Delta 638517-00, SM300 warranty Drilling Holes to Depth, Adjusting Spindle Return Spring

Page 13

5.After the belt is positioned on the desired steps of the motor and spindle pulleys, move motor (D) Fig. 26, to the rear until the belt is properly tensioned and tighten tension lock knob (B). The belt should be just tight enough to prevent slipping. Excessive tension will reduce the life of the belt, pulleys and bearings. Correct tension is obtained when the belt (C) can be flexed about 1" out of line midway between the pulleys using light finger pressure.

DRILLING HOLES TO DEPTH

Where a number of holes are to be drilled to exactly the same depth, a depth stop is provided in the pinion shaft housing and is used as follows:

1.DISCONNECT MACHINE FROM POWER SOURCE.

2.Insert bit into chuck.

3.Lower the spindle until the pointer (C) Fig. 27, lines up with the mark on the scale (D) you wish the depth of the holes to be drilled. Then tighten lock screw (A). Return the spindle to the up position.

4.Place the material to be drilled on the drill press table. Raise the drill press table until the material to be drilled just touches the drill bit.

5.Drill a test hole to check the adjustment and readjust if necessary. All holes will then be drilled to the exact depth as indicated on scale (D) Fig. 27. NOTE: Scale (D) is calibrated in both inches and millimeters.

ADJUSTING SPINDLE

RETURN SPRING

The spindle is automatically returned to its upper most position when the handle is released. It is recommended that the handle be allowed to slowly return to the top position after each hole has been drilled in the material. This spring has been properly adjusted at the factory and should not be disturbed unless absolutely necessary. To adjust the return spring, proceed as follows:

1.DISCONNECT MACHINE FROM POWER SOURCE.

2 . Loosen nuts (B) and (E) Fig. 28. Make sure spring housing (A) stays engaged with head casting.

3.While FIRMLY HOLDING spring housing (A) Fig. 29 pull out housing and rotate it until boss (D) is engaged with the next notch on the housing. Turn the housing counterclockwise to increase or clockwise to decrease spring tension. Turn nut (E) until it contacts spring housing (A), then back nut (E) out a 1/4 turn from spring housing (A). Tighten nut (B) against nut (E), to hold the housing in place. IMPORTANT: Inside nut (E) should not contact spring housing (A) when tightened.

