Bostitch RN46 manual Safety Instructions, AIR Supply and Connections, Loading Tool, Operation

Page 3

SAFETY INSTRUCTIONS

EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI Z87.1 and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection.

CAUTION: Additional Safety Protection will be required in some environments. For example, the working area may include exposure to noise level which can lead to hearing damage. The employer and user must ensure that any necessary hearing protection is provided and used by the operator and others in the work area. Some environments will require the use of head protection equipment. When required, the employer and user must ensure that head protection conforming to ANSI Z89.1 is used.

AIR SUPPLY AND CONNECTIONS

Do not use oxygen, combustible gases, or bottled gases as a power source for this tool as tool may explode, possibly causing injury.

Do not use supply sources which can potentially exceed 200 P.S.I.G. as tool may burst, possibly causing injury.

The connector on the tool must not hold pressure when air supply is disconnected. If a wrong fitting is used, the tool can remain charged with air after disconnecting and thus will be able to drive a fastener even after the air line is disconnected possibly causing injury.

Do not pull trigger or depress contact arm while connected to the air supply as the tool may cycle, possibly causing injury.

Always disconnect air supply: 1.) Before making adjustments; 2.) When servicing the tool; 3.) When clearing a jam; 4.) When tool is not in use; 5.) When moving to a different work area, as accidental actuation may occur, possibly causing injury.

LOADING TOOL

When loading tool: 1.) Never place a hand or any part of body in fastener discharge area of tool; 2.) Never point tool at anyone; 3.) Do not pull the trigger or depress the trip as accidental actuation may occur, possibly causing injury.

OPERATION

Always handle the tool with care: 1.) Never engage in horseplay; 2.) Never pull the trigger unless nose is directed toward the work; 3.) Keep others a safe distance from the tool while tool is in operation as accidental actuation may occur, possibly causing injury.

The operator must not hold the trigger pulled on contact arm tools except during fastening operation as serious injury could result if the trip accidentally contacted someone or something, causing the tool to cycle.

Keep hands and body away from the discharge area of the tool. A contact arm tool may bounce from the recoil of driving a fastener and an unwanted second fastener may be driven possibly causing injury.

Check operation of the contact arm mechanism frequently. Do not use the tool if the arm is not working correctly as accidental driving of a fastener may result. Do not interfere with the proper operation of the contact arm mechanism.

Do not drive fasteners on top of other fasteners or with the tool at an overly steep angle as this may cause deflection of fasteners which could cause injury.

Do not drive fasteners close to the edge of the work piece as the wood may split, allowing the fastener to be deflected possibly causing injury.

This nailer produces SPARKS during operation. NEVER use the nailer near flammable substances, gases or vapors including lacquer, paint, benzine, thinner, gasoline, adhesives, mastics, glues or any other material that is -- or the vapors, fumes or byproducts of which are -- flammable, combustible or explosive. Using the nailer in any such environment could cause an EXPLOSION resulting in personal injury or death to user and bystanders.

MAINTAINING THE TOOL

When working on air tools note the warnings in this manual and use extra care when evaluating problem tools.

3

Image 3
Contents RN46 Introduction Index Limited Warranty U.S. and Canada OnlyOperation Safety InstructionsAIR Supply and Connections Loading ToolOperating Pressure Tool SpecificationsFastener Specifications Tool AIR FittingLubrication To Prevent Accidental Injuries Loading the RN46Lock-Out Mechanism Shingle GaugeCleaning the Roofing Nailer DIAL-A-DEPTH Fastener Control AdjustmentTrigger Operation Tool OperationContact Trip Operation Sequential Trip OperationMaintaining the Pneumatic Tool Tool Operation CheckRN46 Driver Maintenance Instructions Coil Nailers Trouble ShootingIntroducción Índice NotaGarantía Limitada Sólo EE.UU. y Canadá Operación Instrucciones DE SeguridadSuministro DE Aire Y Conexiones AL Cargar LA HerramientaFuncionamiento Especificaciones DE LA HerramientaEspecificaciones DE Clavos Conector DE Aire DE LA HerramientaLubricación Para Prevenir Lesiones Accidentales Carga DE LA RN46Mecanismo de bloqueo Medidor de tejasAjuste DE Control Para Clavar O Engrapar DIAL-A-DEPTH Limpieza DE LA Clavadora Para TechadoFuncionamiento CON Gatillo Funcionamiento DE LA HerramientaFuncionamiento DEL Disparo DE Contacto Funcionamiento DEL Disparo SecuencialMantenimiento DE LA Herramienta Neumática Revisión Funcional DE LA HerramientaPage Clavadoras DE Rollo Solución DE ProblemasGarantie Limitée É.-U. et Canada seulement RemarqueFonctionnement Consignes DE SécuritéAlimentation EN AIR Comprimé ET Raccordement Chargement DE L’APPAREILPression DE Fonctionnement Caractéristiques Techniques DE L’OUTILSpécifications DES Attaches Raccord PneumatiqueLubrification Alimentation EN AIR ET ConnexionsPour Prévenir Tout Accident Chargement DU RN46Mécanisme de verrouillage Calibre à bardeauxNettoyage DU Fusil À Clous Pour Couvreur Commande DE Réglage DES Attaches DIAL-A-DEPTHActionné À LA Gâchette Fonctionnement DE L’OUTILFonctionnement DE LA Butée DE Déclenchement Séquence DE DéclenchementVérification DE L’ÉTAT DE Marche DE L’OUTIL Maintenance DE L’OUTIL PneumatiqueFusil À Clous RN46 Instructions DE Maintenance Marteaux Cloueurs À BANDE-CARTOUCHE Dépannage

RN46 specifications

The Bostitch RN46 is a reliable and powerful roofing nailer designed for professionals in the construction industry. Renowned for its efficiency and durability, this tool has become a favorite among roofers and contractors working on residential and commercial projects alike.

One of the standout features of the RN46 is its lightweight design, weighing just around 6.4 pounds, which allows for extended use without causing excessive fatigue. The nailer is built with an aluminum housing that enhances its durability, ensuring it can withstand the rigors of job site conditions. The RN46 is equipped with an adjustable depth control that enables users to set the depth of their nails with precision, accommodating various roofing materials effortlessly.

Incorporating advanced technologies, the Bostitch RN46 features a high-capacity magazine that holds up to 120 nails, reducing the frequency of reloads and maximizing productivity. It is compatible with 15-gauge wire collated roofing nails, which are ideal for applications involving asphalt shingles, wooden shakes, and other roofing materials. The tool is designed for rapid-fire operation, allowing users to achieve higher speeds in nail placement.

The RN46 comes with a 360-degree adjustable exhaust that directs exhaust air away from the user and the work surface, maintaining a clean environment and enhancing comfort during operation. Additionally, it features a removable nosepiece for easy troubleshooting and maintenance, ensuring that it remains in optimal working condition over time.

The Bostitch RN46 is also equipped with a secure lock mechanism that prevents accidental firing, enhancing safety for users in high-paced environments. Its ergonomic handle provides a comfortable grip, further facilitating prolonged use without strain.

Overall, the Bostitch RN46 roofing nailer is a top-tier tool that combines innovative features with user-friendly design. Whether for new roof installations or repairs, this nailer provides consistent performance, making it an essential addition to any roofing professional's toolkit. Its blend of power, efficiency, and durability sets it apart as a trusted choice for those looking to tackle roofing projects with confidence.