DeWalt DWE4010 DWE4010T manual Safety Warnings Specific for Grinding Operations, Residual Risks

Page 8

ENGLISH

over kickback or torque reaction during start up. The operator can control torque reaction or kickback forces, if proper precautions are taken.

b)Never place your hand near the rotating accessory. Accessory may kickback over your hand.

c)Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in direction opposite to the wheel’s movement at the point of snagging.

d)Use special care when working corners, sharp edges etc. Avoid bouncing and snagging the accessory. Corners, sharp edges or bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback.

e)Do not attach a saw chain woodcarving blade or toothed saw blade. Such blades create frequent kickback and loss of control.

Safety Warnings Specific for Grinding Operations

a)Use only wheel types that are recommended for your power tool and the specific guard designed for the selected wheel. Wheels for which the power tool was not designed cannot be adequately guarded and are unsafe.

b)The guard must be securely attached to the power tool and positioned for maximum safety, so the least amount of wheel is exposed towards the operator. The guard helps to protect the operator from broken wheel fragments, accidental contact with wheel and sparks that could ignite clothing.

c)Wheels must be used only for recommended applications. For example: do not grind with the side of cut-off wheel. Abrasive cut-off wheels are intended for peripheral grinding, side forces applied to these wheels may cause them to shatter.

d)Always use undamaged wheel flanges that are of correct size and shape for your selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut-off wheels may be different from grinding wheel flanges.

e)Do not use worn down wheels from larger power tools. Wheel intended for larger power tool is not suitable for the higher speed of a smaller tool and may burst.

Residual Risks

In spite of the application of the relevant safety regulations and the implementation of safety devices, certain residual risks cannot be avoided. These are:

Impairment of hearing.

Risk of personal injury due to flying particles.

Risk of burns due to accessories becoming hot during operation.

Risk of personal injury due to prolonged use.

Risk of dust from hazardous substances.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual before use.

Wear ear protection.

Wear eye protection.

DATE CODE POSITION (FIG. 1)

The date code (e), which also includes the year of manufacture, is printed into the housing.

Example:

2013 XX XX

Year of Manufacture

Package Contents

The package contains:

1Angle grinder

1Guard

1Side handle

1Flange set

1Two pin spanner

1Instruction manual

1Exploded drawing

Check for damage to the tool, parts or accessories which may have occurred during transport.

Take the time to thoroughly read and understand this manual prior to operation.

6

Image 8
Contents DWE4010 DWE4010T ﺍﻝﻉﺭﺏﻱﺓ ﻡﺕﺭﺝﻡ ﻉﻥ ﺍﻝﺕﻉﻝﻱﻡﺍﺕ ﺍﻝﺃﺹﻝﻱﺓ DWE4010 DWE4010Tc ﻞﻜﺷ Technical Data Definitions Safety GuidelinesCongratulations Denotes risk of electric shock Denotes risk of fireUse of an RCD reduces the risk of electric shock Additional Specific Safety RulesSafety Instructions for All Operations Causes and Operator Prevention of Kickback Safety Warnings Specific for Grinding Operations Package ContentsResidual Risks Markings on ToolAssembly and Adjustments Operation Maintenance Protecting the Environment Félicitations Caractéristiques techniquesDéfinitions consignes de sécurité Dommages corporels gravesSécurité Individuelle Utilisation ET Entretien DES Outils ÉlectriquesRéparation Règles Particulières DE Sécurité AdditionnellesConsignes générales de sécurité Causes et prévention anti-rebonds Consignes spécifiques de sécurité propres au meulageRisques résiduels Étiquettes sur l’appareilContenu de l’emballage Sécurité électriqueInstallation de la poignée latérale fig Utilisation d’une rallongeMontage ET Réglages Mounting and Removing the Guard figPosition correcte des mains fig Avant tout utilisationFonctionnement Consignes d’utilisationBouton de blocage de l’arbre fig Applications métalUtilisation de disques à lamelles Balais autorupteursAccessoires en option Protection de l’environnementﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ ﺕﺍﻭﺩﻸﻟ ﺔﻣﺎﻌﻟﺍ ﻥﺎﻣﻷﺍ ﺕﺍﺮﻳﺬﺤﺗ ﺔﻴﻨﻔﻟﺍ ﺕﺎﻧﺎﻴﺒﻟﺍﻥﺎﻣﻷﺍ ﺕﺎﻤﻴﻠﻌﺗ ﺕﺎﻔﻳﺮﻌﺘﻟﺍ ﺔﻴﻓﺎﺿﻹﺍ ﺓﺩﺪﺤﻤﻟﺍ ﻥﺎﻣﻷﺍ ﺪﻋﺍﻮﻗ ﺦﻠﺠﻟﺍ ﺕﺎﻴﻠﻤﻌﺑ ﺔﺻﺎﺨﻟﺍ ﺔﻣﻼﺴﻟﺍ ﺕﺍﺮﻳﺬﺤﺗ ﺔﻴﻘﺒﺘﻤﻟﺍ ﺮﻃﺎﺨﻤﻟﺍﺓﺍﺩﻷﺍ ﻰﻠﻋ ﺕﺎﻣﻼﻌﻟﺍ ﺎﻬﻤﻄﺤﺗ ﻲﻓ تﺎﻧاﻮﻄﺳﻷاﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ ﺔﻣﻼﺴﻟﺍ ﻂﺳﻭﻷﺍ ﻕﺮﺸﻟﺍ ﻲﺴﻴﺋﺮﻟﺍ ﺭﺎﻴﺘﻟﺍ ﺲﺑﺎﻗ ﻝﺍﺪﺒﺘﺳﺍ ﺎﻴﻘﻳﺮﻓﺇﻭﺔﻟﺎﻄﺘﺳﻻﺍ ﻞﺑﺎﻛ ﻡﺍﺪﺨﺘﺳﺍ ﻂﺒﻀﻟﺍﻭ ﻊﻴﻤﺠﺘﻟﺍ ﺕﺎﻴﻠﻤﻋ6ﻭ ،1 ﻥﻼﻜﺸﻟﺍ ﺢﻴﺤﺼﻟﺍ ﺪﻴﻟﺍ ﻊﺿﻮﻣ ﺦﻠﺠﻟﺍ ﺹﺮﻗ ﺔﻟﺍﺯﺇﻭ ﺐﻴﻛﺮﺗ5ﻭ ،4ﻭ ،1 ﻝﺎﻜﺷﻷﺍ ﺢﻴﺗﺎﻔﻤﻟﺍﻒﻴﻈﻨﺘﻟﺍ ﺔﻳﺭﺎﻴﺘﺧﻻﺍ ﺕﺎﻘﺤﻠﻤﻟﺍﺔﺌﻴﺒﻟﺍ ﺔﻳﺎﻤﺣ ﺔﻴﻧﺪﻌﻤﻟﺍ ﺕﺎﻘﻴﺒﻄﺘﻟﺍPage Page Page Iraq N365700 11/13