DeWalt Loading the DWFP12569, Before Handling or Operating this Tool, Cleat Loading

Page 6

DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上

LOADING THE DWFP12569

EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI CAN/CSA Z89.1 and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection.

TO PREVENT ACCIDENTAL INJURIES:

•Never place a hand or any other part of the body in nail discharge area of tool while the air supply is connected.

•Never point the tool at anyone else.

•Never engage in horseplay.

•Never actuate the tool unless nose is directed at the work.

•Always handle the tool with care.

•Do not actuate the tool while loading.

DWFP12569

CLEAT LOADING:

Retract pusher until it is in the locked position. Insert a stick of cleats or staples. Push the detent to unlock the pusher. Slide pusher to the fully forward position. The tool is now ready to operate.

NOTE: Use only nails recommended for use in the DWFP12569 nailers or nails which meet the

DEWALT specifications.

BEFORE HANDLING OR OPERATING THIS TOOL:

I.READ AND UNDERSTAND THE WARNINGS CONTAINED IN THIS MANUAL.

II.REFER TO “TOOL SPECIFICATIONS” IN THIS MANUAL TO IDENTIFY THE OPERATING SYSTEM ON YOUR TOOL.

-6-

Page 5 Page 7
Image 6
Page 5 Page 7
Contents DWFP12569 Three Years Limited Warranty Introduction IndexLoading Tool Safety InstructionsAIR Supply and Connections OperationOperating Pressure Fastener SpecificationsTool AIR Fitting AIR ConsumptionLubrication To Prevent Accidental Injuries Loading the DWFP12569Before Handling or Operating this Tool Cleat LoadingAIR SUPPLY-PRESSURE and Volume Replacement PartsAssembly Procedure for Seals Maintaining the Pneumatic ToolMaintaining the DWFP12569 Series Tools To Replace PistonTrouble Shooting Problem Cause CorrectionAccessories Available Introducción Índice NotaGarantía Limitada POR Tres Años Carga DE LA Herramienta Instrucciones DE SeguridadSuministro DE Aire Y Conexiones FuncionamientoConexión DE Aire DE LA Herramienta Especificaciones DE LA Herramienta DWFP12569Especificaciones DEL Sujetador Presión DE OperaciónMantenimiento DE LA Herramienta LubricaciónCarga DE LAS Herramientas Serie F Antes DE Manipular U Operar Esta HerramientaCarga DEL Listón Piezas DE Repuesto Presión Y Volumen DEL Suministro DE AireMantenimiento DE LA Herramienta Neumática Procedimiento DE Ensamblaje Para LOS SellosMantenimiento DE LAS Herramientas DE LA Serie DWFP12569 Para Reemplazar EL PistónSolución DE Problemas Problema CausaCorrección Introduction Sommaire RemarqueGarantie Limitée DE Trois ANS Chargement DE L’OUTIL Instructions DE SécuritéAlimentation EN AIR ET Connexions FonctionnementCaractéristiques DU DWFP12569 OpérationEntretien DE L’APPAREIL LubrificationChargement DES Outils DE LA Série F Chargement DE SauterellesPièces DE Rechange Maintenance DE L’OUTIL PneumatiquePression ET Volume DE L’ALIMENTATION D’AIR Procédure DE Montage DES JointsPour Remplacer LE Piston Pour Remplacer L’ENTRAINEMENTProblème Cause Solution Dépannage
Top Page Image Contents