Grizzly G1033X owner manual Maintenance, Schedule, Cleaning, Belts

Page 26

SECTION 6: MAINTENANCE

Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious person- al injury.

Schedule

For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructions given in this section.

Daily:

•Clean unpainted cast iron part of table

•Lubricate feed rollers

Weekly Maintenance:

•Clean cutterhead

•Lubricate four columns

Monthly Check:

•Inspect V-belt tension, damage, or wear

•Clean/vacuum dust buildup from inside cabi- net and off motor

•Lubricate worm gear

•Lubricate chain

•Lubricate drive chain

Yearly:

•Change gear box oil (should be performed after the first 20 hours when planer is new).

Cleaning

Vacuum excess wood chips and sawdust, and wipe off the remaining dust with a dry cloth—this ensures moisture from wood dust does not remain on bare metal surfaces. Treat all unpainted cast iron and steel with a non-staining lubricant after cleaning. We recommend products like SLIPIT®, G96® Gun Treatment, or Boeshield® T-9 (see Page 21 for more details).

-24-

V-Belts

V-belt removal and replacement is simply a mat- ter of loosening the V-belts, rolling them off of the pulleys, replacing them with new belts, then retensioning them.

Always replace V-belts with a matched set of 3 belts, or belt tension may not be even among the 3 belts and may cause premature belt failure.

Consider replacing stock belts with Power Twist V-belts (see Page 21) to reduce vibration and noise, and increase belt lifespan.

To adjust/replace belts the V-belts:

1.DISCONNECT THE PLANER FROM THE POWER SOURCE!

2.Open the motor access panel and V-belt cover.

3.Using a 19mm wrench, loosen the fasteners on the tension rods shown in Figure 23.

Figure 23. Fasteners needed to be loosened for

V-belt replacement.

4.Lift the motor up and slide the V-belts off of the pulleys.

5.Slide the new belts onto the pulley, lower the motor, and tighten the fasteners loosened in

Step 3.

Model G1033X (Mfg. since 4/10)

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Model G1033X 20 5HP Spiral Cutterhead Planer Page Table of Contents Contact Info IntroductionManual Accuracy Identification Machine Data Sheet Cutterhead Info Safety Safety Instructions for MachineryMaintain machinery with care.­ Use a GrOunded pOwer supply rated FOr the machine amperaGeKeep children/visitOrs away Many machines can eJect wOrKpieces tOward OperatOrRemoving jammed workpieces Additional Safety for PlanersUnplugging during adjustments 220V Single-Phase Circuit RequirementsUnpacking SET UPItems Needed for Set Up Description QtyInventory Box Inventory Figure QtyHardware Recognition Chart Cleanup Before cleaning, gather the followingWeight Load Site ConsiderationsComponents and Hardware Needed Qty Moving & Placing PlanerExtension Wings To attach the table extension wingsDust Hood To install the handwheelHandwheel To check the gearbox oil level Gearbox Oil Level Connecting to PowerTest Run Recommended Adjustments Tighten V-BeltsBasic steps of operating the planer are as follows Operation Safety Basic OperationOperations Operation Tips Feed SpeedBed Rollers Adjustment Height Range 002-0.020 Tools Needed QtyTo adjust the bed rollers Accessories G7315Z-Heavy-Duty Shop FOX Mobile BaseH9893-Replacement Inserts 10 Pack H4978 T20446 H4979Schedule MaintenanceCleaning BeltsLubrication Tension screw locationsService TroubleshootingCutting To rotate or change a carbide cutter Rotating/Changing Carbide CuttersTools Needed Qty Table Parallelism To adjust the chain tensionChain Tension Maximum Allowable TolerancesTable Parallelism Inspection Chain Tension instructions onInternal Component Heights Distance Below Cutter Edge at *BDCAdjusting chip breaker height Model G1033X Mfg. since 4/10 Planer To adjust the deflector position To adjust feed roller spring tensionChip Deflector Gap Setting Spring TensionTo calibrate the scale Scale CalibrationAnti-Kickback Fingers Pulley Alignment Should you find that the pulleys are out of alignmentMotor Junction Box Control Panel Magnetic Switch Electrical ComponentsWiring Diagram Magnetic SwitchHeadstock Parts Breakdown Headstock Parts List DescriptionChip Breaker Table Parts Breakdown Table Parts List Stand/Motor Parts Breakdown 120Stand/Motor Parts List Labels & Cosmetic 217 204 209 208 211 214 219 215 207 218 203 210 206 205Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns Warranty and ReturnsOrder Hours a DAY
Top Page Image Contents