Graco 261800 specifications Troubleshooting, Problem Cause Solution

Page 31

Troubleshooting

Troubleshooting

Check everything in this Troubleshooting Table before you bring the sprayer to a Graco/MAGNUM autho- rized service center.

Problem

Cause

Solution

 

 

 

 

 

 

Power is on and sprayer is plugged

AllControl is set at zero pressure.

Turn AllControl clockwise to increase

in, but motor does not run, and pump

 

pressure setting.

does not cycle.

 

 

Motor or control is damaged.

Take sprayer to Graco/MAGNUM

 

 

 

authorized service center.

 

 

 

 

Electric outlet is not providing power.

• Try a different outlet or plug in

 

 

something that you know is work-

 

 

ing to test outlet.

 

 

• Reset building circuit breaker or

 

 

replace fuse.

 

 

 

 

Extension cord is damaged.

Replace extension cord. Read

 

 

Grounding and Electric Require-

 

 

ments, page 4.

 

 

 

 

Sprayer electric cord is damaged.

Check for broken insulation or wires.

 

 

Replace electric cord if damaged.

 

 

 

 

Paint is frozen or hardened in pump.

Unplug sprayer from outlet. If frozen

 

 

do NOT try to start sprayer until it is

 

 

completely thawed or you may dam-

 

 

age the motor, control board and/or

 

 

drivetrain.

 

 

Make sure AllControl is OFF. Place

 

 

sprayer in a warm area for several

 

 

hours. Then plug in and turn AllCon-

 

 

trol to Prime/Clean to see if motor will

 

 

start.

 

 

If paint is hardened in sprayer, pump

 

 

packings, valves, drivetrain or pres-

 

 

sure switch may need to be replaced.

 

 

Take sprayer to Graco/MAGNUM

 

 

authorized service center.

 

 

 

 

System is already pressurized.

Turn AllControl to OFF, pause 2-3

 

 

seconds and then turn AllControl to

 

 

STORAGE to relieve pressure.

 

 

 

Pump does not prime.

AllControl not set to correct function.

Turn AllControl to PRIME/CLEAN

 

 

PRIME position.

 

 

 

 

Inlet screen is clogged.

Clean debris off inlet screen.

 

 

 

 

Pump valve check balls or seat are

Remove fittings. Clean or replace ball

 

dirty.

and seat.

 

 

 

312079A

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Project Painter 5 Airless Sprayer Fire and Explosion Hazard Equipment Misuse Hazard Grounding and Electric Requirements InstallationThermal Overload Project Painter Component IdentificationE1 M Getting Started Pressure Relief ProcedureTrigger Lock Setup AllControl SettingsHopper Method Primary Spray Method Oil- or Water-based Materials Priming and Flushing Storage Fluid Hopper MethodPRIME/CLEAN GUN Direct Immersion Setup Alternate Spray Method Priming and Flushing Storage Fluid Direct Immersion Method Install Tip and Guard Preventing Excessive Tip Wear Adjusting PressureSpraying Techniques Unclogging Spray TipCoatings Choosing the Correct Tip for the JobTip Selection Selecting Tip Hole SizeUnderstanding Tip Number Reversible Tip Selection ChartTip Fan Width 12 Part Mm from Surface Triggering Gun Getting Started With Basic TechniquesAiming Gun Rolling Ceilings, Walls and Woodwork Rolling TechniquesRelieve pressure, Shutdown & Cleaning After Hopper Method ApplicationsRelatively clear and all Power Flush PRIME/CLEAN GUN and Hose Pail Flushing Pull and hold gun trigger Turn AllControl to Open Turn off garden hose. Close Power Flush attachment Cleaning Roller Short Term Storage StorageLong Term Storage Stowing Sprayer Problem Cause Solution TroubleshootingTroubleshooting Thermal Overload, Tips Maintenance and ServiceCaring for Sprayer Paint HosesTechnical Data For Graco Canada Customers Graco Standard Warranty
Top Page Image Contents