatteryHandle fuel safely Fueling the SawDo not smoke while refueling Use Diesel Fuel onlyPointer Adjustment Stow CS4030 SAW Pointer AdjustmentCold Weather Operation Draining theWater SystemStow CS4030 SAW RAISE-LOWER Controls Setting the Depth IndicatorRaise Lower Controls Top ViewSetting the Depth Stop Depth Control Knob Depth Indicator PointerStow CS4030 SAW Bladeshaft Engage System Starting and Stoppingthe Engine Wheel Drive SystemStow CS4030 SAW Operation Restarting After Running Out of FuelOperating Synopsis Avoid Injury Stow CS4030 SAW Loading and TransportingMaintenance Stow CS4030 SAW MaintenanceStow CS4030 SAW Maintenance Changing Engine Oil And Filter Oil Filter 125 HoursEngine Oil Filter Filter Seal Lubrication Fuel Filter 200 HoursPrevent Crush Injury Engine Tune-UpBattery/Charging System Cooling SystemRefer to your engine manual for additional information Replacing the Battery Stow CS4030 SAW MaintenanceRemove rear access panel Remove lower battery retainer, Item B, FigureBelts and Pulleys To Stop Bladeshaft RotationTo Start Bladeshaft Rotation Blade Shaft Maintenance 16 Nut Tensioner Nut Adjustment NotchesRotary BeltTensioner Drive System Alignment Blade AlignmentBlade Flange Puller Removing the Inner Blade Flange Blade Shaft Tolerance Inner Flange Inside Face If the Inner Flange does not readilyMaximum Cut Depth Adjustment While adjustment of the DepthCircuit Breakers Raise-Lower System PTO Drive MaintenanceRaise-Lower System Troubleshooting Adjustment Nut Rod End R Control AdjustmentPush-Pull Cable Neutral Safety Switch Hydraulic System MaintenanceHydraulic System Drains Hydraulic SystemLong Term Storage Remove the oil reservoir cap to speed oil drainingDecommissioning Saw/Components Slurry Control StripStow CS4030 SAW Troubleshooting Symptom Possible Cause Solution Stow CS4030 SAW TroubleshootingBlade Troubleshooting Page Stow CS4030 SAW Wiring Diagram Terms and Conditions of Sale Stow Construction Equipment Your Local Dealer is HERE’S HOW to GET Help