Bosch Power Tools 1821 manual Sanding Accessories Assembly Backing PAD, Wire Wheel Assembly

Page 12

BM 1609929Y07 10-10:BM 1609929Y07 10-10 1/18/11 10:06 AM Page 12

SANDING ACCESSORIES ASSEMBLY
SANDING ACCESSORIES ASSEMBLY		FIG. 5
BACKING PAD
	Before attaching a backing
! WARNING	Before attaching a backing
! WARNING	pad be sure its maximum
	pad be sure its maximum
safe operating speed is not exceeded by the
nameplate speed of the tool.
	Wheel guard may not be
! WARNING	Wheel guard may not be
! WARNING	used for most sanding
	used for most sanding
operations. Always reinstall wheel guard
when converting back to grinding operations.
TO INSTALL BACKING PAD AND
SANDING DISC
Disconnect tool from power source.
Attach hand guard (Fig. 1). Set the tool on its
top side (spindle up). Place the rubber
backing pad onto the spindle shaft. Center
the sanding disc on top of the backing pad.
Insert the lock nut through the disc and
thread onto the spindle as far as you can with
thread onto the spindle as far as you can with
your fingers. Press in the spindle lock, then
your fingers. Press in the spindle lock, then
tighten the backing pad securely with lock nut
wrench (Fig. 5).
TO REMOVE: Reverse procedure.

SPINDLE

BACKING

PAD

SANDING

DISC

LOCK NUT

WIRE

BRUSH

WIRE BRUSH ASSEMBLY

Before assembling wire brush to this tool, disconnect from the power source. Attach hand guard (Fig. 1). Wire brushes are equipped with their own threaded hub, simply thread on to spindle. Be sure to seat against shoulder before turning tool “ON”.

TO REMOVE: Reverse procedure.

WIRE WHEEL ASSEMBLY

Before assembling wire wheel to this tool, disconnect from the power source. Attach type 27 guard (Fig. 2). Wire wheeels are equipped with their own threaded hub, simply thread on to spindle. Be sure to seat against shoulder before turning tool “ON”.

TO REMOVE: Reverse procedure.

MASONRY CUTTING WHEEL ASSEMBLY Disconnect plug from power source. Completely unscrew the four screws and rotate the tool head carefully to the new position without removing it from the housing. For paddle switch tools, switch should face “down” towards work surface. For slide switch tools, slide should face “up” towards user, so the tool can be used for long masonry cutting applications. Screw in and tighten the four screws again. (Fig. 6)

!WARNING Return tool head to original position when returning to

grinding, sanding, brushing or metal cutting applications.

FIG. 6

-12-

Image 12

Contents See Ver la páginaGeneral Power Tool Safety Warnings Work area safety Keep work area clean and well litSave ALL Warnings Instructions for Future Reference Power Tool-Specific Safety Warnings BM 1609929Y07 10-10BM 1609929Y07 10-10 1/18/11 1005 AM Safety Warnings Specific for Wire Brushing Operations Additional Safety Warnings Symbols Name Designation/ExplanationBM 1609929Y07 10-10BM 1609929Y07 10-10 1/18/11 1006 AM Functional Description and Specifications Paddle Switch Grinding WheelAngle Grinders GuardAssembly Wheel Guard InstallationWheel Spindle Guard Neck Lock NUT and Backing Flange Vibration Control Side HandleDisc Grinding Wheel Assembly Abrasive Type 1A & 27A Wheel AssemblyType Grinding Wheel Spindle Wheel Guard Backing Flange Lock NUTSanding Accessories Assembly Backing PAD To Install Backing PAD Sanding DiscSanding Disc Lock NUT Wire Brush Wire Brush Assembly Wire Wheel AssemblyTRI-CONTROL Paddle Switch Operating InstructionsSpindle DRY Diamond Wheel DRY Diamond WheelGrinding Operations Disc Grinding WheelsGrinding Tips Cutting MetalSanding Operations Selecting Sanding DiscSanding Tips Sanding WoodWire Brush Operations MaintenanceAccessories Certain cleaning agents ! Caution and solvents damageExtension Cords Sécurité du lieu de travail Sécurité électriqueSécurité personnelle Utilisation et entretien des outils électroportatifsEntretien Avertissements sur les rebonds et effets associés La meule Avertissements supplémentaires concernant la sécurité Utilisez un protège-main pendant le ponçage et le brossageSymboles Symbole Nom Désignation/ExplicationSymboles suite Description fonctionnelle et spécifications Rectifieuses d’anglesDescription fonctionnelle et spécifications suite AssemblagePose DU Protecteur DE Meule Poignée Latérale AntivibrationsEnsemble DE Meule a Disque ArbreMeule DE Type Bride Dappui Écrou DE BlocageEnsemble Daccessoires DE Poncage Disque D’APPUI Brosse Métallique Arbre Disque ’APPUI Disque DE PoncageEnsemble DE Brosse Métallique Ensemble DE Brosse Métallique À TouretConsignes de fonctionnement Arbre Meule Diamantée Pour Travail À SECBride Dappui Meule Diamantéearbre Pour Travail SEC Bride DappuiTravaux de meulage Travaux de ponçage Choix DES Disques DE PonçagePonçage DU Bois Ponçage DES MétauxTravaux à la brosse métallique EntretienAccessoires Cordons de rallongeSeguridad del área de trabajo Seguridad eléctricaSeguridad personal Servicio de ajustes y reparaciones Uso y cuidado de las herramientas mecánicasRetroceso y advertencias relacionadas BM 1609929Y07 10-10BM 1609929Y07 10-10 1/18/11 1006 AM Advertencias de seguridad adicionales Símbolos Símbolo Nombre Designación/explicaciónSímbolos continuación Descripción funcional y especificaciones Amoladoras angularesEnsamblaje Protector Cuello DE LA DEL Muela HusilloProtector DE LA Mano Opcional Husillo Rueda DE Amolar DE Tipo Tuerca DE Fijación Rueda DERuedas Abrasivas DE Tipo 1 Para Amoladoras Rectas Zapata DE Soporte Para Instalar LA Zapata DE Soporte Y EL Disco DE LijarHusillo Zapata DE Soporte Disco DE Lijar Tuerca DE Fijación Ensamblaje DEL Cepillo DE AlambreInstrucciones de funcionamiento Interruptor DE Paleta TricontrolModelos 1821 solamente Modelos 1821D solamenteOperación de amolado Ruedas DE Amolar DE DiscoConsejos Para Amolar Corte DE MetalOperaciones de lijado Seleccion DEL Disco DE LijarConsejos Para Lijar Lijado DE MaderaMantenimiento Cordones de extensión AccesoriosRemarques Notas Remarques Notas 1609929Y07