Hitachi WR9DM2, WR12DM2 Installing the bit WH12DM2, WH9DM2, Removing the bit WH12DM2, WH9DM2

Page 19

2.Installing the bit (WH12DM2, WH9DM2)

Always follow the following procedure to install

driver bit. (Fig. 13)

(1)Pull the guide sleeve back.

(2)Insert the bit into the hexagonal hole in the anvil.

(3)Release the guide sleeve and it returns to its origianl position.

CAUTION:

If the guide sleeve does not return to its original position, then the bit is not installed properly.

3.Removing the bit (WH12DM2, WH9DM2)

Please do the opposite point on the method of installing bit.

4.Selecting the socket matched to the bolt (WR12DM2, WR9DM2)

Be sure to use a socket which is matched to the bolt to be tightened. Using an improper socket will not only result in insufficient tightening but also in damage to the socket or nut.

A worn or deformed hex. or square-holed socket will not give an adequate tightness for fitting to the nut or anvil, consequently resulting in loss of tightening torque.

Pay attention to wear of socket hole, and replace before further wear has developed.

Matching socket and bolt sizes are shown Tables 4, 5, 6 and 7. The numerical value of a socket designation denotes the side-to-side distance (H) of its hex. hole.

5.Installing a socket (Fig. 14, 15-1) (WR12DM2)

Align the plunger located in the square part of the anvil with the hole in the hex. socket. Then push the plunger, and mount the hex. socket on the anvil. Check that the plunger is fully engaged in the hole. When removing the socket, reverse the sequence.

6.Retaining ring type (Fig. 14, 15-2) (WR9DM2)

(1) Align the square portions of the socket and the anvil with each other.

(2) Make sure to firmly install the socket by pushing it all the way into the anvil.

(3) When removing the socket, pull it out of the anvil.

CAUTION:

English

Movement

Driver bit

Hexagonal

hole in the Guide

anvil sleeve

Fig. 13

Hexagonal socket Groove Anvil

Fig. 14

Hexagonal

socket Plunger

Hole Anvil

Fig. 15-1

Hexagonal

socket Hole

Anvil

Fig. 15-2

Please use the designated attachments which are listed in the operations manual and Hitachi’s catalog. Accidents or injuries could result from not doing so.

