Agilent Technologies 8922 P manual HSCSdMASTerUPLinkAMPLitude

Page 66

	Remote operation
	HSCSD Subsystem GPIB Commands
	HSCSd:MASTer:UPLink:AMPLitude
Description	This sets the expected input level of the master TCH. In standard mode,
	this sets the master’s uplink amplitude control to MANUAL. In
	compatibility mode, if the master’s uplink amplitude control is set to MS
	TX LEV then an error message Can’t change setting while MS TX
	Lev mode is selected. occurs and the setting is not performed.
	If the measurement timeslot is set to Master, the analyser level of the
	unit is set to this value.
Syntax	HSCSd:MASTer:UPLink:AMPLitude?
	HSCSd:MASTer:UPLink:AMPLitude <real> <units>

Command options

Type	ﬂoat

Units:	dBm only

Limits (GSM900):	-27.0 thru +41.0

Limits (E-GSM):	-27.0 thru +41.0

Limits (DCS1800):	-47.0 thru +33.0

Limits (PCS1900):	-47.0 thru +33.0

Default (compatibility mode):	33.0

Default (GSM900)	13.0

Default (E-GSM):	13.0

Default (DCS1800):	10.0

Default (PCS1900):	10.0

52

Chapter 5

Image 66

Contents HP/Agilent 8922 GSM Hscsd Test System Option #K09 Warranty Limitation of Remedies and Liability Assistance Statement of Compliance Sound Emission Manufacturer’s DeclarationEarthing ground, incorporated in the power cord. The mains Instrument dangerous. Intentional interruption isProhibited Safety Symbols Safety SymbolsISM 1-A Overview User’s Guide AbbreviationsContents Remote operation Returning equipment for repair Upgrading the HOP Controller ROM and Firmware Understanding the HP/Agilent Getting an overview of the HP/Agilent GSM Hscsd Test System HP/Agilent 8922 GSM Hscsd Test System, option #K09Chapter Features Setting up the HP/Agilent Before you start Checking the HP/Agilent 8922 Requirements for Hscsd Making the front panel connections Front panel connectionsMaking the rear panel connections StepRear panel connections Enabling the Hscsd functionality Inserting the keycard into the HP/AgilentTests screen Conﬁg screen Calibrating the overall system Manual operation Conﬁguring the system Message Frame reset sent appears in the top left-hand corner Establishing a call Making measurements Choosing which timeslot to measureMeasuring BER Changing power levels, timeslot and channels Hscsd control screenEnding a call Ending a call Screens Conﬁg screen Instrument typeChapter Slave address Hscsd screen Master downlink amplitudeSlave offset Master channelSelect ‘Master’ to measure before signalling mobile Master timeslot Slave timeslotCall Type Data rate MeasureMaster Tx level Master input level Master mode Slave Tx levelSlave input level Slave control Peak power display Mobile reportsTo Screen menu Fast BER Screen Fast BER screenLoopback Remote operation Introduction Conﬁgure Subsystem Gpib Commands CONFigureINSTrumentTYPEConﬁgure Instrument Type comand syntax Display Subsystem Gpib Commands Display Screen command syntaxDISPlaySCReen Hscsd Hscsd Subsystem Gpib Commands Hscsd command syntax master unit Hscsd command syntax slave unit SYNC? TCHHSCSdMASTerTCHARFCn HSCSdMASTerSTATusTCHTSLot Command 0ptions HSCSdMASTerDOWNlinkAMPLitudeHSCSdMASTerTCHTLEVel HSCSdMASTerUPLinkAMPLitude HSCSdMASTerUPLinkAMPLitudeCONTrol HSCSDMASTerCALLTYPE HSCSDMASTerCALLRATE HSCSdSLAVeSTATusSYNC HSCSdSLAVeSTATusTCHTSLot? HSCSdSLAVeDOWNlinkAMPLitudeOFFSet HSCSdSLAVeTCHTLEVel HSCSdSLAVeUPLinkAMPLitude HSCSdSLAVeUPLinkAMPLitudeCONTrol Remote operating procedures Conﬁguring the systemEstablishing a call Making measurementsChanging channels, timeslot and power levels Ending a call Example code showing a dual-band handover from E-GSM to DCS Clear ScreenPause Example code showing a dual-band handover from E-GSM to DCS Returning equipment for repair Return Procedure Chapter Sales and Service Ofﬁces Canada Sales and Service Ofﬁces Upgrading the HOP Controller ROM and Firmware Upgrading the Hop Controller ROM ROMSide View Figure A-3 Removing the A33 Hop Controller Board Figure A-4 Removing the A33 U62 HOP Controller ROMUpgrading the Hop Controller ROM Upgrading the ﬁrmware