Grizzly G1033X owner manual Internal Component Heights, Distance Below Cutter Edge at *BDC

Page 33

7.Repeat Steps 4–6with each sprocket that needs to be adjusted until the table-to- cutterhead clearance is within 0.016" from one side to the other.

8.Make sure the chain is properly fitted on the sprockets, and tighten the idler sprocket and lock bolts.

9.Micro-adjust the table position by loosening the cap screws shown in Figure 30 and lifting the table upward or downward until the table and cutterhead are in alignment.

Note: This process may require adjusting the columns on both the left and right hand sides until you find the correct combination.

Figure 30. Table micro-adjustment screws.

Model G1033X (Mfg. since 4/10)

Internal Component

Heights

Distance Below Cutter Edge at *BDC
Infeed Roller	0.040"
Chip Breaker	0.040"
Pressure Bar	0.040"
Outfeed Roller	0.040"
Tools Needed:	Qty
Hex Wrench 3mm	1
Hex Wrench 5mm	1
Wrench or Socket 10mm	1
Rotacator (optional, Page 21)	1

*BDC = Bottom Dead Center (see Figure 31).

Bottom Dead

Center

Figure 31. Carbide insert at bottom dead center

To ensure accurate results and make the adjust- ment process quicker and easier, we recommend using a Rotacator (see Page 21) for these adjust- ments.

If a Rotacator is not available, a 6' 2x4 cut into two even sized pieces and a 0.40" feeler gauge can be used, but care must be taken when jointing the blocks to achieve accurate results.

To set the height of the infeed and outfeed rollers, chip breaker, and pressure bar using a Rotacator:

1.Disconnect the planer from the power source!

-31-

Image 33

Contents Model G1033X 20 5HP Spiral Cutterhead Planer Page Table of Contents Introduction Manual AccuracyContact Info Identification Machine Data Sheet Cutterhead Info Safety Instructions for Machinery SafetyKeep children/visitOrs away Use a GrOunded pOwer supply rated FOr the machine amperaGeMaintain machinery with care. Many machines can eJect wOrKpieces tOward OperatOrAdditional Safety for Planers Unplugging during adjustmentsRemoving jammed workpieces Circuit Requirements 220V Single-PhaseItems Needed for Set Up SET UPUnpacking Description QtyBox Inventory Figure Qty InventoryHardware Recognition Chart Before cleaning, gather the following CleanupSite Considerations Weight LoadExtension Wings Moving & Placing PlanerComponents and Hardware Needed Qty To attach the table extension wingsTo install the handwheel HandwheelDust Hood Gearbox Oil Level Connecting to Power Test RunTo check the gearbox oil level Tighten V-Belts Recommended AdjustmentsOperation Safety Basic Operation OperationsBasic steps of operating the planer are as follows Feed Speed Operation TipsAdjustment Height Range 002-0.020 Tools Needed Qty To adjust the bed rollersBed Rollers G7315Z-Heavy-Duty Shop FOX Mobile Base AccessoriesH4978 T20446 H4979 H9893-Replacement Inserts 10 PackCleaning MaintenanceSchedule BeltsTension screw locations LubricationTroubleshooting ServiceCutting Rotating/Changing Carbide Cutters Tools Needed QtyTo rotate or change a carbide cutter Chain Tension To adjust the chain tensionTable Parallelism Maximum Allowable TolerancesChain Tension instructions on Table Parallelism InspectionDistance Below Cutter Edge at *BDC Internal Component HeightsAdjusting chip breaker height Model G1033X Mfg. since 4/10 Planer Chip Deflector Gap Setting To adjust feed roller spring tensionTo adjust the deflector position Spring TensionScale Calibration Anti-Kickback FingersTo calibrate the scale Should you find that the pulleys are out of alignment Pulley AlignmentElectrical Components Motor Junction Box Control Panel Magnetic SwitchMagnetic Switch Wiring DiagramHeadstock Parts Breakdown Description Headstock Parts ListChip Breaker Table Parts Breakdown Table Parts List 120 Stand/Motor Parts BreakdownStand/Motor Parts List 217 204 209 208 211 214 219 215 207 218 203 210 206 205 Labels & CosmeticComments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns Warranty and ReturnsOrder Hours a DAY