Agilent Technologies 8922 P manual HSCSdSLAVeUPLinkAMPLitude

Page 74

	Remote operation
	HSCSD Subsystem GPIB Commands
	HSCSd:SLAVe:UPLink:AMPLitude
Description	This sets the expected input level of the slave timeslot.
	In standard mode, this sets the slave’s uplink amplitude control to
	MANUAL. In compatibility mode, if the slave’s uplink amplitude control is
	set to MS TX LEV then an error occurs and the setting is not performed. If
	the measurement timeslot (see page 43) is set to Slave, the analyser
	level of the unit is set to this value.
Syntax	HSCSd:SLAVe:UPLink:AMPLitude?
	HSCSd:SLAVe:UPLink:AMPLitude <real> <units>
Command options

	Type	ﬂoat

	Units:	dBm only

	Limits (GSM900):	-27.0 thru +41.0

	Limits (E-GSM):	-27.0 thru +41.0

	Limits (DCS1800):	-47.0 thru +33.0

	Limits (PCS1900):	-47.0 thru +33.0

	Default (compatibility mode):	33.0

	Default (GSM900)	13.0

	Default (E-GSM):	13.0

	Default (DCS1800):	10.0

	Default (PCS1900):	10.0

60

Chapter 5

Image 74

Contents HP/Agilent 8922 GSM Hscsd Test System Option #K09 Warranty Limitation of Remedies and Liability Assistance Statement of Compliance Sound Emission Manufacturer’s DeclarationProhibited Earthing ground, incorporated in the power cord. The mainsInstrument dangerous. Intentional interruption is Safety Symbols Safety SymbolsISM 1-A Overview User’s Guide AbbreviationsContents Remote operation Returning equipment for repair Upgrading the HOP Controller ROM and Firmware Understanding the HP/Agilent Getting an overview of the HP/Agilent GSM Hscsd Test System HP/Agilent 8922 GSM Hscsd Test System, option #K09Chapter Features Setting up the HP/Agilent Before you start Checking the HP/Agilent 8922 Requirements for Hscsd Making the front panel connections Front panel connectionsMaking the rear panel connections StepRear panel connections Enabling the Hscsd functionality Inserting the keycard into the HP/AgilentTests screen Conﬁg screen Calibrating the overall system Manual operation Conﬁguring the system Message Frame reset sent appears in the top left-hand corner Establishing a call Measuring BER Making measurementsChoosing which timeslot to measure Changing power levels, timeslot and channels Hscsd control screenEnding a call Ending a call Screens Conﬁg screen Instrument typeChapter Slave address Hscsd screen Master downlink amplitudeSlave offset Master channelSelect ‘Master’ to measure before signalling mobile Master timeslot Slave timeslotCall Type Data rate MeasureMaster Tx level Master input level Master mode Slave Tx levelSlave input level Slave control To Screen menu Peak power displayMobile reports Fast BER Screen Fast BER screenLoopback Remote operation Introduction Conﬁgure Instrument Type comand syntax Conﬁgure Subsystem Gpib CommandsCONFigureINSTrumentTYPE DISPlaySCReen Hscsd Display Subsystem Gpib CommandsDisplay Screen command syntax Hscsd Subsystem Gpib Commands Hscsd command syntax master unit Hscsd command syntax slave unit SYNC? TCHHSCSdMASTerTCHARFCn HSCSdMASTerSTATusTCHTSLot Command 0ptions HSCSdMASTerDOWNlinkAMPLitudeHSCSdMASTerTCHTLEVel HSCSdMASTerUPLinkAMPLitude HSCSdMASTerUPLinkAMPLitudeCONTrol HSCSDMASTerCALLTYPE HSCSDMASTerCALLRATE HSCSdSLAVeSTATusSYNC HSCSdSLAVeSTATusTCHTSLot? HSCSdSLAVeDOWNlinkAMPLitudeOFFSet HSCSdSLAVeTCHTLEVel HSCSdSLAVeUPLinkAMPLitude HSCSdSLAVeUPLinkAMPLitudeCONTrol Remote operating procedures Conﬁguring the systemEstablishing a call Making measurementsChanging channels, timeslot and power levels Ending a call Example code showing a dual-band handover from E-GSM to DCS Clear ScreenPause Example code showing a dual-band handover from E-GSM to DCS Returning equipment for repair Return Procedure Chapter Sales and Service Ofﬁces Canada Sales and Service Ofﬁces Upgrading the HOP Controller ROM and Firmware Upgrading the Hop Controller ROM ROMSide View Figure A-3 Removing the A33 Hop Controller Board Figure A-4 Removing the A33 U62 HOP Controller ROMUpgrading the Hop Controller ROM Upgrading the ﬁrmware