19

Image 19
Contents Advertencia AvertissementContents Meanings of Signal Words Important Safety InformationGeneral Safety Rules for ALL Battery Operated Tools SafetyEnglish Never operate without all guards in place Specific Safety RulesEnglish Important Safety Instructions for Battery Charger Make Them Available to Other Users Owners of this Tool Cordless Impact Driver/Wrench Functional DescriptionModel Name of PartsBattery Charger SpecificationsCordless Impact Driver WR9DM2 WR12DM2 Cordless Impact WrenchApplications Assembly and OperationRemoval and Installation Method of Battery Handle Latch Recharge Insert Able Battery Pull outEnglish RED Before USE Using the light equipped hookOperation English Batteries Rance Hook cover Indentation Selecting the socket matched to the bolt WR12DM2, WR9DM2 Installing the bit WH12DM2, WH9DM2Installing a socket , 15-1 WR12DM2 Removing the bit WH12DM2, WH9DM2Tightening and loosening screws Switch operationNumber of screw tightenings possible WH12DM, WH9DM Resting the unit after continuous work Operational CautionsTightening and loosening bolts Number of bolt tightened possible WR12DM2, WR9DM2Confirm the tightening torque Tightening torqueUse a tightening time suitable for the screw Holding the toolKgf·cm In-lbs 100 1000 For WR12DM2 For WH9DM2Bolt Steel plate Thickness t Nut For WR9DM2⋅ 2-5/32 M16 ⋅ 55 F10T bolt Maintenance and Inspection Check for Dust Disposal of the exhausted battery StorageService and repairs Service parts listStandard Accessories AccessoriesBattery Drill chuck adapter set Code No Phillips bitHexagonal socket Wood working drill bit Code NoWR12DM2, WR9DM2 SocketsLong Socket 9.5 mm Extension bar WR12DM2, WR9DM2Universal joint WR12DM2, WR9DM2 12.7 mmCorner attachment Model EW-14R WR12DM2 Duct socket WR12DM2Mm adapter WR12DM2 Bit adaptor WR12DM2 2 12.7 mm Square adaptor WR9DM2Signification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéConserver CES Instructions SecuriteAvertissement Min Rotations ou mouvements de va-et-vient par minute Regles DE Securite SpecifiquesCourant continu Vitesse à videFrançais Intensité nominale d’entrée CA ampères Français Français Visseuse à percussion à batterie/Clé à choc à batterie Description FonctionnelleModele NOM DES PartiesModèle Chargeur de batterieVisseuse à percussion à batterie OrificeClé à choc à batterie Méthode DE Recharge Méthode DE Retrait ET D’INSTALLATION DE LA BatterieAssemblage ET Fonctionnement UtilisationsFrançais Verte Utilisation Avant L’UTILISATIONUtilisation du crochet avec lampe Français Ne pas trop serrer la vis. Cela pourrait abîmer le filetage Retrait de la mèche WH12DM2, WH9DM2 Mise en place de la mèche WH12DM2Mise in place d’une douille , 15-1 WR12DM2 En appuyant sur le côté L du bouton-poussoir Type de bague de retenue , 15-2 WR9DM2Fonctionnement de l’interrupteur Serrage et desserrage des visSerrage et desserrage des boulon Utiliser le couple de serrage adapté à chaque type de vis Precautions DutilisationRepos de l’appareil après un travail continu Couple de serrageVérifier le couple de serrage Pour WH9DM2 Pour WH12DM2Pour WR9DM2 Pour WR12DM2Boulon Epaisseur de la Plaque d’acier t Ecrou Français Entretien ET Inspection Rangement Remplacement d’un balai en carboneVérifier s’il y a de la poussière Mise au rebut d’une batterie uséeListe des pièces de rechange EB1220BL N de code AccessoiresAccessoires Standard BatterieDouille hexagonale Mèche PhillipsForet pour le forage du bois N de Code Douilles Jeu d’adaptateur de mandrin de foreuse N de CodeUtiliser la foreuse en vente WR12DM2, WR9DM2 Pour WR9DM2 Tableau Douille longue9,5 mm Barre de rallonge WR12DM2, WR9DM2Joint universel WR12DM2, WR9DM2 12,7 mmAdaptateur 9,5 mm WR12DM2 Dimension SDouille à tubulure WR12DM2 Fixation en coin Modèle EW-14R WR12DM2Adaptateur de mèche WR12DM2 Adaptateur carré de 1/2 12,7 mm WR9DM2Cet adaptateur est utilisé pour serrer des petites vis M6 Significado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadGuarde Estas Instrucciones SeguridadAdvertencia Utilice la herramienta correcta Normas Específicos DE SeguridadEspañol 25 7,5 100 150 Español Español Atornillador/Llave de impacto a batería Descripción FuncionalModelo NomenclaturaLa torsión es de pernos 9/16 ModeloVelocidad sin carga 2800/min CapacidadTiempo de carga Aprox min Cargador Tensión de carga Llave de impacto a bateríaCargador de baterías Monofàsica 120 V CA, 60 HzMétodo DE Carga Montaje Y OperaciónAplicaciones Método DE Extracción E Instalación DE LA BateríaLámpara piloto Orificio de instalación de la batería PrecauciónRoja TablaOperación Antes DE LA UtilizaciónEmpleo del gancho equipado con luz El diámetro más grande queda en dirección opuesta Negativo -. Fig InterruptorDe la flecha. Fig Alineélas con las indicaciones del gancho yTipo anillo de retención , 15-2 WR9DM2 Instalación de la punta del atornillador WH12DM2, WH9DM2Extracción de la broca WH12DM2, WH9DM2 Instalacón de un receptáculo , 15-1 WR12DM2Apretado y aflojado de pernos Operación de conmutaciónRPulsador L PresionarPresionar 13. Número posible de aprietes WR12DM2, WR9DM2 11. Número posible de aprietes WH12DM2, WH9DM2Precauciones Operacionales Español Para WH9DM2 Para WH12DM2Para WR9DM2 Para WR12DM2Perno Tuerca Grosor de la plancha de acero t Completamente descargado Mantenimiento de motor Mantenimiento E InspecciónComprobación de las condiciones de la broca WH12DM2, WH9DM2 Comprobación de los tornillosAlmacenamiento Reemplazar el carbón de contactoComprobación del polvo Eliminación de las baterías agotadasModificaciones Lista de repuestosUC14YF21 AccesoriosAccesorios Estándar WH12DM2, WH9DM2 1. BateríaReceptáculo hexagonal para tuercas y pernos Broca PhillipsBroca para taladrar madera Nº de código WR12DM2, WR9DM2 1. Battería Juego adaptador de portabrocas Nº de códigoCubos Para WR9DM2 Tabla Cubo largoJunta cardánica WR12DM2, WR9DM2 Barra de extensión WR12DM2, WR9DM2Nº de código Dimensión B, S Modelo Accesorio para esquinas Modelo EW-14R WR12DM2 Cubo para conductos WR12DM2Adaptador de 9,5 mm WR12DM2 Adaptador de brocas WR12DM2 Adaptador rectangular de 1/2 12,7 mm WR9DM21R D2 2M 107 Kestrel Road Mississauga on L5T 1Z5