Grizzly G1033X owner manual Planer

Page 35

To adjust the height of the infeed and outfeed rollers, chip breaker and pressure bar using wood blocks and a feeler gauge:

1.Build the wood blocks by cutting a STRAIGHT 6' long 2x4 in half.

Note: Having the wood blocks at an even height is critical to the accuracy of your over- all adjustments. For best results, remove board warpage by squaring the 2x4 with a jointer and table saw before cutting in half.

2.Disconnect the planer from the power source!

3.Lower the bed rollers below the table.

4.Place one wood block along the left side of the table, and place the other wood block along the right side of the table, as illustrated in Figure 36.

36"

20" PLANER

Figure 36. Wood blocks on table.

5.Remove the dust port, top cover, and belt cover.

6.Adjust the table and use the feeler gauge until you have a 0.040" gap between the edge of a carbide insert at bottom dead center (find by rocking cutterhead pulley) and the wood blocks.

7.Lock the table height in place, as the wood blocks will now be your reference points for the rest of the adjustments.

8.Loosen the infeed roller adjustment jam nuts (Figure 33) and turn the adjustment set screws on each end to raise the feed roller above the wood block (if necessary), then bring it back down so it just touches the wood block on both sides.

9.Lock the infeed roller adjustment set screws in place with the jam nuts, making sure they do not move while tightening.

10.Without moving the table, adjust the chip breaker (Figure 35), pressure bar (Figure 34), and outfeed roller (Figure 33) in the same manner, using the wood blocks as your reference point.

11.When you are finished with the adjustments, replace the top cover, dust port, and belt cover.

Model G1033X (Mfg. since 4/10)

-33-

Image 35
Contents Model G1033X 20 5HP Spiral Cutterhead Planer Page Table of Contents Contact Info IntroductionManual Accuracy Identification Machine Data Sheet Cutterhead Info Safety Instructions for Machinery SafetyMany machines can eJect wOrKpieces tOward OperatOr Use a GrOunded pOwer supply rated FOr the machine amperaGeKeep children/visitOrs away Maintain machinery with care.­Removing jammed workpieces Additional Safety for PlanersUnplugging during adjustments Circuit Requirements 220V Single-PhaseDescription Qty SET UPItems Needed for Set Up UnpackingBox Inventory Figure Qty InventoryHardware Recognition Chart Before cleaning, gather the following CleanupSite Considerations Weight LoadTo attach the table extension wings Moving & Placing PlanerExtension Wings Components and Hardware Needed QtyDust Hood To install the handwheelHandwheel To check the gearbox oil level Gearbox Oil Level Connecting to PowerTest Run Tighten V-Belts Recommended AdjustmentsBasic steps of operating the planer are as follows Operation Safety Basic OperationOperations Feed Speed Operation TipsBed Rollers Adjustment Height Range 002-0.020 Tools Needed QtyTo adjust the bed rollers G7315Z-Heavy-Duty Shop FOX Mobile Base AccessoriesH4978 T20446 H4979 H9893-Replacement Inserts 10 PackBelts MaintenanceCleaning ScheduleTension screw locations LubricationTroubleshooting ServiceCutting To rotate or change a carbide cutter Rotating/Changing Carbide CuttersTools Needed Qty Maximum Allowable Tolerances To adjust the chain tensionChain Tension Table ParallelismChain Tension instructions on Table Parallelism InspectionDistance Below Cutter Edge at *BDC Internal Component HeightsAdjusting chip breaker height Model G1033X Mfg. since 4/10 Planer Spring Tension To adjust feed roller spring tensionChip Deflector Gap Setting To adjust the deflector positionTo calibrate the scale Scale CalibrationAnti-Kickback Fingers Should you find that the pulleys are out of alignment Pulley AlignmentElectrical Components Motor Junction Box Control Panel Magnetic SwitchMagnetic Switch Wiring DiagramHeadstock Parts Breakdown Description Headstock Parts ListChip Breaker Table Parts Breakdown Table Parts List 120 Stand/Motor Parts BreakdownStand/Motor Parts List 217 204 209 208 211 214 219 215 207 218 203 210 206 205 Labels & CosmeticComments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns Warranty and ReturnsOrder Hours a DAY