Grizzly G1033X owner manual Bed Rollers, Adjustment Height Range 002-0.020 Tools Needed Qty

Page 23

Bed Rollers

Adjustment Height Range

0.002"–0.020"

Tools Needed:

Qty

Hex Wrench 3mm

1

Open End Wrench 14mm

1

Rotacator (optional, Page 21)

1

The height of the bed rollers will vary, depend- ing on the type of material you intend to plane, but as a general rule keep the roller height within 0.002"–0.020" above the table. When planing rough stock, set the rollers high to keep the lum- ber from dragging along the bed. When planing milled lumber, set the rollers low to help minimize snipe.

Table

0.002"–0.020"

 

 

Roller

Figure 13. Bed roller height range.

To ensure accurate results and make the adjust- ment process quicker and easier, we recommend using a Rotacator (see Page 21) to gauge the bed roller height from the table. If a Rotacator is not available, a straightedge and feeler gauges can be used, but extra care must be taken to achieve satisfactory results.

Note: Misaligned bed rollers can cause workpiece chatter, a washboard surface, uneven workpiece feeding, or binding.

To adjust the bed rollers:

1.Lower the table to give yourself at least 4" of working room below the cutterhead.

2.Loosen the locking set screws (Figure 14) above the roller adjusters (4 total).

Roller

Locking

Set Screw

Adjuster

 

Figure 14. Bed roller controls (only one side

shown).

3.Raise or lower the rollers by rotating the adjusters to reach your desired height.

4.Verify both sides of the bed roller are at the same height and lock them in position with the locking set screws.

5.Double check the roller heights to make sure they did not move when you locked them (if they did, repeat the procedure).

Model G1033X (Mfg. since 4/10)

-21-

Image 23
Contents Model G1033X 20 5HP Spiral Cutterhead Planer Page Table of Contents Contact Info IntroductionManual Accuracy Identification Machine Data Sheet Cutterhead Info Safety Instructions for Machinery SafetyMany machines can eJect wOrKpieces tOward OperatOr Use a GrOunded pOwer supply rated FOr the machine amperaGeKeep children/visitOrs away Maintain machinery with care.­Removing jammed workpieces Additional Safety for PlanersUnplugging during adjustments Circuit Requirements 220V Single-PhaseDescription Qty SET UPItems Needed for Set Up UnpackingBox Inventory Figure Qty InventoryHardware Recognition Chart Before cleaning, gather the following CleanupSite Considerations Weight LoadTo attach the table extension wings Moving & Placing PlanerExtension Wings Components and Hardware Needed QtyDust Hood To install the handwheelHandwheel To check the gearbox oil level Gearbox Oil Level Connecting to PowerTest Run Tighten V-Belts Recommended AdjustmentsBasic steps of operating the planer are as follows Operation Safety Basic OperationOperations Feed Speed Operation TipsBed Rollers Adjustment Height Range 002-0.020 Tools Needed QtyTo adjust the bed rollers G7315Z-Heavy-Duty Shop FOX Mobile Base AccessoriesH4978 T20446 H4979 H9893-Replacement Inserts 10 PackBelts MaintenanceCleaning ScheduleTension screw locations LubricationTroubleshooting ServiceCutting To rotate or change a carbide cutter Rotating/Changing Carbide CuttersTools Needed Qty Maximum Allowable Tolerances To adjust the chain tensionChain Tension Table ParallelismChain Tension instructions on Table Parallelism InspectionDistance Below Cutter Edge at *BDC Internal Component HeightsAdjusting chip breaker height Model G1033X Mfg. since 4/10 Planer Spring Tension To adjust feed roller spring tensionChip Deflector Gap Setting To adjust the deflector positionTo calibrate the scale Scale CalibrationAnti-Kickback Fingers Should you find that the pulleys are out of alignment Pulley AlignmentElectrical Components Motor Junction Box Control Panel Magnetic SwitchMagnetic Switch Wiring DiagramHeadstock Parts Breakdown Description Headstock Parts ListChip Breaker Table Parts Breakdown Table Parts List 120 Stand/Motor Parts BreakdownStand/Motor Parts List 217 204 209 208 211 214 219 215 207 218 203 210 206 205 Labels & CosmeticComments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns Warranty and ReturnsOrder Hours a DAY