Grizzly G1033X owner manual Cleanup, Before cleaning, gather the following

Page 15

Cleanup

The unpainted surfaces of your machine are coated with a heavy-duty rust preventative that prevents corrosion during shipment and storage.

This rust preventative has been your machine's close ally and guardian since it left the factory. If your machine arrived to you free of rust, then be thankful that the rust preventative protected it during its journey...and try to stay thankful as you clean it off, because it can be challenging to remove if you are unprepared and impatient.

Plan on spending some time cleaning your machine. The time you spend doing this will reward you with smooth sliding parts and a better appreciation for the proper care of your machine's unpainted surfaces.

Although there are many ways to successfully remove the rust preventative, these instructions walk you through what works well for us.

Before cleaning, gather the following:

Disposable Rags

Cleaner/degreaser (see below)

Safety glasses & disposable gloves

H9692—Orange Power Cleaner & Degreaser One of the best cleaners we've found for quickly and easily removing rust preventative.

Figure 4. Model H9692 Industrial Orange Power

Cleaner/Degreaser (99.9% biodegradable).

Note: In a pinch, automotive degreasers, mineral spirits or WD•40 can be used to remove rust pre- ventative. Before using these products, though, test them on an inconspicuous area of your paint to make sure they will not damage it.

Model G1033X (Mfg. since 4/10)

Gasoline and petroleum products have low flash points and can explode or cause fire if used to clean machinery. Avoid using these products to clean machinery.

Many cleaning solvents are toxic if inhaled. Minimize your risk by only using these products in a well ventilated area.

NOTICE

Avoid chlorine-based solvents, such as acetone or brake parts cleaner that may damage painted surfaces. Always follow the manufacturer’s instructions when using any type of cleaning product.

Basic steps for removing rust preventative:

1.Put on safety glasses and disposable gloves.

2.Coat all surfaces that have rust preventative with a liberal amount of your cleaner/degreas- er and let them soak for few minutes.

3.Wipe off the surfaces. If your cleaner/degreas- er is effective, the rust preventative will wipe off easily.

Note: To clean off thick coats of rust preven- tative on flat surfaces, such as tables, use a PLASTIC paint scraper to scrape off the majority of the coating before wiping it off with your rag. (Do not use a metal scraper or you may scratch your machine.)

4.Repeat Steps 2–3as necessary until clean, then coat all unpainted surfaces with a quality metal protectant to prevent rust.

-13-

Image 15
Contents Model G1033X 20 5HP Spiral Cutterhead Planer Page Table of Contents Introduction Manual AccuracyContact Info Identification Machine Data Sheet Cutterhead Info Safety Instructions for Machinery SafetyMany machines can eJect wOrKpieces tOward OperatOr Use a GrOunded pOwer supply rated FOr the machine amperaGeKeep children/visitOrs away Maintain machinery with care.­Additional Safety for Planers Unplugging during adjustmentsRemoving jammed workpieces Circuit Requirements 220V Single-PhaseDescription Qty SET UPItems Needed for Set Up UnpackingBox Inventory Figure Qty InventoryHardware Recognition Chart Before cleaning, gather the following CleanupSite Considerations Weight LoadTo attach the table extension wings Moving & Placing PlanerExtension Wings Components and Hardware Needed QtyTo install the handwheel HandwheelDust Hood Gearbox Oil Level Connecting to Power Test RunTo check the gearbox oil level Tighten V-Belts Recommended AdjustmentsOperation Safety Basic Operation OperationsBasic steps of operating the planer are as follows Feed Speed Operation TipsAdjustment Height Range 002-0.020 Tools Needed Qty To adjust the bed rollersBed Rollers G7315Z-Heavy-Duty Shop FOX Mobile Base AccessoriesH4978 T20446 H4979 H9893-Replacement Inserts 10 PackBelts MaintenanceCleaning ScheduleTension screw locations LubricationTroubleshooting ServiceCutting Rotating/Changing Carbide Cutters Tools Needed QtyTo rotate or change a carbide cutter Maximum Allowable Tolerances To adjust the chain tensionChain Tension Table ParallelismChain Tension instructions on Table Parallelism InspectionDistance Below Cutter Edge at *BDC Internal Component HeightsAdjusting chip breaker height Model G1033X Mfg. since 4/10 Planer Spring Tension To adjust feed roller spring tensionChip Deflector Gap Setting To adjust the deflector positionScale Calibration Anti-Kickback FingersTo calibrate the scale Should you find that the pulleys are out of alignment Pulley AlignmentElectrical Components Motor Junction Box Control Panel Magnetic SwitchMagnetic Switch Wiring DiagramHeadstock Parts Breakdown Description Headstock Parts ListChip Breaker Table Parts Breakdown Table Parts List 120 Stand/Motor Parts BreakdownStand/Motor Parts List 217 204 209 208 211 214 219 215 207 218 203 210 206 205 Labels & CosmeticComments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns Warranty and ReturnsOrder Hours a DAY