Bosch Power Tools 275T6, 285T6, 395T6 Step Operating Instructions, Collet and Accessory Assembly

Page 13

DM 2610925474 10-04 10/19/04 3:40 PM Page 13

STEP 2

STEP 3

 

 

 

 

 

 

Step 2. Unscrew the housing cap from the tool. Step 3. Remove the collet.

Note: If the collet nut and collet are not removed from the motor shaft, the tool will not function properly.

STEP 4

OPERATING INSTRUCTIONS

Disengagement of the Flex-Shaft

The flexible shaft may become disengaged if the motor of your rotary tool is not elevated higher than the working end of the flex-shaft. The #2222 Rotary Tool Stand is recommended to hold the rotary tool at the proper height.

Collet and Accessory Assembly

The collet assembly consists of a collet nut and collet. Take the collet nut and collet that were removed from your tool in step 2 and 3 and insert them into the tip of the flex-shaft handpiece.

Step 4. Install the driver cap on the motor shaft and tighten.

To prevent damage to tool, do ! CAUTION not overtighten driver cap.

Tighten the driver cap finger tight and then tighten an additional 1/3 turn with the wrench. (Wrench included with your rotary tool kit)

STEP 5

Step 5. Attach by screwing the collar of the flex-shaft to the rotary tool. Make sure the square end of the center core engages the square hole socket in the driver cap.

Do not pull out center core to ! CAUTION engage into driver cap. This

could cause disengagement of center core from handpiece. If tool stops when shaft is bent, center core may be lodged in driver cap. Loosen shaft and remove core from driver cap. Then screw flexible shaft onto rotary tool housing again.

Insert an accessory or bit as deeply as possible to avoid wobble during use. With the shaft lock button engaged on the flex-shaft handpiece retighten the collet nut.

Collet Removal and Replacement

Four different size collets to accommodate different shank sizes, are sold separately for your flex-shaft. To install a different collet, remove the collet nut and remove the old collet. Insert the unslotted end of the collet in the hole in the end of the flex-shaft. Replace collet nut on the shaft. Always use the collet which matches the shank size of the accessory you plan to use. Never force a larger diameter shank into a collet.

FLEXIBLE SHAFT LUBRICATION — The flexible shaft should be lubricated after every 25-30 hours of use. To lubricate, unscrew the flexible shaft assembly from the motor housing. Pull the center core out of the flexible shaft assembly. Wipe a very thin film of a good quality, high temperature grease on to the center core.

To prevent damage to tool do not ! CAUTION over grease shaft. Too much

grease will cause the unit to overheat. Dremel shaft lubricant No. 5990952 or automotive wheel bearing grease should be used.

Reattach the flex-shaft to the rotary tool.

