Bosch Power Tools RA1181, RA118EVSTB manual Installing a WET/DRY VAC, Router and Switch Operation

Page 23

Router Table Operation

BEFORE PROCEEDING ANY FURTHER, MAKE SURE THE SWITCH ON THE ROUTER IS IN THE OFF POSITION AND THE SWITCH LEVER IS IN THE OFF POSITION.

The switch power cord can now be plugged into the extension cord.

MAKE SURE THAT POWER CORDS FROM THE ROUTER, ACCESSORIES, THE SWITCH CASE, AND THE EXTENSION CORD DO NOT AND CANNOT COME IN CONTACT WITH THE ROUTER OR ANY MOVING PARTS OF THE ROUTER.

ROUTER AND SWITCH OPERATION

This section explains operation of the switch with the power cord plugged into the extension cord.

The router will turn ON when the toggle switch is toggled to the ON (RESET) position.

1.Position the ON/OFF switch on the router in the ON position. On certain routers this will require the use of the switch trigger and “LOCK-ON” button. (Consult router owner’s manual.) Make sure the switch on the switch case is in the OFF position when doing this.

2.To turn the router ON, lift the switch cover and toggle the switch to the ON position. See A on page 22.

3.To turn the router OFF, push on the switch cover. See B on page 22.

NEVER LEAVE THE ROUTER UNATTENDED WHILE IT IS RUNNING OR BEFORE IT COMES TO A COMPLETE STOP.

NOTE: In the event of an overload, the internal switch circuit breaker will trip the switch to the OFF position. This will interrupt power to the router and any accessory plugged into the switch itself. If this occurs, proceed as follows:

1.Unplug the switch cord from the extension cord.

2.Remove the workpiece from the router table.

3.Correct the cause of the overload situation (i.e. the load exceeds the rated capacity of the switch).

4.Plug the switch power cord into the extension cord.

5.Restart the router as described in the section

ROUTER AND SWITCH OPERATION.

WHEN THE ROUTER TABLE IS NOT IN USE

1.Press the switch cover to turn the switch OFF.

2.Remove the lockout key.

3.Store the lockout key in a safe location where it is not available to children and other unauthorized persons.

4.Unplug the switch cord from the extension cord.

5.Remove the router bit from the router.

6.Position the router collet assembly below the top of the router table.

NOTE: If the key should become lost or damaged, replacement keys are available from your local Bosch dealer.

INSTALLING A WET/DRY VAC

INSTALLATION OF A WET/DRY VAC TO THE DUST COLLECTOR

The guard/dust collector assembly has a port for connecting a wet/dry vac hose with a 21⁄2″ nozzle. To attach, simply push the nozzle into the port while holding the fence assembly in place.

Operating the router table without a wet/dry vac can result in an excessive buildup of sawdust and wood chips under the fence assembly and overhead guard, reducing the performance of the router table and fence assembly.

RECOMMENDATION: To maximize performance, regardless of whether a wet/dry vac is being used, remove the sawdust and wood chips from under the fence assembly and overhead guard as needed.

RECOMMENDATION: It is always a good practice to keep the work area clean. As necessary, remove any accumulated sawdust and wood chips from the top of the router table, as well as from the surrounding work area and floor.

DO NOT REACH INTO THE AREA OF THE BIT WHILE THE ROUTER IS PLUGGED IN!

