Agilent Technologies 8922 P manual Pause

Page 81

Remote operation

Example code showing a dual-band handover from E-GSM to DCS

350! enabled, it will IMMEDIATELY return ENABLED

360!

370! Select the HSCSD screen - it's easier to see what's

380! happening for now

390OUTPUT Master;"DISP HSCSD"

400OUTPUT Slave;"DISP HSCSD"

410!

420! Dial in RF losses

430!

440OUTPUT Master;"Conf:OFLevel:RFInOut ";-1*Master_loss

450OUTPUT Master;"Conf:OFLevel:Mode 'On'"

460OUTPUT Slave;"Conf:OFLevel:RFInOut ";-1*Slave_loss

470OUTPUT Slave;"Conf:OFLevel:Mode 'On'"

480!

490! select big tx levels

500OUTPUT Master;"HSCSD:Master:TCH:TLevel 5"

510OUTPUT Slave;"HSCSD:Slave:TCH:TLevel 5"

520!

530! Get a call up

540!

550! Make sure master is listening to master uplink

560!

570OUTPUT Master;"HSCSD:Measure:TSlot 'Master'"

580!

590! and wait for the call

600!

610PRINT "Make a call from the mobile..."

620REPEAT

630

WAIT .5

640OUTPUT Master;"Cell:Call:Stat:Stat?"

650ENTER Master;Stat$

660UNTIL Stat$="""CONNECTED"""

670PRINT "Call connected, press CONTINUE key to continue..."

680PAUSE

690!

700! Now perform a dual band handover 710 !

720OUTPUT Master;"Disp DBand"

730OUTPUT Slave;"Disp DBand"

740OUTPUT Master;"DualBand:TCH:DCS 615"

750OUTPUT Master;"DualBand:TLevel:DCS 6"

760OUTPUT Master;"DualBand:Atten:GBCH '10 dB'"

770OUTPUT Master;"DualBand:Amplitude:DTCH -55 dBm"

780OUTPUT Slave;"DualBand:TCH:DCS 615"

790 OUTPUT Slave;"DualBand:TLevel:DCS 6

800OUTPUT Slave;"DualBand:Atten:GBCH '10 dB'"

810OUTPUT Slave;"DualBand:Amplitude:DTCH -55 dBm"

Chapter 5

67

Image 81

Contents HP/Agilent 8922 GSM Hscsd Test System Option #K09 Warranty Limitation of Remedies and Liability Assistance Statement of Compliance Manufacturer’s Declaration Sound EmissionEarthing ground, incorporated in the power cord. The mains Instrument dangerous. Intentional interruption isProhibited Safety Symbols Safety SymbolsISM 1-A User’s Guide Abbreviations OverviewContents Remote operation Returning equipment for repair Upgrading the HOP Controller ROM and Firmware Understanding the HP/Agilent HP/Agilent 8922 GSM Hscsd Test System, option #K09 Getting an overview of the HP/Agilent GSM Hscsd Test SystemChapter Features Setting up the HP/Agilent Before you start Checking the HP/Agilent 8922 Requirements for Hscsd Front panel connections Making the front panel connectionsStep Making the rear panel connectionsRear panel connections Inserting the keycard into the HP/Agilent Enabling the Hscsd functionalityTests screen Conﬁg screen Calibrating the overall system Manual operation Conﬁguring the system Message Frame reset sent appears in the top left-hand corner Establishing a call Making measurements Choosing which timeslot to measureMeasuring BER Hscsd control screen Changing power levels, timeslot and channelsEnding a call Ending a call Screens Instrument type Conﬁg screenChapter Slave address Master downlink amplitude Hscsd screenMaster channel Slave offsetSelect ‘Master’ to measure before signalling mobile Slave timeslot Master timeslotCall Type Measure Data rateMaster Tx level Master input level Slave Tx level Master modeSlave input level Slave control Peak power display Mobile reportsTo Screen menu Fast BER screen Fast BER ScreenLoopback Remote operation Introduction Conﬁgure Subsystem Gpib Commands CONFigureINSTrumentTYPEConﬁgure Instrument Type comand syntax Display Subsystem Gpib Commands Display Screen command syntaxDISPlaySCReen Hscsd Hscsd Subsystem Gpib Commands Hscsd command syntax master unit SYNC? TCH Hscsd command syntax slave unitHSCSdMASTerTCHARFCn HSCSdMASTerSTATusTCHTSLot HSCSdMASTerDOWNlinkAMPLitude Command 0ptionsHSCSdMASTerTCHTLEVel HSCSdMASTerUPLinkAMPLitude HSCSdMASTerUPLinkAMPLitudeCONTrol HSCSDMASTerCALLTYPE HSCSDMASTerCALLRATE HSCSdSLAVeSTATusSYNC HSCSdSLAVeSTATusTCHTSLot? HSCSdSLAVeDOWNlinkAMPLitudeOFFSet HSCSdSLAVeTCHTLEVel HSCSdSLAVeUPLinkAMPLitude HSCSdSLAVeUPLinkAMPLitudeCONTrol Conﬁguring the system Remote operating proceduresMaking measurements Establishing a callChanging channels, timeslot and power levels Ending a call Clear Screen Example code showing a dual-band handover from E-GSM to DCSPause Example code showing a dual-band handover from E-GSM to DCS Returning equipment for repair Return Procedure Chapter Sales and Service Ofﬁces Canada Sales and Service Ofﬁces Upgrading the HOP Controller ROM and Firmware ROM Upgrading the Hop Controller ROMSide View Figure A-4 Removing the A33 U62 HOP Controller ROM Figure A-3 Removing the A33 Hop Controller BoardUpgrading the Hop Controller ROM Upgrading the ﬁrmware