Bostitch RN46 manual Tool Operation, Contact Trip Operation, Sequential Trip Operation

Page 8

TOOL OPERATION

EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI Z87.1-1989 (R1998) and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection.

BEFORE HANDLING OR OPERATING THIS TOOL:

I.READ AND UNDERSTAND THE WARNINGS CONTAINED IN THIS MANUAL.

II. REFER TO “TOOL SPECIFICATIONS” IN THIS MANUAL TO IDENTIFY THE OPERATING SYSTEM ON YOUR TOOL.

There are three available systems on BOSTITCH pneumatic tools. They are:

1. CONTACT TRIP OPERATION 2. SEQUENTIAL TRIP OPERATION 3.TRIGGER OPERATION

OPERATION

1.CONTACT TRIP OPERATION:

The CONTACT TRIP MODEL tool contains a contact trip that operates in conjunction with the trigger to drive a fastener. There are two methods of operation to drive fasteners with a contact trip tool.

A. SINGLE FASTENER PLACEMENT: To operate the tool in this manner, first position the contact trip on the work surface, WITHOUT PULLING THE TRIGGER. Depress the contact trip until the nose touches the work surface and then pull the trigger to drive a fastener. Do not press the tool against the work with extra force. Instead, allow the tool to recoil off the work surface to avoid a second unwanted fastener. Remove your finger from the trigger after each operation.

B. RAPID FASTENER OPERATION: To operate the tool in this manner, hold the tool with the contact trip pointing towards but not touching the work surface. Pull the trigger and then tap the contact trip against the work surface using a bouncing motion. Each depression of the contact trip will cause a fastener to be driven.

The operator must not hold the trigger pulled on contact trip tools except during fastening operation, as serious injury could result if the trip accidentally contacted someone or something, causing the tool to cycle.

Keep hands and body away from the discharge area of the tool. A contact trip tool may bounce from the recoil of driving a fastener and an unwanted second fastener may be driven, possibly causing injury.

2.SEQUENTIAL TRIP OPERATION:

The SEQUENTIAL TRIP MODEL contains a contact trip that operates in conjunction with the trigger to drive a fastener. To operate a sequential trip tool, first position the contact trip on the work surface WITHOUT PULLING THE TRIGGER. Depress the contact trip and then pull the trigger to drive a fastener. As long as the contact trip is contacting the work and is held depressed, the tool will drive a fastener each time the trigger is depressed. If the contact trip is allowed to leave the work surface, the sequence described above must be repeated to drive another fastener.

3.TRIGGER OPERATION:

The TRIGGER OPERATED tool requires a single action to drive a fastener. Each time the trigger is pulled the tool will drive a fastener. This model does not have a contact trip and is intended for use only where a contact trip cannot be used to satisfy the requirements of the application.

8

Image 8
Contents RN46 Limited Warranty U.S. and Canada Only Introduction IndexSafety Instructions AIR Supply and ConnectionsLoading Tool OperationTool Specifications Fastener SpecificationsTool AIR Fitting Operating PressureLubrication Loading the RN46 Lock-Out MechanismShingle Gauge To Prevent Accidental InjuriesDIAL-A-DEPTH Fastener Control Adjustment Cleaning the Roofing NailerTool Operation Contact Trip OperationSequential Trip Operation Trigger OperationTool Operation Check Maintaining the Pneumatic ToolRN46 Driver Maintenance Instructions Trouble Shooting Coil NailersGarantía Limitada Sólo EE.UU. y Canadá Introducción ÍndiceNota Instrucciones DE Seguridad Suministro DE Aire Y ConexionesAL Cargar LA Herramienta OperaciónEspecificaciones DE LA Herramienta Especificaciones DE ClavosConector DE Aire DE LA Herramienta FuncionamientoLubricación Carga DE LA RN46 Mecanismo de bloqueoMedidor de tejas Para Prevenir Lesiones AccidentalesLimpieza DE LA Clavadora Para Techado Ajuste DE Control Para Clavar O Engrapar DIAL-A-DEPTHFuncionamiento DE LA Herramienta Funcionamiento DEL Disparo DE ContactoFuncionamiento DEL Disparo Secuencial Funcionamiento CON GatilloRevisión Funcional DE LA Herramienta Mantenimiento DE LA Herramienta NeumáticaPage Solución DE Problemas Clavadoras DE RolloRemarque Garantie Limitée É.-U. et Canada seulementConsignes DE Sécurité Alimentation EN AIR Comprimé ET RaccordementChargement DE L’APPAREIL FonctionnementCaractéristiques Techniques DE L’OUTIL Spécifications DES AttachesRaccord Pneumatique Pression DE FonctionnementAlimentation EN AIR ET Connexions LubrificationChargement DU RN46 Mécanisme de verrouillageCalibre à bardeaux Pour Prévenir Tout AccidentCommande DE Réglage DES Attaches DIAL-A-DEPTH Nettoyage DU Fusil À Clous Pour CouvreurFonctionnement DE L’OUTIL Fonctionnement DE LA Butée DE DéclenchementSéquence DE Déclenchement Actionné À LA GâchetteMaintenance DE L’OUTIL Pneumatique Vérification DE L’ÉTAT DE Marche DE L’OUTILFusil À Clous RN46 Instructions DE Maintenance Dépannage Marteaux Cloueurs À BANDE-CARTOUCHE

RN46 specifications

The Bostitch RN46 is a reliable and powerful roofing nailer designed for professionals in the construction industry. Renowned for its efficiency and durability, this tool has become a favorite among roofers and contractors working on residential and commercial projects alike.

One of the standout features of the RN46 is its lightweight design, weighing just around 6.4 pounds, which allows for extended use without causing excessive fatigue. The nailer is built with an aluminum housing that enhances its durability, ensuring it can withstand the rigors of job site conditions. The RN46 is equipped with an adjustable depth control that enables users to set the depth of their nails with precision, accommodating various roofing materials effortlessly.

Incorporating advanced technologies, the Bostitch RN46 features a high-capacity magazine that holds up to 120 nails, reducing the frequency of reloads and maximizing productivity. It is compatible with 15-gauge wire collated roofing nails, which are ideal for applications involving asphalt shingles, wooden shakes, and other roofing materials. The tool is designed for rapid-fire operation, allowing users to achieve higher speeds in nail placement.

The RN46 comes with a 360-degree adjustable exhaust that directs exhaust air away from the user and the work surface, maintaining a clean environment and enhancing comfort during operation. Additionally, it features a removable nosepiece for easy troubleshooting and maintenance, ensuring that it remains in optimal working condition over time.

The Bostitch RN46 is also equipped with a secure lock mechanism that prevents accidental firing, enhancing safety for users in high-paced environments. Its ergonomic handle provides a comfortable grip, further facilitating prolonged use without strain.

Overall, the Bostitch RN46 roofing nailer is a top-tier tool that combines innovative features with user-friendly design. Whether for new roof installations or repairs, this nailer provides consistent performance, making it an essential addition to any roofing professional's toolkit. Its blend of power, efficiency, and durability sets it apart as a trusted choice for those looking to tackle roofing projects with confidence.