Assembly Operation | Beckett 0602-20, 0612-20 manual

ASSEMBLY

OPERATION

WARNING!

Always remove battery pack before changing or removing ac- cessories. Only use accessories specifically recommended for this tool. Others may be hazardous.

Clip-LokTMSystem (Fig. 3 & 4)

The Clip-Lok system consists of three pieces; the belt clip, the tool holder, and the bit holder.

Fig. 3

Belt clip

Bit holder

Tool holder

Front tangs

The system is shipped assembled for right- handed use. To change the assembly for left-handed use:

Attaching the Belt Clip (Fig. 4)

	Fig. 4	Clamp release
	Fig. 4	lever
		lever
		Stud

Clamp

Tool

release lever

The belt clip can be mounted to tool belts, bags, buckets, etc. To mount the belt clip:

1.Push and hold the clamp release lever.

2.Pull out the clamp at the back of the belt clip and release the clamp release lever.

3.Slide the clamp over the desired tool belt, bag, bucket, etc.

4.Press in the clamp to achieve the de- sired tightness.

WARNING!

To reduce the risk of injury, wear safety goggles or glasses with side shields.

Using Keyless Chucks (Fig. 5)

Your cordless tool is equipped with a spindle lock that allows the chuck to be tightened with one hand.

Always remove the battery pack or lock the trigger before inserting or removing bits.

Fig. 5

Open

Sleeve

1. To open the chuck jaws, turn the sleeve

in the "OPEN" direction indicated on

the chuck.

When using drill bits, allow the bit to

strike the bottom of the chuck. Center

the bit in the chuck jaws and lift it about

1/16" off of the bottom.

When using screwdriver bits, insert

Using Clutch (Fig. 6)

This tool has an adjustable clutch for driv- ing different types of screws into differ- ent materials. When properly adjusted, the clutch will slip at a preset torque to pre- vent driving the screw too deep and to prevent damage to the screw or tool.

To adjust the clutch, turn the torque selec- tor collar to one of the twenty positions shown on the collar. The number must line up with the arrow on top of the tool.

Fig. 6	Torque	Position
	Torque	numbers
	selector	numbers
	selector
	collar

The torque specifications shown here are approximate values obtained with a fully charged battery pack.

	0602-20	0612-20
Positions	Torque	Torque
1 - 5	0 - 10 in. lbs.	0 - 10 in. lbs.

6 - 10	12 - 21 in. lbs.	12 - 21 in. lbs.

1.Remove battery pack.

2.Remove screws holding the tool holder and the bit holder.

3.Lift the holders at the narrow end and pull the front tangs out of their slots.

4.Replace the pieces onto the desired side by sliding the tangs into the slots. Tighten the screws securely.

Using the Clip-Lok Tool Holder

1.To attach the tool to the belt clip, slide the tool holder over the stud on the belt clip until it is held in place by the protruding pin.

2.To release the tool from the belt clip, grasp the tool handle, push down on the tool release lever with your thumb, and pull up on the tool.

Using the Clip-Lok Bit Holder

The bit holder holds two standard 1/4" hex shank bits up to two inches long.

1.Insert the bit by pressing it into the clip.

2.Remove the bit by lifting the tip of the bit and pulling it out of the clip.

the bit far enough for the chuck jaws

to grip the hex of the bit.

2. To close the chuck jaws, turn the

sleeve in the "CLOSE" direction indi-

cated on the chuck. The bit is secure

when the chuck makes a ratcheting

sound and the sleeve can not be ro-

tated any further.

NOTE: A ratcheting sound may be heard when the chuck is opened or closed. This noise is part of the locking feature, and does not indicate a problem with the chuck's operation.

11 - 15	24 - 32 in. lbs.	24 - 32 in. lbs.

16 - 20	35 - 44 in. lbs.	35 - 44 in. lbs.

Drill
Low	280 in. lbs.	390 in. lbs
High	80 in. lbs.	100 in. lbs.

NOTE: Because the above settings are only a guide, use a piece of scrap material to test the different clutch positions before driving screws into the workpiece.