Bosch Power Tools 275T6, 285T6, 395T6 Assembly, Rotary Tool is running, Dremel Keyless Chuck

Page 8

DM 2610925474 10-04 10/19/04 3:39 PM Page 8

Assembly

Always unplug Rotary Tool ! WARNING before changing accessories,

changing collets or servicing your Rotary Tool.

SHAFT LOCK

BUTTON

COLLET

WRENCH

TO TIGHTEN

COLLET

NUT

TO LOOSEN

COLLET

 

COLLET NUT — To loosen, first press shaft lock button and rotate the shaft by hand until the lock engages the shaft preventing further rotation.

!

CAUTION

Do not engage lock while the

Rotary Tool is running.

 

 

With the shaft lock engaged use the collet wrench to loosen the collet nut if necessary. The collet nut must be loosely threaded on when inserting an accessory. Change accessories by inserting the new one into the collet as far as possible to minimize runout and unbalance. With the shaft lock engaged, finger tighten the collet nut until the accessory shank is gripped by the collet. Avoid excessive tightening of the collet nut when there is no bit inserted.

COLLETS — Four different size collets (see illus- tration), to accommodate different shank sizes, are available for your Rotary Tool. To install a different collet, remove the collet nut and remove the old collet. Insert the unslotted end of the collet in the hole in the end of the tool shaft. Replace collet nut on the shaft.

Always use the collet which ! CAUTION matches the shank size of the

accessory you plan to use. Never force a larger diameter shank into a collet.

Note: Some rotary tool kits may not include all four collets sizes.

BALANCING ACCESSORIES — For precision work, it is important that all accessories be in good balance (much the same as the tires on your automobile). To true up or balance an accessory, slightly loosen collet nut and give the accessory or collet a 1/4 turn. Re- tighten collet nut and run the Rotary Tool. You should be able to tell by the sound and feel if your accessory is running in balance. Continue adjusting in this fashion until best balance is achieved. To maintain balance on abrasive wheel points, before each use, with the wheel point secured in the collet, turn on the

COLLET IDENTIFICATION CHART

Collet sizes can be identified by the rings on the back end of collet.

1/32" Collet has one (1) ring. 1/16" Collet has two (2) rings. 3/32" Collet has three (3) rings. 1/8" Collet has no rings.

KEYLESS CHUCK

COLLET NUT

 

 

IDENTIFICATION

 

 

RINGS

 

 

 

480

 

 

 

1/8"

 

 

 

481

 

483

COLLET

 

3/32"

482

 

1/32"

 

COLLET

 

1/16"

COLLET

 

 

 

 

COLLET

Rotary Tool and run the 415 Dressing Stone lightly against the revolving wheel point. This removes high spots and trues up the wheel point for good balance.

The hanger is provided for the use of hanging your tool while using the flex-shaft or for storage. If you do not use the hanger, remove it from the tool and snap it back into place underneath the cord so it will be out of the way while the tool is in use.

DREMEL KEYLESS CHUCK

Use only with black chuck #4486. Other chucks may

! CAUTION

not allow accessory bit to be tightened fully.

The keyless chuck holds various accessories with shank sizes 1/32" to 1/8" and is intended for light duty accessories such as drill bits, sanding drums, polishing accessories, wire and bristle brushes and cut-off wheels. The keyless chuck allows you to change accessories frequently, quickly and easily. There are some applications which can generate high forces on the bit or if you are unable to generate finger tightening pressure sufficient to secure the bit you must use the supplied wrench to assist in securing the bit.

Attaching the Keyless Chuck and Accessory Bit

Read and understand the manual for use of the

keyless chuck with the tool. ! WARNING Insert and securely tighten the

shank of the accessory well within the jaws of the chuck. If an accessory is not properly gripped within the jaws of a chuck it may loosen and fly out during

