Grizzly G1033X owner manual Keep children/visitOrs away, Maintain machinery with care.­

Page 9

­

safety instructions for machinery

7.Only allOw trained and prOp- erly supervised persOnnel tO Operate machinery.­ Make­ sure­ operation­instructions­are­safe­and­clearly­ understood.

8.Keep children/visitOrs away.

Keep­ all­ children­ and­ visitors­ away­ from­ machinery.­ When­ machine­ is­ not­ in­ use,­ disconnect­ it­ from­ power,­ lock­ it­ out,­ or­ disable­ the­ switch­ to­ make­ it­ difficult­ for­ unauthorized­people­to­start­the­machine.

9.unattended OperatiOn. Leaving­ machine­ unattended­ while­ its­ running­ greatly­increases­the­risk­of­an­accident­or­ property­damage.­Turn­machine­off­and­ allow­ all­ moving­ parts­ to­ come­ to­ a­ com- plete­stop­before­walking­away.

10.dO nOt use in danGerOus envirOnments. DO­ NOT­ use­ machin- ery­ in­ damp,­ wet­ locations,­ or­ where­ any­ flammable­or­noxious­fumes­may­exist.­

11.Keep wOrK area clean and well liGhted. Clutter­and­dark­shadows­may­ cause­accidents.

12.use a GrOunded pOwer supply rated FOr the machine amperaGe.

Grounded­ cords­ minimize­ shock­ hazards.­ Operating­machine­on­an­incorrect­size­of­ circuit­increases­risk­of­fire.

13.always discOnnect FrOm pOwer sOurce BeFOre servicinG machinery.­Make­sure­switch­is­in­ OFF­ position­before­reconnecting.

14.maintain machinery with care.­

Keep­blades­sharp­and­clean­for­best­and­

safest­performance.­Follow­instructions­for­

lubricating­and­changing­accessories.

15.maKe sure Guards are in place and wOrK cOrrectly BeFOre usinG machinery.

16.remOve chucK Keys Or adJustinG tOOls.­ Make­ a­ habit­ of­ never­ leaving­ chuck­keys­or­other­adjustment­tools­in/on­ the­machine—especially­near­spindles!

17.damaGed machinery.­Check­for­bind- ing­ or­ misaligned­ parts,­ broken­ parts,­ loose­ bolts,­ other­ conditions­ that­ may­ impair­machine­operation.­Always­repair­or­ replace­damaged­parts­before­operation.

18.dO nOt FOrce machinery.­ Work­ at­ the­speed­for­which­the­machine­or­acces- sory­was­designed.

19.secure wOrKpiece.­ Use­ clamps­ or­ a­ vise­ to­ hold­ the­ workpiece­ when­ practi- cal.­ A­ secured­ workpiece­ protects­ your­ hands­and­frees­both­hands­to­operate­the­ machine.

20.dO nOt Overreach.­Maintain­ stability­ and­ balance­ at­ all­ times­ when­ operating­ machine.

21.many machines can eJect wOrKpieces tOward OperatOr.

Know­and­avoid­conditions­that­cause­the­

workpiece­to­"kickback."

22.staBle machine. Machines­ that­ move­ during­ operations­ greatly­ increase­ the­ risk­ of­ injury­ and­ loss­ of­ control.­ Verify­ machines­ are­ stable/secure­ and­ mobile­ bases­(if­used)­are­locked­before­starting.

23.certain dust may Be hazardOus­ to­ the­ respiratory­ systems­ of­ people­ and­ animals,­especially­fine­dust.­Be­aware­of­ the­ type­ of­ dust­ you­ are­ exposed­ to­ and­ always­wear­a­respirator­designed­to­filter­ that­type­of­dust.

24.eXperiencinG diFFiculties. If­ at­ any­ time­ you­ are­ experiencing­ difficulties­ performing­ the­ intended­ operation,­ stop­ using­ the­ machine!­ Contact­ our­ Technical­ Support­Department­at­(570)­546-9663.

Model G1033X (Mfg. since 4/10)

-7-

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Model G1033X 20 5HP Spiral Cutterhead Planer Page Table of Contents Introduction Manual AccuracyContact Info Identification Machine Data Sheet Cutterhead Info Safety Instructions for Machinery SafetyKeep children/visitOrs away Use a GrOunded pOwer supply rated FOr the machine amperaGeMaintain machinery with care.­ Many machines can eJect wOrKpieces tOward OperatOrAdditional Safety for Planers Unplugging during adjustmentsRemoving jammed workpieces Circuit Requirements 220V Single-PhaseItems Needed for Set Up SET UPUnpacking Description QtyBox Inventory Figure Qty InventoryHardware Recognition Chart Before cleaning, gather the following CleanupSite Considerations Weight LoadExtension Wings Moving & Placing PlanerComponents and Hardware Needed Qty To attach the table extension wingsTo install the handwheel HandwheelDust Hood Gearbox Oil Level Connecting to Power Test RunTo check the gearbox oil level Tighten V-Belts Recommended AdjustmentsOperation Safety Basic Operation OperationsBasic steps of operating the planer are as follows Feed Speed Operation TipsAdjustment Height Range 002-0.020 Tools Needed Qty To adjust the bed rollersBed Rollers G7315Z-Heavy-Duty Shop FOX Mobile Base AccessoriesH4978 T20446 H4979 H9893-Replacement Inserts 10 PackCleaning MaintenanceSchedule BeltsTension screw locations LubricationTroubleshooting ServiceCutting Rotating/Changing Carbide Cutters Tools Needed QtyTo rotate or change a carbide cutter Chain Tension To adjust the chain tensionTable Parallelism Maximum Allowable TolerancesChain Tension instructions on Table Parallelism InspectionDistance Below Cutter Edge at *BDC Internal Component HeightsAdjusting chip breaker height Model G1033X Mfg. since 4/10 Planer Chip Deflector Gap Setting To adjust feed roller spring tensionTo adjust the deflector position Spring TensionScale Calibration Anti-Kickback FingersTo calibrate the scale Should you find that the pulleys are out of alignment Pulley AlignmentElectrical Components Motor Junction Box Control Panel Magnetic SwitchMagnetic Switch Wiring DiagramHeadstock Parts Breakdown Description Headstock Parts ListChip Breaker Table Parts Breakdown Table Parts List 120 Stand/Motor Parts BreakdownStand/Motor Parts List 217 204 209 208 211 214 219 215 207 218 203 210 206 205 Labels & CosmeticComments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns Warranty and ReturnsOrder Hours a DAY
Top Page Image Contents