Hitachi DH 30PC, DH 30PB instruction manual Switch operation, Rotation + Striking, Rotation only

Page 13

1.Switch operation

The rotation speed of the drill bit can be controlled steplessly by varying the amount that the trigger switch is pulled. Speed is low when the trigger switch is pulled slightly and increases as the switch is pulled more.

2.Rotation + Striking

This rotary hammer can be set to

rotation and striking mode by pressing the push button and turning the

change lever to mark. (Fig. 5)

(1)Mount the drill bit.

(2)Pull the trigger switch after applying the drill bit tip to the drilling position (Fig. 6)

(3)Pushing the rotary hammer forcibly is not necessary at all. Pushing slightly so that drill dust comes out gradually is just sufficient.

CAUTION:

◯When the drill bit touches an iron reinforcing rod, the bit will stop immediately and the rotary hammer will react to revolve. Therefore please grip the side handle and handle tightly as shown in Fig. 6.

3.Rotation only

This rotary hammer can be set to rotation only mode by pressing the

push button and turning the change

lever to mark. (Fig. 7)

To drill a wood or metal material using the separately sold drill chuck and chuck adaptor, proceed as follows. Installing drill chuck and chuck adaptor (Fig. 8):

(1)Mount the drill chuck to the chuck adaptor.

(2)The part of the SDS-plus shank is the same as the drill bit. Therefore, refer to the item of “Mounting the drill bit” for attaching it.

English

Push

Button

Change

Lever

Fig. 5

Fig. 6

Push Button

Change

Lever

Fig. 7

Front Cap Grip

Drill

Chuck

	Chuck	Part of SDS-plus
	Adaptor	Part of SDS-plus
	Adaptor	shank
		shank
		Fig. 8

13

Image 13

Contents Advertencia AvertissementContents Meanings of Signal Words Important Safety InformationGeneral Safety Rules SafetyEnglish Never operate without all guards in place Specific Safety Rules and SymbolsBlades and accessories must be securely mounted to the tool Double Insulation for Safer Operation Make Them Available to Other Users Owners of this ToolFunctional Description SpecificationsName of Parts Applications Assembly and OperationPrior to Operation Collector B Optional accessories Installation of dust cup or dustConfirming condition of the environment Mounting the drill bit FigSelecting the function mode HOW to USESelecting the driver bit Rotation + Striking Switch operationRotation only When driving wood screws Fig When driving machine screws FigStriking only DH30PC Using the stopper FigUsing the side handle HOW to USE the Core BIT for Light LoadDismounting. Fig How to bore FigMaintenance of the motor Maintenance and InspectionInspecting the drill bits Inspecting the screwsService and repairs How to replase greasePage Page Page Page Page Page Signification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéRegles Generale DE Securite SecuriteConserver CES Instructions Français NE Jamais toucher les parties mobiles Regles DE Securite Specifiques ET SymbolesUtiliser l’outil correct Ne pas essuyer les parties en plastique avec du solvant Double Isolation Pour UN Fonctionnement Plus SUR NOM DES Parties Description FonctionnelleSource d’alimentation Avant L’UTILISATIONInterrupteur d’alimentation Cordon prolongateurMontage du foret de perçage Fig Vérification des conditions d’environnementSélection de la mèche pour visseuse Sélection du mode de fonctionFonctionnement de l’interrupteur UtilisationRotation + frappe Rotation seulement Enfoncement de vis à bois Fig Lors du vissage des vis machine FigUtilisation de l’arràtoir Fig Percussion uniquement DH30PCMontage Utilisation de la poignée latéraleDémontage Fig Perçage FigInspection des vis Contrôle du foret de perçageEntretien du moteur Contrôle des balais en carbone FigEntretien et reparation Comment remplacer la graisseFrançais Page Page Page Page Page Significado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadNormas Generales DE Seguridad SeguridadGuarde Estas Instrucciones Español Normas Y Símbolos Específicos DE Seguridad No toque Nunca las piezas móviles Maneje con cuidado las herramientas eléctricas Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Nomenclatura Descripción FuncionalEspecificaciones Aplicaciones Montaje Y OperaciónAntes DE LA Operación Montaje de la broca Fig Confirme las condiciones del medio ambienteSelección de la broca destornillador Como SE USASelección del modo de función Rotación + golpeteo Operación del conmutadorRotación solamente Español Percusión solamente DH30PC Atornillando tornillos para madera FigModo de usar el tope Fig Uso del asa lateral Modo DE Usar LA Barrena Tubularpara Cargas LigerasModo de taladrar Fig MontajeDesmontaje Fig Inspeccionar la broca de taladro Mantenimiento E InspecciónInspección de los tornillos Mantenimiento de motorMantenimiento y reparación Cambio de grasaPage Page Page Page Page Page Hitachi Koki Canada Co