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents See Read Before UsingFor English ¿Habla español?Power Tool Safety Rules Table of ContentsService Additional Safety Warnings for Router TablesFence traps are dangerous for two reasons Improper Fence Location and Workpiece FeedImportant Information About Extension Cords This tool complies to NOM SymbolsDescription Quantity Parts ListFence Assembly Starter Pin AssemblyParts List Fasteners for Table Assembly Countersunk Phillips 31 1/4-20 x 1 1⁄ 2 ″ Carriage Bolt Tools Required not included Router Table AssemblyAssembling the Router Table Table LEG Inserts FIGAttach the SWITCH/FASCIA Assembly to the Router Table FIG Attach the Switch to the Fascia FIGAssembling the Fence Figs Assembling the FenceFigs a -7C Installing the Router Mounting PlatePreliminary Installation of the Router Mounting Plate Tools RequiredMounting Plate Guide for Compatible Routers Fig Determine the Mounting Method to be Used see chart onRouter Hole Fasteners Mount Brand Model Pattern Required Attach Router to Mounting Plate FigsOVER-TABLE Height Adjustment Final Installation of the Router Mounting Plate FigAttaching the Fence to the Table Installing the FenceMethod 1 Fig RA1190 Router Table Floor Stand featuresMounting the Router Table to a Work Surface or Workbench Method 2 Fig Tabletop Inserts Fig To Install Tabletop Inserts FigGeneral Information Switch InstructionsRouter Table Operation Electrical RequirementsTo operate the switch Connecting the Router Power Cord to the SwitchSwitch Operation Installation of a WET/DRY VAC to the Dust Collector Installing a WET/DRY VACRouter and Switch Operation When the Router Table is not in USETabletop Featherboard Fig Installing the Router BIT CutterAssembling the Featherboards Figs Fence Featherboard FigsAdjusting the Fence Facing Fig Routing Using Featherboards FigAdjusting Depth and Height of CUT Fig Remove the board from the table and lower Full Edge Cutting or Jointing FigsRouter Bits Figs Edge Cutting with NonpilotedEdge Cutting with Piloted Router Bits Figs Before proceeding GROOVING, FLUTING, and VeiningFigs Using a Miter Gauge not supplied Using the Starter PIN for Edge Forming of CurvesImportants Table des MatiéresConsignes DE Sécurité Assemblage de la table à toupieRéparation Consignes de sécurité supplèmentaires pour la table à toupiePlacées incorrectement quand on observe ce qui suit Emplacement du guide et sens d’avance incorrectsInformation importante pour les cordons de rallonge Le guide et/ou la pièce sontSymbole Nom Désignation/Explication SymbolesRep Description Quantité Liste de piècesListe de pièces Attaches Fournis Pour le montage des toupies No Rep Description QuantitéAttaches Fournis Pour l’assemblage de la table Attaches Fournis Pour l’assemblage du guideVis à métaux Phillips à Assemblage DE LA Table À Toupie Assemblage de la table à toupieFixez L’INTERRUPTEUR AU Tableau DE Bord FIG Assemblage DU Guide Figs et Assembler LE GuideUtils Requis NON Compris Installer LA Plaque DE Montage DE LA ToupieGuide DE Plaque DE Montage Pour Toupies Compatibles Fig LE Fonctionnement Choix DU Schéma DE Trous DE LA ToupieMontage Fixation DE LA Toupie À LA Plaque DE Montage Figs etAjustement DE Hauteur SUR LA Table Fixation DE LA Plaque DE Montage DELA Toupie Fig Fixez LE Guide À LA Table Fig Installation DU GuideCaractéristiques du support de table à toupie Bosch RA1190 Méthode 1 FIGMéthode 2 FIG Bagues DU Dessus DE LA Table FIG Installez LES Bagues DU Dessus DE LA Table FIGSécurité Électrique Mode D’EMPLOI DE L’INTERRUPTEURFonctionnement de la table à toupie Renseignements Généraux Pour faire fonctionner l’interrupteur Fonctionnement DE L’INTERRUPTEURProcédez comme suit Fonctionnement DE LA Toupie ET DE L’INTERRUPTEURInstallation DE LA Fraise Installer UN Aspirateur AVALE-TOUTGuide biseauté de la table Fig Assemblage DES Guides Biseautés FigsGuide biseauté du guide Figs et Réglage DU Parement DU Guide FIG Toupillage À L’AIDE DES Guides Biseautés FigRéglage DE LA Profondeur ET DE LA Hauteur DE LA Coupe Fig Coupe EN Bord OU Assemblage Figs et Toupie NON-PILOTÉE Figs et Coupe EN Bord Avec DES Fraises DELe garde n’est pas illustré pour Plus de clarté RAINURAGE, Gougeage ET Nervurage Figs et Utilisation D’UN Guide D’ONGLET non fourni Instrucciones Importantes DE Seguridad ContenidoNormas de seguridad para herramientas mecánicas Servicio Utilización y cuidado de las herramientasFigura a Símbolo Nombre Designación/explicación SímbolosClave No Descripción Cantidad Informaciónes importantes sobre los cables de extensionLista de piezas Superficie La mesaEnsamblado de la guía Tabla de biselado Sujetadores Para montar las fresadoras Sujetadores Para el ensamblado de la mesa de fresadoSujetadores Para el ensamblado de la guía Tornillo de máquina Phillips embutido Herramientas Necesarias Montaje de la mesa de fresadoMontaje DE LA Mesa DE Fresado Insertos DE LAS Patas DE LA Mesa FIGUNA EL Interruptor a LA Fascia FIG Cómo Armar LA Guía Figs y Cómo Armar LA GuíaHerramientas Necesarias no incluidas Cómo Instalar LA Placa DE Montaje DE LA FresadoraMguía DE LA Placa DE Montaje Para Fresadoras Compatibles FIG Cómo Elegir EL Patrón DE Orificios DE LA FresadoraMontaje UNA LA Fresadora a LA Placa DE Montaje Figs yAjuste DE Altura DE Sobremesa Instalación Final DE LA Placa DE Montaje DE LA Fresadora FIGCómo Sujetar LA Guía a LA Mesa Instalación DE LA GuíaMétodo 1 FIG Método Alterno FIG Instalación DE LAS Encastres DE LA Superficie DE LA Mesa FIG Encastres DE LA Superficie DE LA Mesa FIGInstrucciones Para EL Interruptor Requisitos Eléctricos Operación de la mesa de fresadoInformación General Para operar el interruptor Operación DEL InterruptorSi esto ocurre, siga estos pasos Operación DE LA Fresadora Y DEL InterruptorCómo Instalar LA Broca DE LA Fresadora Cortador Cómo Instalar UNA Aspiradora SECA/HÚMEDATabla de biselado para la superficie de la mesa Fig Cómo Armar LA LAS Tablas DE Biselado FigsTabla de biselado de la guía Figs y Cómo Ajustar EL Refrentado DE LA Guía FIG Cómo Fresar Utilizando Tablas DE Biselado FIGLa línea B indica la profundidad de corte deseada Cómo Ajustar LA Profundidad Y LA Altura DEL Corte FIGCorte O Unión DEL Borde Completo Figs y La protección de seguridad no aparece Instale la broca piloteada que desee en la fresadora Corte DE LOS Bordes CON Brocas DE Fresado Piloteadas Figs yRANURAS, Acanaladuras Y Vetas Figs y En cualquier dirección y se vuelve a ajustar la perilla Cómo Utilizar UN Calibrador DE Inglete no Incluido610 927 748 09/05
Top Page Image Contents