Page 8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents MultiPro Models 275T6 F013027503 285T6 F013028503 395T6 F013039504Power Tool Safety Rules Electrical SafetyPersonal Safety Work AreaSafety Rules for Rotary Tools ServiceSome dust created by power Sanding, sawing, grinding Symbols Rotary Tool 395T6 Functional Description and SpecificationsRotary Tool 275T6 & 285T6 Right Angle Attachment Flex-ShaftCutting Guide Assembly Collet Identification ChartRotary Tool is running Dremel Keyless ChuckShape Wood Carve Wood Deburr Metal Operating InstructionsSharpen Tools Flow and causes the motor to overheat Questions or Problems?CallUsing the Rotary Tool Switch Setting Operating SpeedsNeeds for Slower Speeds Speed RangeAssembly & Operation of Attachments Installation InstructionsLet speed do the work KickbackCollet and Accessory Assembly Collet Removal and ReplacementStep Operating Instructions Disengagement of the Flex-ShaftDescription For use in drywallFor use on wall tile, cement board and plaster Not for USE on Floor TileGrout Removal Attachment Cutting Depth Adjustment To set cutting depth Cleaning GroutGrout Removal Kit Removing Grout to Replace a Broken TileOperating Instructions Right Angle Attachment Prolong usageMaintenance Information CleaningCurved END of Brush Must Match Curvature Housing Spring Extension CordsDremel Attachments Dremel Accessories Wire Brushes Polishing AccessoriesSanding Accessories Bristle BrushesCutting Wheels Drywall Cutting BitTile Cutting Bit Spiral Cutting BitDM 2610925474 10-04 10/19/04 340 PM Speed for light cuts, caution burning on deep grooves Use only Dremel Tested, High Performance AccessoriesDepending on cutting direction relative to grain Speed Settings Drill BIT MultiPro Outil Rotatif Manuel de l’utilisateur Modèles 275T6 F013027503 285T6 F013028503 395T6 F013039504Règles de Sécurité Générales Conservez CES InstructionsConsignes de sécurité pour outils rotatifs RéparationConsignes de sécurité pour outils rotatifs suite Que ponçage, sciageSymboles NOMOutil Rotatif 395T6 Description fonctionnelle et spécificationsOutil Rotatif 275T6, 285T6 Accessoire à angle droit Arbre flexible565 Nécessaire Universel de coupeMandrin Sans CLÉ Dremel AssemblageMandrin Sans CLÉ Consignes d’utilisation Affûtage des outilsUtilisation du Outil Rotatif Consignes d’utilisation suiteQuestions ou problèmes ? Composez le Plage de vitesses Vitesses de fonctionnementNécessité de vitesses plus lentes Assemblage et fonctionnement des accessoires Directives D’INSTALLATIONLarbre flexible Laissez la vitesse faire le travailEnlèvement et remplacement du mors Directives D’USAGEDébranchement de l’arbre Flex-Shaft Ne tirez pas sur l’arbreNE PAS Utiliser SUR LES Carreaux Céramiques DE Planchers Le guide de coupeSil présente un coude Kit pour l’extraction de coulis Pour régler la profondeur de coupe Nettoyage du coulisAssemblage et Fonctionnement des Accessoires Mode d’emploiDentraînement Serrer ’une utilisation prolongéeRenseignements sur l’entretien EntretienNettoyage RallongesAccessoires Dremel Accessoire toupieArbre flexible 566 Nécessaire de coupe de céramiqueDouilles MandrinsCouteaux à grande vitesse Couteaux au carbure de tungstèneAccessoires de polissage Accessoires de ponçageBrosses métalliques Brosses en soie de porcAccessoires Dremel suite Avertissement Réglages DE Vitesse Selon le sens de coupe par rapport au grain du boisAcier Réglages DE Vitesse Garantie limitée de Dremel ÉTATS-UNISCanada ’EXTÉRIEUR DU Territoire Continental DES ÉTATS-UNISDM 2610925474 10-04 10/19/04 340 PM Manual del usuario MultiPro Herramienta Giratoria Modelos 275T6 F013027503 285T6 F013028503 395T6 F013039504Normas de seguridad para herramientas mecánicas Conserve Estas InstruccionesNormas de seguridad para herramientas giratorias ServicioNormas de seguridad para herramientas giratorias Símbolos De Ni-CdHerramienta Giratoria 395T6 Descripción funcional y especificacionesHerramienta Giratoria 275T6, 285T6 Eje flexible Juego deCortadores multiuso Accesorio de ángulo rectoEnsamblaje Boton DE Fijacion DEL EJE Llave DE PortaherramientaCuadro DE Identificacion DE Portaherra Mandril DE Apriete SIN Llave DremelDar forma a madera Desbarbar metal Tallar madera Cortar Instrucciones de utilizaciónAfilar herramientas ¿Preguntas o problemas? Llame al Consejos de funcionamientoUtilización de la Herramienta Giratoria Bloquea el flujo de aire y hace que el motor se recalienteIntervalo de velocidad Velocidades de funcionamientoNecesidades de velocidades más lentas Montaje y funcionamiento de los aditamentos ¡Deje que la velocidad haga el trabajoInstrucciones Para LA Instalación PasoInstrucciones Para Operar Montaje y Funcionamiento de los Accesorios La guía de corteRadio DE 127 mm No Para Utilizar CON Cerámica DE PisoJuego para quitar lechada Cómo ajustar la profundidad de corte Al Limpiar LechadaAdvertencias de Seguridad para la Remoción de Lechada Aditamento en ángulo recto Información de mantenimiento ServicioLimpieza Cordones de extensiónAditamentos para Dremel Eje flexibleAditamento de fresadora Columna para taladroAccesorios para la Dremel Cepillos de cerda Presión de cepilladoAccesorios para pulir Ruedas abrasivas de óxido de aluminioRuedas de corte Brocas de fresadora de alta velocidadBroca de corte en espiral Broca para cortar pared de tipo secoAdvertencia Posiciones DE Velocidad Ceramica Accesorios Para Pulir Aguascalientes Distrito Federal Zona PonienteChihuahua Zona Centro CoahuilaGuerrero Morelos Nuevo LeonJalisco OaxacaTabasco Yucatan TamaulipasQuintana ROO QueretaroCanada Fuera DE LOS Territorios Garantía limitada DremelEstados Unidos DM 2610925474 10-04 10/19/04 340 PM Models Modèles Modelos NO. DE LA Piece Numero DE Pieza Description DescripcionCode no Model NO. DE Code Modèle Modelo Description DescripcionDremel Cutting Guide Description DescripcionDescription Descripcion Compression Spring Resorte RessortDM 2610925474 10-04 10/19/04 340 PM DM 2610925474 10-04 10/19/04 340 PM Dremel Limited Warranty Twenty-First StreetOR Racine, Wisconsin 53406Canada Outside
Top Page Image Contents