Page 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Models 275T6 F013027503 285T6 F013028503 395T6 F013039504 MultiProElectrical Safety Power Tool Safety RulesPersonal Safety Work AreaService Safety Rules for Rotary ToolsSanding, sawing, grinding Some dust created by powerSymbols Rotary Tool 275T6 & 285T6 Functional Description and SpecificationsRotary Tool 395T6 Cutting Guide Flex-ShaftRight Angle Attachment Collet Identification Chart AssemblyRotary Tool is running Dremel Keyless ChuckSharpen Tools Operating InstructionsShape Wood Carve Wood Deburr Metal Using the Rotary Tool Questions or Problems?CallFlow and causes the motor to overheat Operating Speeds Switch SettingNeeds for Slower Speeds Speed RangeInstallation Instructions Assembly & Operation of AttachmentsLet speed do the work KickbackCollet Removal and Replacement Collet and Accessory AssemblyStep Operating Instructions Disengagement of the Flex-ShaftFor use in drywall DescriptionFor use on wall tile, cement board and plaster Not for USE on Floor TileTo set cutting depth Cleaning Grout Grout Removal Attachment Cutting Depth AdjustmentGrout Removal Kit Removing Grout to Replace a Broken TileOperating Instructions Prolong usage Right Angle AttachmentCleaning Maintenance InformationCurved END of Brush Must Match Curvature Housing Spring Extension CordsDremel Attachments Dremel Accessories Polishing Accessories Wire BrushesSanding Accessories Bristle BrushesDrywall Cutting Bit Cutting WheelsTile Cutting Bit Spiral Cutting BitDM 2610925474 10-04 10/19/04 340 PM Depending on cutting direction relative to grain Use only Dremel Tested, High Performance AccessoriesSpeed for light cuts, caution burning on deep grooves Speed Settings Drill BIT Modèles 275T6 F013027503 285T6 F013028503 395T6 F013039504 MultiPro Outil Rotatif Manuel de l’utilisateurConservez CES Instructions Règles de Sécurité GénéralesRéparation Consignes de sécurité pour outils rotatifsQue ponçage, sciage Consignes de sécurité pour outils rotatifs suiteNOM SymbolesOutil Rotatif 275T6, 285T6 Description fonctionnelle et spécificationsOutil Rotatif 395T6 Arbre flexible Accessoire à angle droit565 Nécessaire Universel de coupeMandrin Sans CLÉ AssemblageMandrin Sans CLÉ Dremel Affûtage des outils Consignes d’utilisationQuestions ou problèmes ? Composez le Consignes d’utilisation suiteUtilisation du Outil Rotatif Nécessité de vitesses plus lentes Vitesses de fonctionnementPlage de vitesses Directives D’INSTALLATION Assemblage et fonctionnement des accessoiresLarbre flexible Laissez la vitesse faire le travailDirectives D’USAGE Enlèvement et remplacement du morsDébranchement de l’arbre Flex-Shaft Ne tirez pas sur l’arbreSil présente un coude Le guide de coupeNE PAS Utiliser SUR LES Carreaux Céramiques DE Planchers Pour régler la profondeur de coupe Nettoyage du coulis Kit pour l’extraction de coulisMode d’emploi Assemblage et Fonctionnement des Accessoires’une utilisation prolongée Dentraînement SerrerEntretien Renseignements sur l’entretienNettoyage RallongesAccessoire toupie Accessoires DremelArbre flexible 566 Nécessaire de coupe de céramiqueMandrins DouillesCouteaux à grande vitesse Couteaux au carbure de tungstèneAccessoires de ponçage Accessoires de polissageBrosses métalliques Brosses en soie de porcAccessoires Dremel suite Avertissement Selon le sens de coupe par rapport au grain du bois Réglages DE VitesseAcier Réglages DE Vitesse ÉTATS-UNIS Garantie limitée de DremelCanada ’EXTÉRIEUR DU Territoire Continental DES ÉTATS-UNISDM 2610925474 10-04 10/19/04 340 PM Modelos 275T6 F013027503 285T6 F013028503 395T6 F013039504 Manual del usuario MultiPro Herramienta GiratoriaConserve Estas Instrucciones Normas de seguridad para herramientas mecánicasServicio Normas de seguridad para herramientas giratoriasNormas de seguridad para herramientas giratorias De Ni-Cd SímbolosHerramienta Giratoria 275T6, 285T6 Descripción funcional y especificacionesHerramienta Giratoria 395T6 Juego de Eje flexibleCortadores multiuso Accesorio de ángulo rectoBoton DE Fijacion DEL EJE Llave DE Portaherramienta EnsamblajeCuadro DE Identificacion DE Portaherra Mandril DE Apriete SIN Llave DremelAfilar herramientas Instrucciones de utilizaciónDar forma a madera Desbarbar metal Tallar madera Cortar Consejos de funcionamiento ¿Preguntas o problemas? Llame alUtilización de la Herramienta Giratoria Bloquea el flujo de aire y hace que el motor se recalienteNecesidades de velocidades más lentas Velocidades de funcionamientoIntervalo de velocidad ¡Deje que la velocidad haga el trabajo Montaje y funcionamiento de los aditamentosInstrucciones Para LA Instalación PasoInstrucciones Para Operar La guía de corte Montaje y Funcionamiento de los AccesoriosRadio DE 127 mm No Para Utilizar CON Cerámica DE PisoCómo ajustar la profundidad de corte Al Limpiar Lechada Juego para quitar lechadaAdvertencias de Seguridad para la Remoción de Lechada Aditamento en ángulo recto Servicio Información de mantenimientoLimpieza Cordones de extensiónEje flexible Aditamentos para DremelAditamento de fresadora Columna para taladroAccesorios para la Dremel Presión de cepillado Cepillos de cerdaAccesorios para pulir Ruedas abrasivas de óxido de aluminioBrocas de fresadora de alta velocidad Ruedas de corteBroca de corte en espiral Broca para cortar pared de tipo secoAdvertencia Posiciones DE Velocidad Ceramica Accesorios Para Pulir Zona Poniente Aguascalientes Distrito FederalChihuahua Zona Centro CoahuilaNuevo Leon Guerrero MorelosJalisco OaxacaTamaulipas Tabasco YucatanQuintana ROO QueretaroEstados Unidos Garantía limitada DremelCanada Fuera DE LOS Territorios DM 2610925474 10-04 10/19/04 340 PM Models Modèles Modelos Numero DE Pieza Description Descripcion NO. DE LA PieceCode no Model NO. DE Code Modèle Modelo Description DescripcionDescription Descripcion Dremel Cutting GuideCompression Spring Resorte Ressort Description DescripcionDM 2610925474 10-04 10/19/04 340 PM DM 2610925474 10-04 10/19/04 340 PM Twenty-First StreetOR Racine, Wisconsin 53406 Dremel Limited WarrantyCanada Outside

