Hitachi DH 30PC, DH 30PB instruction manual Striking only DH30PC, Using the stopper Fig

Page 15

English

CAUTION:

◯Exercise care in preparing a pilot hole suitable for the wood screw taking the hardness of the wood into consideration. Should the hole be excessively small or shallow, requiring much power to drive the screw into it, the thread of the wood screw may sometimes be damaged.

6.Striking only (DH30PC)

This rotary hammer can be set to striking only mode by pressing the push button and turning the change

lever to mark. (Fig. 10)

(1)Mount the bull point or cold chisel.

(2)Press the push button and set the

change lever to mark or mark. Then rotation is released, turn the grip

and adjust the cold chisel to desired position. (Fig. 11)

(3)Turn the change lever to mark. (Fig. 10)

Then bull point or cold chisel is locked.

7. Using the stopper (Fig. 12)

(1)Loosen the side handle, and insert the stopper into the handle bolt hole.

(2)Adjust the stopper position according to the depth of the hole and tighten the side handle securely.

8.How to use the drill bit (taper shank) and the taper shank

adaptor.

(1)Mount the taper shank adaptor to the rotary hammer. (Fig. 13)

(2)Mount the drill bit (taper shank) to the taper shank adaptor. (Fig. 13)

(3)Turn the switch ON, and drill a hole in prescribed depth.

(4)To remove the drill bit (taper shank), insert the cotter into the slot of the taper shank adaptor and strike the head of the cotter with a manual hammer supporting on the rests. (Fig. 14)

Change Lever

Push Button

Fig. 10

Grip

Fig. 11

Handle Bolt

Knob on Side

Stopper Handle

Fig. 12

15

Image 15

Contents Advertencia AvertissementContents Meanings of Signal Words Important Safety InformationGeneral Safety Rules SafetyEnglish Never operate without all guards in place Specific Safety Rules and SymbolsBlades and accessories must be securely mounted to the tool Double Insulation for Safer Operation Make Them Available to Other Users Owners of this ToolSpecifications Functional DescriptionName of Parts Assembly and Operation ApplicationsPrior to Operation Mounting the drill bit Fig Installation of dust cup or dustCollector B Optional accessories Confirming condition of the environmentHOW to USE Selecting the function modeSelecting the driver bit Switch operation Rotation + StrikingRotation only When driving wood screws Fig When driving machine screws FigStriking only DH30PC Using the stopper FigUsing the side handle HOW to USE the Core BIT for Light LoadDismounting. Fig How to bore FigInspecting the screws Maintenance and InspectionMaintenance of the motor Inspecting the drill bitsService and repairs How to replase greasePage Page Page Page Page Page Signification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéSecurite Regles Generale DE SecuriteConserver CES Instructions Français NE Jamais toucher les parties mobiles Regles DE Securite Specifiques ET SymbolesUtiliser l’outil correct Ne pas essuyer les parties en plastique avec du solvant Double Isolation Pour UN Fonctionnement Plus SUR NOM DES Parties Description FonctionnelleCordon prolongateur Avant L’UTILISATIONSource d’alimentation Interrupteur d’alimentationMontage du foret de perçage Fig Vérification des conditions d’environnementSélection de la mèche pour visseuse Sélection du mode de fonctionUtilisation Fonctionnement de l’interrupteurRotation + frappe Rotation seulement Enfoncement de vis à bois Fig Lors du vissage des vis machine FigUtilisation de l’arràtoir Fig Percussion uniquement DH30PCMontage Utilisation de la poignée latéraleDémontage Fig Perçage FigContrôle des balais en carbone Fig Contrôle du foret de perçageInspection des vis Entretien du moteurEntretien et reparation Comment remplacer la graisseFrançais Page Page Page Page Page Significado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadSeguridad Normas Generales DE SeguridadGuarde Estas Instrucciones Español Normas Y Símbolos Específicos DE Seguridad No toque Nunca las piezas móviles Maneje con cuidado las herramientas eléctricas Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Descripción Funcional NomenclaturaEspecificaciones Montaje Y Operación AplicacionesAntes DE LA Operación Montaje de la broca Fig Confirme las condiciones del medio ambienteComo SE USA Selección de la broca destornilladorSelección del modo de función Operación del conmutador Rotación + golpeteoRotación solamente Español Atornillando tornillos para madera Fig Percusión solamente DH30PCModo de usar el tope Fig Uso del asa lateral Modo DE Usar LA Barrena Tubularpara Cargas LigerasModo de taladrar Fig MontajeDesmontaje Fig Mantenimiento de motor Mantenimiento E InspecciónInspeccionar la broca de taladro Inspección de los tornillosMantenimiento y reparación Cambio de grasaPage Page Page Page Page Page Hitachi Koki Canada Co