Woodstock W1688 instruction manual Quick Release Lever, Miter Gauge

Page 17

Jam Nut

Quick Release

Lever

Swivel Assy.

Figure 17. Quick release lever, jam nut, and

swivel assy.

Threaded Lock Knob Hole

Miter Pivot Hole

Figure 18. miter gauge holes in main table.

Miter Lock Knob

Figure 19. Miter gauge installed.

Quick Release Lever

Your Model W1688 Edge Sander is equipped with the quick release lever that allows you to release the tension on the belt for quick belt changing.

To install the quick release lever, do these steps:

1.Loosen the belt tracking lock knob. See

Figure 16.

2.Slide the quick release lever through the platen cover lever slot. See Figure 16.

3.Thread the 1⁄2" jam nut onto the quick release lever until the nut bottoms at the end of the lever threads and thread the lever into the swivel assembly until the lever bottoms. If required have an assistant push the idler roller inward to line up the swivel assembly with the threaded lever. See Figure 17.

4.Tighten the jam nut and the belt tracking lock knob. See Figure 17.

Miter Gauge

The miter gauge is used when sanding the ends of workpieces at least 8" long at various angles.

The miter gauge is not a back stop!

To install the miter gauge, do these steps:

1.Locate the miter gauge pivot hole and the threaded lock-knob hole in the main table. See Figure 18.

NOTICE

The miter gauge pivot pin pivots from one main table location only. Any other hole in the table is not used for the miter gauge.

2.Insert the miter gauge pivot pin located at the underside of the miter gauge into the pivot hole located at the top of the main table.

3.Secure the miter gauge to the table using the miter lock knob as shown in Figure 19.

-15-

ASSEMBLY

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Edge Sander Page Table of Contents About Your New Edge Sander Woodstock Service and SupportIntroduction Specifications Warranty and ReturnsDisconnect machine when cleaning, adjusting or servicing SafetyStandard Safety Instructions Habits-good and bad-are hard to break Keep machine away from open flameKeep fingertips away from the moving sanding belt Additional Safety Instructions for Edge SandersDo not hold wood away from the back Avoiding Potential InjuriesExtension Cords 220V OperationGrounding Typical Nema 5-20 plug and receptacle 110V OperationThis Page Intentionally Left Blank Unpacking AssemblyBox Contents Beginning Shop Preparation CleaningMain Table To install the main table, do these stepsFeet Main table-tilt lock levers and scale Miter Gauge To install the quick release lever, do these stepsQuick Release Lever Sanding Belt To install the sanding belt, do these stepsDust Hood Sanding-belt quick release lever Normal operating position Auxiliary Table To install the auxiliary table, do these stepsBack Stop Vertical Belt Tracking AdjustmentsDiagonal belt tracking Diagonal Belt TrackingPlaten and retaining bolts Platen-to-Roller AlignmentHex nut and belt tension rod Belt TensionMain Table Height To adjust the table height, do these stepsDo not loosen both table tilt lock Levers at the same time Main Table TiltStarting the Sander OperationsIncorrectly holding and tilting Platen Platen TiltingSet the workpiece on the table Vertical SandingOperation Incorrect face sanding away from Back stop Horizontal SandingSet the workpiece on the auxiliary table Contour SandingTroubleshooting Troubleshooting Operation This Page Intentionally Left Blank Lubrication Cleaning MaintenanceGeneral Table and BaseW1688 Edge Sander Wiring Diagram Closure 6450 101 14 65 Description Tilt Plate Your Notes Your Notes BOX BELLINGHAM, WA Warranty Card
Top Page Image Contents