Hitachi DH 30PC, DH 30PB instruction manual How to bore Fig, Dismounting. Fig

Page 17

Fig. 18

English

(4)Engage the guide plate with the core bit, and turn the guide plate to left or right so that it does not fall even if it faced downward. (Fig. 17)

Guide Plate

Center Pin	Core Bit Tip

Core Bit

Fig. 16

Fig. 17

2. How to bore (Fig. 18)

(1)Connect the plug to the power source.

(2)A spring is installed in the center pin.

Push it lightly to the wall or the floor perpendicularly. Connect all over the surface of the core bit tip and start operating.

(3) When boring about 3/16" (5 mm) in depth the position of the hole will establish. Bore after that removing the center pin and the guide plate from core bit.

(4)Application of excessive force will not only expedite the work, but will deteriorate the tip edge of the drill bit, resulting in reduced service life of the rotary hammer.

CAUTION:

◯When removing the center pin and the guide plate, turn OFF the switch and disconnect the plug form the receptacle.

3.Dismounting. (Fig. 19)

Remove the core bit shank from the rotary hammer and strike the head of the core bit shank strongly two or three times with the manual hammer holding the core bit, then the thread becomes loose and the core bit can be removed.

Core Bit shank

Fig. 19

17

Image 17

Contents Advertencia AvertissementContents Meanings of Signal Words Important Safety InformationGeneral Safety Rules SafetyEnglish Never operate without all guards in place Specific Safety Rules and SymbolsBlades and accessories must be securely mounted to the tool Double Insulation for Safer Operation Make Them Available to Other Users Owners of this ToolName of Parts SpecificationsFunctional Description Prior to Operation Assembly and OperationApplications Collector B Optional accessories Installation of dust cup or dustConfirming condition of the environment Mounting the drill bit FigSelecting the driver bit HOW to USESelecting the function mode Rotation only Switch operationRotation + Striking When driving wood screws Fig When driving machine screws FigStriking only DH30PC Using the stopper FigUsing the side handle HOW to USE the Core BIT for Light LoadDismounting. Fig How to bore FigMaintenance of the motor Maintenance and InspectionInspecting the drill bits Inspecting the screwsService and repairs How to replase greasePage Page Page Page Page Page Signification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéConserver CES Instructions SecuriteRegles Generale DE Securite Français NE Jamais toucher les parties mobiles Regles DE Securite Specifiques ET SymbolesUtiliser l’outil correct Ne pas essuyer les parties en plastique avec du solvant Double Isolation Pour UN Fonctionnement Plus SUR NOM DES Parties Description FonctionnelleSource d’alimentation Avant L’UTILISATIONInterrupteur d’alimentation Cordon prolongateurMontage du foret de perçage Fig Vérification des conditions d’environnementSélection de la mèche pour visseuse Sélection du mode de fonctionRotation + frappe UtilisationFonctionnement de l’interrupteur Rotation seulement Enfoncement de vis à bois Fig Lors du vissage des vis machine FigUtilisation de l’arràtoir Fig Percussion uniquement DH30PCMontage Utilisation de la poignée latéraleDémontage Fig Perçage FigInspection des vis Contrôle du foret de perçageEntretien du moteur Contrôle des balais en carbone FigEntretien et reparation Comment remplacer la graisseFrançais Page Page Page Page Page Significado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadGuarde Estas Instrucciones SeguridadNormas Generales DE Seguridad Español Normas Y Símbolos Específicos DE Seguridad No toque Nunca las piezas móviles Maneje con cuidado las herramientas eléctricas Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Especificaciones Descripción FuncionalNomenclatura Antes DE LA Operación Montaje Y OperaciónAplicaciones Montaje de la broca Fig Confirme las condiciones del medio ambienteSelección del modo de función Como SE USASelección de la broca destornillador Rotación solamente Operación del conmutadorRotación + golpeteo Español Modo de usar el tope Fig Atornillando tornillos para madera FigPercusión solamente DH30PC Uso del asa lateral Modo DE Usar LA Barrena Tubularpara Cargas LigerasModo de taladrar Fig MontajeDesmontaje Fig Inspeccionar la broca de taladro Mantenimiento E InspecciónInspección de los tornillos Mantenimiento de motorMantenimiento y reparación Cambio de grasaPage Page Page Page Page Page Hitachi Koki Canada Co