Bosch Power Tools 1821 manual Assembly, Wheel Guard Installation, Vibration Control Side Handle

Page 10

BM 1609929Y07 10-10:BM 1609929Y07 10-10 1/18/11 10:06 AM Page 10

Functional Description and Specifications (Continued)

Model number

1821, 1821D

Max. type 1 and 27 grinding wheels

5" Dia.

* Max. type 1A and 27A cutting wheel

5" Dia.

* Max. flap disc

5" Dia.

Accessory speed rating must be equal to or greater than the tool’s speed rating. Do not

exceed the recommended wheel diameter.

NOTE: Not recommended for use with type 11 cup wheels.

* NOTE: For tool specifications refer to the nameplate on your tool.

Assembly

WHEEL GUARD INSTALLATION

!WARNING Wheel guard must be attached when using disc

grinding or cutting wheels. Always keep wheel guard between you and your work while grinding or cutting.

The position of the guard can be adjusted to accommodate the operation being performed.

To attach wheel guard DISCONNECT tool from power source.

Position wheel guard on spindle neck so that the arrow on guard lines up with the arrow on the spindle neck. Rotate wheel guard clockwise 90º until it clicks in place (Fig. 2).

TO ADJUST GUARD: depress guard release button (Fig. 1), rotate guard to desired position, release button and let it click in place.

TO REMOVE GUARD: Depress release button, rotate guard until arrow on guard lines up with arrow on spindle neck, and remove guard from spindle neck.

FIG. 2

WHEEL SPINDLE

GUARD NECK

LOCK NUT AND BACKING FLANGE

Your tool is equipped with a threaded spindle for mounting accessories. Always use the supplied lock nut (and backing flange) that has same thread size as spindle.

VIBRATION CONTROL SIDE HANDLE

The side handle is used to control and balance the tool. The handle must be threaded into the front housing on either side of the tool, depending on personal preference and comfort. Use the side handle for safe control and ease of operation (Fig. 1).

OPTIONAL HAND GUARD

The hand guard is to be used with backing pads, sanding discs and wire brushes to keep fingers and hand away from work surface, sharp edges, burrs and debris. When using the optional hand guard accessory insert side handle through hole in guard and then thread into housing (Fig. 1).

Ensure that hand guard is positioned between hand and backing pad, sanding disc or wire brush.

-10-

Image 10
Contents See Ver la páginaWork area safety Keep work area clean and well lit General Power Tool Safety WarningsSave ALL Warnings Instructions for Future Reference Power Tool-Specific Safety Warnings BM 1609929Y07 10-10BM 1609929Y07 10-10 1/18/11 1005 AM Safety Warnings Specific for Wire Brushing Operations Additional Safety Warnings Symbols Name Designation/ExplanationBM 1609929Y07 10-10BM 1609929Y07 10-10 1/18/11 1006 AM Angle Grinders Functional Description and SpecificationsPaddle Switch Grinding Wheel GuardWheel Spindle Guard Neck Lock NUT and Backing Flange AssemblyWheel Guard Installation Vibration Control Side HandleType Grinding Wheel Spindle Wheel Guard Backing Flange Disc Grinding Wheel AssemblyAbrasive Type 1A & 27A Wheel Assembly Lock NUTSanding Disc Lock NUT Wire Brush Wire Brush Assembly Sanding Accessories Assembly Backing PADTo Install Backing PAD Sanding Disc Wire Wheel AssemblySpindle DRY Diamond Wheel TRI-CONTROL Paddle SwitchOperating Instructions DRY Diamond WheelGrinding Tips Grinding OperationsDisc Grinding Wheels Cutting MetalSanding Tips Sanding OperationsSelecting Sanding Disc Sanding WoodWire Brush Operations MaintenanceCertain cleaning agents ! Caution and solvents damage AccessoriesExtension Cords Sécurité personnelle Sécurité du lieu de travailSécurité électrique Utilisation et entretien des outils électroportatifsEntretien Avertissements sur les rebonds et effets associés La meule Avertissements supplémentaires concernant la sécurité Utilisez un protège-main pendant le ponçage et le brossageSymboles Symbole Nom Désignation/ExplicationSymboles suite Description fonctionnelle et spécifications Rectifieuses d’anglesPose DU Protecteur DE Meule Description fonctionnelle et spécifications suiteAssemblage Poignée Latérale AntivibrationsMeule DE Type Bride Dappui Écrou DE Ensemble DE Meule a DisqueArbre BlocageEnsemble DE Brosse Métallique Ensemble Daccessoires DE Poncage Disque D’APPUIBrosse Métallique Arbre Disque ’APPUI Disque DE Poncage Ensemble DE Brosse Métallique À TouretBride Dappui Consignes de fonctionnementArbre Meule Diamantée Pour Travail À SEC Meule Diamantéearbre Pour Travail SEC Bride DappuiTravaux de meulage Ponçage DU Bois Travaux de ponçageChoix DES Disques DE Ponçage Ponçage DES MétauxTravaux à la brosse métallique EntretienAccessoires Cordons de rallongeSeguridad eléctrica Seguridad del área de trabajoSeguridad personal Servicio de ajustes y reparaciones Uso y cuidado de las herramientas mecánicasRetroceso y advertencias relacionadas BM 1609929Y07 10-10BM 1609929Y07 10-10 1/18/11 1006 AM Advertencias de seguridad adicionales Símbolos Símbolo Nombre Designación/explicaciónSímbolos continuación Descripción funcional y especificaciones Amoladoras angularesProtector Cuello DE LA DEL Muela Husillo EnsamblajeProtector DE LA Mano Opcional Tuerca DE Fijación Rueda DE Husillo Rueda DE Amolar DE TipoRuedas Abrasivas DE Tipo 1 Para Amoladoras Rectas Husillo Zapata DE Soporte Disco DE Lijar Tuerca DE Fijación Zapata DE SoportePara Instalar LA Zapata DE Soporte Y EL Disco DE Lijar Ensamblaje DEL Cepillo DE AlambreModelos 1821 solamente Instrucciones de funcionamientoInterruptor DE Paleta Tricontrol Modelos 1821D solamenteConsejos Para Amolar Operación de amoladoRuedas DE Amolar DE Disco Corte DE MetalConsejos Para Lijar Operaciones de lijadoSeleccion DEL Disco DE Lijar Lijado DE MaderaMantenimiento Cordones de extensión AccesoriosRemarques Notas Remarques Notas 1609929Y07