B

D

C A

Fig. 27

A

BE

Fig. 28

ED

B

A

Fig. 29

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Bench Drill Press General Safety Rules Additional Safety Rules for For Drill Presses Grounding Instructions Power ConnectionsExtension Cords Packing and CleaningR E W O R D Assembly Time Estimate Assembly Tools RequiredDrill Press Parts Page Being Careful not to Overtighten Page Fastening Drill Press to Supporting Surface Operating Controls and AdjustmentsStarting and Stopping Drill Press Table Adjustments Locking Switch OFF PositionFlexible Lamp Spindle Speeds Changing Speeds and Adjusting Belt TensionDrilling Holes to Depth Adjusting Spindle Return SpringOperation Installing and Removing Drill BitsCorrect Drilling Speeds TroubleshootingBoring in Wood Drilling MetalPage PARTS, Service or Warranty Assistance AccessoriesTaladradora de Banco de 254 mm Mantenga LOS Resguardos EN SU Sitio y en buen e s t a d o Normas DE Seguridad GeneralesReglas Adicionales DE Seguridad Para LAS Taladradoras Guarde Estas InstruccionesInstrucciones DE Conexión a Tierra Conexiones a LA Fuente DE AlimentaciónDesempaquetado Y Limpieza Instrucciones DE FuncionamientoPrefacio Piezas DE LA Taladradora Ensamblaje Page Page Afianzando LA Taladradora DE Banco LA Superficie DE Apoyo DE Funcionamiento Controles Y AjustesInterruptor Lámpara Flexible Bloqueando EL Interruptor EN LA Posicion DE ApagadoAjustes DE LA Mesa Cambio DE Velocidades Y Ajuste DEL Tensionamiento DE Correa Velocidades DE ArbolAjuste DEL Resorte DE Retorno DEL Arbol Perforacion DE Agujeros a ProfundidadInstalacion Y Extraccion DE Brocas FuncionamientoVelocidades QUE Perforan Correctas Page Perforacion DE Metales Perforacion DE MaderasPIEZAS, Servicio O Asistencia DE Garantía Perceuse à colonne détabli de 25,4 cm 10 po modèle SM300 Règles Générales DE Sécurité Pour SA Propre SÉCURITÉ, Lire LE ModeConserver CES Directives Directives DE Mise À LA Terre Connexions ÉlectriquesAVA N T- P R O P O S Rallonges ÉlectriquesDésemballage ET Nettoyage Outils Nécessaires Pour L’ASSEMBLAGE Pièces DE LA Perçeuse À ColonneDurée Estimée Pour L’ASSEMBLAGE Assembler la colonne A, à la base B AssemblageCalage D, Veuillez À NE PAS Trop Serrer Page Fixation DE LA Perceuse Colonne À LA Surface DE Support Utilisation DES Commandes ET RéglagesDémarrage ET Arrêt DE LA Perceuse À Colonne Lampe Flexible Verrouillage DE Linterrupteur EN Position D« Arrêt »Réglages DE LA Table Débrancher LA Machine DE LA Source D’ALIMENTATION Vitesses DE BrocheDébrancher LA Machine DE LA Source D’ALIMENTATION Perçage DE Trous À Profondeur DéfinieInsertion ET Retrait DE Mèches FonctionnementPerçage DU Bois PA N N a G E Vitesses Correctes DE PerçagePerçage DU Métal Page Pièces Réparation OU Aide À Propos DE LA Garantie AccessoiresPORTER-CABLE · Delta Service Centers

638517-00, SM300 specifications

Delta 638517-00, SM300 is a cutting-edge model in the realm of advanced technological solutions, designed to meet the demanding needs of various industrial applications. This innovative device is lauded for its robust features, versatility, and efficiency, making it an ideal choice for professionals in multiple sectors including manufacturing, automation, and quality control.

One of the standout features of the Delta 638517-00, SM300 is its high-performance processing capability. Equipped with an advanced microprocessor, this model ensures fast data processing and real-time performance monitoring. This capability is crucial for industries that require quick decision-making and immediate feedback in their operations.

Another significant characteristic of the SM300 is its enhanced connectivity options. With support for various communication protocols, including Ethernet, USB, and serial connections, the SM300 can easily integrate into existing industrial networks. This flexibility allows for streamlined data transfer and communication, enabling seamless integration with other devices and systems, and thereby improving overall operational efficiency.

The Delta 638517-00, SM300 is also designed with user convenience in mind. It features an intuitive interface that simplifies the user experience, making it accessible for personnel with varying levels of technical expertise. The device comes with a comprehensive set of software tools that facilitate configuration, monitoring, and data analysis, allowing users to tailor the system to their specific operational needs.

Durability and reliability are key attributes of the SM300. Built to withstand harsh industrial environments, this model operates efficiently even in challenging conditions such as extreme temperatures, humidity, and dust. Its robust construction ensures minimal downtime and maintenance, thereby enhancing productivity.

Additionally, the SM300 employs advanced sensor technology. This allows for enhanced measurement accuracy and better data collection, which are critical for quality control and process optimization. The model supports various types of sensors, enabling users to customize their setup according to the specific requirements of their applications.

In conclusion, the Delta 638517-00, SM300 stands out as a powerful tool in industrial automation and control. With its powerful processing capabilities, versatile connectivity options, and user-friendly interface, it is designed to enhance operational efficiency and reliability in demanding environments. As industries continue to evolve, models like the SM300 will play a crucial role in driving technological advancement and operational success.
Top Page Image Contents