Delta SM300, 638517-00 warranty Power Connections, Grounding Instructions

Page 4

POWER CONNECTIONS

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3- prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the machine to the power line, make sure the switch (s) is in the “OFF” position and be sure that the electric current is of the same characteristics as indicated on the machine. All line connections should make good contact. Running on low voltage will damage the machine.

SHOCK HAZARD. DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS .

GROUNDING INSTRUCTIONS

SHOCK HAZARD. THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRIC SHOCK. Your machine is wired for 120 Volt, 60 HZ alternating current. Before connecting the machine to the power source, make sure the switch is in the “OFF” position.

1. All grounded, cord-connected machines:

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This machine is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances .

Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician.

Improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment- grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.

Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the machine is properly grounded.

Use only 3-wire extension cords that have 3-prong grounding type plugs and matching 3-conductor receptacles that accept the machine’s plug, as shown in Fig. A .

Repair or replace damaged or worn cord immediately.

GROUNDED OUTLET BOX

CURRENT

CARRYING

PRONGS

2.Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating less than 150 volts:

If the machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig. A, the machine will have a grounding plug that looks like the plug illustrated in Fig. A. A temporary adapter, which looks like the adapter illustrated in Fig. B, may be used to connect this plug to a matching 2-conductor receptacle as shown in Fig. B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician. The green-colored rigid ear, lug, and the like, extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. Whenever the adapter is used, it must be held in place with a metal screw.

NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian Electric Code.

SHOCK HAZARD. IN ALL CASES, MAKE CERTAIN THE RECEPTACLE IN QUESTION IS PROPERLY GROUNDED. IF YOU ARE NOT SURE HAVE A Q U A L I F I E D ELECTRICIAN CHECK THE RECEPTACLE .

GROUNDED OUTLET BOX

GROUNDING

MEANS

ADAPTER

GROUNDING BLADE

Fig. A

Fig. B

IS LONGEST OF THE 3 BLADES

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Bench Drill Press General Safety Rules Additional Safety Rules for For Drill Presses Power Connections Grounding InstructionsExtension Cords Packing and CleaningR E W O R D Assembly Time Estimate Assembly Tools RequiredDrill Press Parts Page Being Careful not to Overtighten Page Fastening Drill Press to Supporting Surface Operating Controls and AdjustmentsStarting and Stopping Drill Press Table Adjustments Locking Switch OFF PositionFlexible Lamp Changing Speeds and Adjusting Belt Tension Spindle SpeedsAdjusting Spindle Return Spring Drilling Holes to DepthInstalling and Removing Drill Bits OperationTroubleshooting Correct Drilling SpeedsBoring in Wood Drilling MetalPage Accessories PARTS, Service or Warranty AssistanceTaladradora de Banco de 254 mm Normas DE Seguridad Generales Mantenga LOS Resguardos EN SU Sitio y en buen e s t a d oGuarde Estas Instrucciones Reglas Adicionales DE Seguridad Para LAS TaladradorasConexiones a LA Fuente DE Alimentación Instrucciones DE Conexión a TierraDesempaquetado Y Limpieza Instrucciones DE FuncionamientoPrefacio Piezas DE LA Taladradora Ensamblaje Page Page Afianzando LA Taladradora DE Banco LA Superficie DE Apoyo DE Funcionamiento Controles Y AjustesInterruptor Lámpara Flexible Bloqueando EL Interruptor EN LA Posicion DE ApagadoAjustes DE LA Mesa Velocidades DE Arbol Cambio DE Velocidades Y Ajuste DEL Tensionamiento DE CorreaPerforacion DE Agujeros a Profundidad Ajuste DEL Resorte DE Retorno DEL ArbolInstalacion Y Extraccion DE Brocas FuncionamientoVelocidades QUE Perforan Correctas Page Perforacion DE Metales Perforacion DE MaderasPIEZAS, Servicio O Asistencia DE Garantía Perceuse à colonne détabli de 25,4 cm 10 po modèle SM300 Pour SA Propre SÉCURITÉ, Lire LE Mode Règles Générales DE SécuritéConserver CES Directives Connexions Électriques Directives DE Mise À LA TerreAVA N T- P R O P O S Rallonges ÉlectriquesDésemballage ET Nettoyage Outils Nécessaires Pour L’ASSEMBLAGE Pièces DE LA Perçeuse À ColonneDurée Estimée Pour L’ASSEMBLAGE Assemblage Assembler la colonne A, à la base BCalage D, Veuillez À NE PAS Trop Serrer Page Fixation DE LA Perceuse Colonne À LA Surface DE Support Utilisation DES Commandes ET RéglagesDémarrage ET Arrêt DE LA Perceuse À Colonne Lampe Flexible Verrouillage DE Linterrupteur EN Position D« Arrêt »Réglages DE LA Table Vitesses DE Broche Débrancher LA Machine DE LA Source D’ALIMENTATIONPerçage DE Trous À Profondeur Définie Débrancher LA Machine DE LA Source D’ALIMENTATIONFonctionnement Insertion ET Retrait DE MèchesPerçage DU Bois PA N N a G E Vitesses Correctes DE PerçagePerçage DU Métal Page Accessoires Pièces Réparation OU Aide À Propos DE LA GarantiePORTER-CABLE · Delta Service Centers

638517-00, SM300 specifications

Delta 638517-00, SM300 is a cutting-edge model in the realm of advanced technological solutions, designed to meet the demanding needs of various industrial applications. This innovative device is lauded for its robust features, versatility, and efficiency, making it an ideal choice for professionals in multiple sectors including manufacturing, automation, and quality control.

One of the standout features of the Delta 638517-00, SM300 is its high-performance processing capability. Equipped with an advanced microprocessor, this model ensures fast data processing and real-time performance monitoring. This capability is crucial for industries that require quick decision-making and immediate feedback in their operations.

Another significant characteristic of the SM300 is its enhanced connectivity options. With support for various communication protocols, including Ethernet, USB, and serial connections, the SM300 can easily integrate into existing industrial networks. This flexibility allows for streamlined data transfer and communication, enabling seamless integration with other devices and systems, and thereby improving overall operational efficiency.

The Delta 638517-00, SM300 is also designed with user convenience in mind. It features an intuitive interface that simplifies the user experience, making it accessible for personnel with varying levels of technical expertise. The device comes with a comprehensive set of software tools that facilitate configuration, monitoring, and data analysis, allowing users to tailor the system to their specific operational needs.

Durability and reliability are key attributes of the SM300. Built to withstand harsh industrial environments, this model operates efficiently even in challenging conditions such as extreme temperatures, humidity, and dust. Its robust construction ensures minimal downtime and maintenance, thereby enhancing productivity.

Additionally, the SM300 employs advanced sensor technology. This allows for enhanced measurement accuracy and better data collection, which are critical for quality control and process optimization. The model supports various types of sensors, enabling users to customize their setup according to the specific requirements of their applications.

In conclusion, the Delta 638517-00, SM300 stands out as a powerful tool in industrial automation and control. With its powerful processing capabilities, versatile connectivity options, and user-friendly interface, it is designed to enhance operational efficiency and reliability in demanding environments. As industries continue to evolve, models like the SM300 will play a crucial role in driving technological advancement and operational success.
Top Page Image Contents