Grizzly G1033X owner manual Lubrication, Tension screw locations

Page 27

6.Close the V-belt cover and motor access panel.

Note: The correct tension for the V-belts is 1⁄4" deflection when pushed in the center with moder- ate pressure. After the first 16 hours of belt life, retension them, as they will stretch and seat dur- ing this time.

Gear Box: Gear box oil should be changed after the first 20 hours of operation (see Figure 24).

Replace with 80W-90W gear oil. Inspect levels periodically and change yearly. Replace gear oil more frequently under heavy use. Fill until oil reaches the top of the filler plug port for correct oil level.

Lubrication

The Model G1033X features factory-sealed bear- ings. A sealed bearing requires no lubrication during its lifetime. Should a bearing fail, your planer will probably develop a noticeable rumble/ vibration, which will increase when the machine is put under load. Bearings are standard sizes and can be replaced through Grizzly.

Proper lubrication of other planer components are essential for long life and trouble-free operation. Below is a list of components that require periodic lubrication. Schedules are based on daily use. Adjust accordingly for your level of use.

Always disconnect power to the machine before lubricating! Failure to do this may result in serious personal injury.

Columns/Lead Screws: The four columns should be lubricated weekly with SAE 30W oil. Unfasten dust covers to gain access. The four lead screws should be lubricated with general purpose grease once a month.

Worm Gear: The worm gear should be inspected monthly and lubricated with general purpose grease when needed. Remove the worm gear box to inspect. See parts diagram for location.

Chain: The table height adjustment chain (see Figure 27 on Page 28) should be inspected monthly and lubricated with general purpose grease when needed.

Model G1033X (Mfg. since 4/10)

Fill

Drain

Figure 24. Gearbox oil drain/fill locations.

Drive Chain: The drive chain should be inspected and lubricated monthly. Check sprocket, chain and cotter pin during inspection. Use a general purpose grease. Some chains will have master links instead of cotter pins.

Feed Rollers: Regular lubrication of feed rollers is crucial to the operation of your planer. Lubricate every 30 hours of use. Each end of each power feed roller has an oiling port located on the top of the head casting (Figure 25). Apply SAE 30W oil, making sure that the lubricant penetrates the bearing.

Figure 25. Tension screw locations.

-25-

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Model G1033X 20 5HP Spiral Cutterhead Planer Page Table of Contents Introduction Manual AccuracyContact Info Identification Machine Data Sheet Cutterhead Info Safety Instructions for Machinery SafetyMany machines can eJect wOrKpieces tOward OperatOr Use a GrOunded pOwer supply rated FOr the machine amperaGeKeep children/visitOrs away Maintain machinery with care.­Additional Safety for Planers Unplugging during adjustmentsRemoving jammed workpieces Circuit Requirements 220V Single-PhaseDescription Qty SET UPItems Needed for Set Up UnpackingBox Inventory Figure Qty InventoryHardware Recognition Chart Before cleaning, gather the following CleanupSite Considerations Weight LoadTo attach the table extension wings Moving & Placing PlanerExtension Wings Components and Hardware Needed QtyTo install the handwheel HandwheelDust Hood Gearbox Oil Level Connecting to Power Test RunTo check the gearbox oil level Tighten V-Belts Recommended AdjustmentsOperation Safety Basic Operation OperationsBasic steps of operating the planer are as follows Feed Speed Operation TipsAdjustment Height Range 002-0.020 Tools Needed Qty To adjust the bed rollersBed Rollers G7315Z-Heavy-Duty Shop FOX Mobile Base AccessoriesH4978 T20446 H4979 H9893-Replacement Inserts 10 PackBelts MaintenanceCleaning ScheduleTension screw locations LubricationTroubleshooting ServiceCutting Rotating/Changing Carbide Cutters Tools Needed QtyTo rotate or change a carbide cutter Maximum Allowable Tolerances To adjust the chain tensionChain Tension Table ParallelismChain Tension instructions on Table Parallelism InspectionDistance Below Cutter Edge at *BDC Internal Component HeightsAdjusting chip breaker height Model G1033X Mfg. since 4/10 Planer Spring Tension To adjust feed roller spring tensionChip Deflector Gap Setting To adjust the deflector positionScale Calibration Anti-Kickback FingersTo calibrate the scale Should you find that the pulleys are out of alignment Pulley AlignmentElectrical Components Motor Junction Box Control Panel Magnetic SwitchMagnetic Switch Wiring DiagramHeadstock Parts Breakdown Description Headstock Parts ListChip Breaker Table Parts Breakdown Table Parts List 120 Stand/Motor Parts BreakdownStand/Motor Parts List 217 204 209 208 211 214 219 215 207 218 203 210 206 205 Labels & CosmeticComments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns Warranty and ReturnsOrder Hours a DAY
Top Page Image Contents