Hitachi DH 30PB, DH 30PC Assembly and Operation, Applications, Prior to Operation

Page 10

English

ASSEMBLY AND OPERATION

APPLICATIONS

Rotation and striking function

◯Drilling anchor holes

◯Drilling holes in concrete

◯Drilling holes in tile

Rotation only function

◯Drilling in steel or wood (with optional accessories).

◯Tightening machine screws, wood screws (with optional accessories). Striking only function

◯Light-duty chiselling of concrete, groove digging and edging.

PRIOR TO OPERATION

1.Power source

Ensure that the power source to be utilized conforms to the power source requirements specified on the product nameplate.

2.Power switch

Ensure that the switch is in the OFF position. If the plug is connected to a receptacle while the switch is in the ON position, the power tool will start operating immediately and can cause serious injury.

3.Extension cord

When the work area is far away from the power source, use an extension cord of sufficient thickness and rated capacity. The extension cord should be kept as short as practicable.

WARNING:

Damaged cord must be replaced or repaired.

4.Check the receptacle

If the receptacle only loosely accepts the plug, the receptacle must be repaired. Contact a licensed electrician to make appropriate repairs.

If such a fautly receptacle is used, it may cause overheating, resulting in a serious hazard.

10

Image 10

Contents Avertissement AdvertenciaContents Important Safety Information Meanings of Signal WordsSafety General Safety RulesEnglish Specific Safety Rules and Symbols Never operate without all guards in placeBlades and accessories must be securely mounted to the tool Make Them Available to Other Users Owners of this Tool Double Insulation for Safer OperationFunctional Description SpecificationsName of Parts Applications Assembly and OperationPrior to Operation Confirming condition of the environment Installation of dust cup or dustCollector B Optional accessories Mounting the drill bit FigSelecting the function mode HOW to USESelecting the driver bit Rotation + Striking Switch operationRotation only When driving machine screws Fig When driving wood screws FigUsing the stopper Fig Striking only DH30PCHOW to USE the Core BIT for Light Load Using the side handleHow to bore Fig Dismounting. FigInspecting the drill bits Maintenance and InspectionMaintenance of the motor Inspecting the screwsHow to replase grease Service and repairsPage Page Page Page Page Page Informations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTRegles Generale DE Securite SecuriteConserver CES Instructions Français Regles DE Securite Specifiques ET Symboles NE Jamais toucher les parties mobilesUtiliser l’outil correct Ne pas essuyer les parties en plastique avec du solvant Double Isolation Pour UN Fonctionnement Plus SUR Description Fonctionnelle NOM DES PartiesInterrupteur d’alimentation Avant L’UTILISATIONSource d’alimentation Cordon prolongateurVérification des conditions d’environnement Montage du foret de perçage FigSélection du mode de fonction Sélection de la mèche pour visseuseFonctionnement de l’interrupteur UtilisationRotation + frappe Rotation seulement Lors du vissage des vis machine Fig Enfoncement de vis à bois FigPercussion uniquement DH30PC Utilisation de l’arràtoir FigUtilisation de la poignée latérale MontagePerçage Fig Démontage FigEntretien du moteur Contrôle du foret de perçageInspection des vis Contrôle des balais en carbone FigComment remplacer la graisse Entretien et reparationFrançais Page Page Page Page Page Información Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónNormas Generales DE Seguridad SeguridadGuarde Estas Instrucciones Español Normas Y Símbolos Específicos DE Seguridad No toque Nunca las piezas móviles Maneje con cuidado las herramientas eléctricas Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Nomenclatura Descripción FuncionalEspecificaciones Aplicaciones Montaje Y OperaciónAntes DE LA Operación Confirme las condiciones del medio ambiente Montaje de la broca FigSelección de la broca destornillador Como SE USASelección del modo de función Rotación + golpeteo Operación del conmutadorRotación solamente Español Percusión solamente DH30PC Atornillando tornillos para madera FigModo de usar el tope Fig Modo DE Usar LA Barrena Tubularpara Cargas Ligeras Uso del asa lateralMontaje Modo de taladrar FigDesmontaje Fig Inspección de los tornillos Mantenimiento E InspecciónInspeccionar la broca de taladro Mantenimiento de motorCambio de grasa Mantenimiento y reparaciónPage Page Page Page Page Page Hitachi Koki Canada Co