DeWalt D25013 instruction manual Overload Clutch, Drilling Tools, Drilling Fig

Page 10

English

Overload Clutch

If the drill bit becomes jammed or caught, the drive to the drill spindle is interrupted by the overload clutch. Because of the forces that occur as a result, always hold the machine securely with both hands and take a firm stance.

Drilling Tools

The machine is intended for hammerdrilling in concrete, brick and stone. It is also suitable for drilling without impact in wood, metal, ceramic and plastic.

Drilling (Fig. 1)

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/installing attachments or accessories.

WARNING: To reduce the risk of personal injury, ALWAYS

ensure workpiece is anchored or clamped firmly. If drilling thin material, use a wood “back-up” block to prevent damage to the material.

Press mode selector button (F) and turn the mode selector (G) to the drill bit symbol for drilling, to the hammer symbol for hammering or to the hammerdrill symbol for hammerdrilling.

DRILLING OPERATION

1.For WOOD, use twist bits, spade bits, power auger bits or hole saws. For METAL, use high-speed steel twist drill bits or hole saws. Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry. For MASONRY, use carbide-tipped bits or masonry bits. A smooth, even flow of dust indicates the proper drilling rate.

2.Always apply pressure in a straight line with the bit. Use enough pressure to keep the drill bit biting, but do not push hard enough to stall the motor or deflect the bit.

3.Hold tool firmly with both hands to control the twisting action of the drill.

WARNING: Drill may stall if overloaded causing a sudden twist. Always expect the stall. Grip the drill firmly with both hands to control the twisting action and avoid injury.

4. IF DRILL STALLS, it is usually because it is being overloaded. RELEASE TRIGGER IMMEDIATELY, remove drill bit from work, and determine cause of stalling. DO NOT CLICK

TRIGGER OFF AND ON IN AN ATTEMPT TO START A STALLED DRILL – THIS CAN DAMAGE THE DRILL.

5.To minimize stalling or breaking through the material, reduce pressure on drill and ease the bit through the last fractional part of the hole.

6.Keep the motor running when pulling the bit back out of a drilled hole. This will help prevent jamming.

7.With variable speed drills there is no need to center punch the point to be drilled. Use a slow speed to start the hole and accelerate by squeezing the trigger harder when the hole is deep enough to drill without the bit skipping out.

DRILLING IN METAL

An SDS Plus® to round shank adaptor chuck is required. Ensure that tool is in drill-only mode. Start drilling with slow speed and increase to full power while applying firm pressure on the tool. A smooth even flow of metal chips indicates the proper drilling rate. Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry.

NOTE: Large [5/16" to 1/2" (7.9 mm to 12.7 mm)] holes in steel can be made easier if a pilot hole [5/32" to 3/16" (4 mm to 4.8 mm)] is drilled first.

DRILLING IN WOOD

An SDS Plus® to round shank adaptor chuck is required. Ensure that tool is in drill-only mode. Start drilling with slow speed and increase to full power while applying firm pressure on the tool. Holes in wood

8

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Page Page Work Area Safety Definitions Safety GuidelinesGeneral Power Tool Safety Warnings Electrical SafetyPower Tool USE and Care Additional Safety Instructions for Rotary HammersService Voltage Volts Total length of cord in meters m Motor Components Fig Assembly and AdjustmentsSide Handle Fig Reversing Lever Fig Trigger Switch FigMode Selector Fig Variable SpeedOperation SDS-plusChuck FigProper Hand Position Fig Drilling Tools Overload ClutchDrilling Fig Chipping and Chiselling MaintenanceCleaning Depth Rod FigLubrication AccessoriesRepairs Seguridad DEL Área DE Trabajo Definiciones Normas De seguridadSeguridad Eléctrica Seguridad Personal USO Y Mantenimiento DE LA Herramienta EléctricaMantenimiento Ténsion Volts Longitud del cable en metros m Descripción FIG Mango lateral Fig Montaje Y AjustesInterruptor de gatillo Fig Velocidad Variable Palanca de reversa FigSelector de modo Fig Botón DE Bloqueo EN Encendido Sólo CON D25013Funcionamiento Broquero/mandril SDS Plus FigBien colocar las manos Fig Taladrado Embrague de sobrecargaTaladros Fig Funcionamiento DE TaladradoCincelado Varilla de profundidad FigLubricación MantenimientoLimpieza AccesoriosRegras Gerais de Segurança Definições Diretrizes de SegurançaGuarde Estas Instruções USO E Cuidados DA Ferramenta Instruções de segurança adicionais para marteletes rotativos ReparosTensão Comprimento do cabo de extensão Componentes Fig Empunhadura lateral Fig Montagem E AjustesInterruptor tipo gatilho Fig Velocidade Variável Alavanca de reversão FigBotão DE Trava Como Operar a Ferramenta Seletor de modo FigMandril SDS-plusFig Como segurar corretamente a ferramenta FigPerfuração Fig Limitador de torqueFerramentas de perfuração Operação DE PerfuraçãoRompedor Barra de profundidade FigLubrificação ManutençãoLimpeza AcessóriosCapacidade Ótima ReparosEspecificações D25013
Top Page Image Contents