275T6, 285T6, 395T6 specifications

Bosch Power Tools has long been a trusted name for professionals and DIY enthusiasts alike, and the models 275T6, 285T6, and 395T6 demonstrate the brand's commitment to innovation, durability, and high performance. Each of these tools is meticulously designed to cater to various applications while delivering efficiency and reliability.

The Bosch 275T6 is a versatile tool that embodies power and precision. This corded electric tool features a robust motor that delivers exceptional torque and speed, making it ideal for heavy-duty tasks. One of its standout features is the variable speed control, allowing users to customize operation according to the material being worked on. Additionally, its ergonomic design ensures comfort during prolonged use, minimizing user fatigue. The 275T6 also incorporates advanced safety features, including a lock-on switch that prevents accidental activation and a protective housing that extends the tool's lifespan.

Next in line is the Bosch 285T6, which takes versatility a step further. This model is equipped with an innovative multi-functional design, allowing it to perform a variety of tasks, from drilling to sanding. Noteworthy is its quick-change chuck system, which enables users to switch between accessories with ease and efficiency. The 285T6 also features an integrated LED light that illuminates work areas, making it particularly useful in low-light conditions. Its lightweight construction does not compromise on durability, ensuring it can withstand rigorous use without hassle.

Finally, the Bosch 395T6 is designed for those who demand the highest performance under extreme conditions. This model boasts a heavy-duty motor that is optimized for high torque applications, making it perfect for demanding jobs in both wood and metal. The 395T6 incorporates tooth-tipped technology, enhancing cutting efficiency and prolonging blade life. In terms of user experience, the tool incorporates anti-vibration technology, which significantly reduces vibrations during operation, promoting stability and precision.

In summary, Bosch Power Tools' 275T6, 285T6, and 395T6 models are excellent choices for anyone in need of reliable and powerful tools. They come equipped with features that enhance user comfort, safety, and versatility. The combination of premium materials and innovative technology ensures these tools stand out in any toolbox, offering a robust solution for a wide range of applications. With Bosch, users can be assured of quality that translates into outstanding performance.
Top Page Image Contents