Bosch Power Tools RA118EVSTB Router Table Operation, Switch Instructions, Electrical Requirements

Page 21

Router Table Operation

SWITCH INSTRUCTIONS

ELECTRICAL REQUIREMENTS

A 14 gauge (or heavier) three-wire extension cord with a three-hole grounding receptacle and three-hole grounding plug is to be used for connecting the switch to an electrical outlet.

DAMAGED OR WORN EXTENSION CORDS ARE NOT TO BE USED AND ARE TO BE REPLACED IMMEDIATELY.

The electrical cord at the back of the switch will accept three-hole extension cords.

The electrical receptacles at the back of the switch will accept either three-prong or two-prong plugs from a router or accessory.

In the event of a malfunction or breakdown, grounding provides the path of least resistance for electrical current in order to reduce the risk of electrical shock. This switch box is equipped with an electrical cord that has an equipment-grounding connector and a grounding plug.

The extension cord must be plugged into a matching outlet that has been installed by a licensed electrician and grounded in accordance with

all local codes and ordinances.

DO NOT modify the plug from the switch if it does not plug into the extension cord. Obtain an extension cord with the proper outlet.

Improper connection of the equipment-grounding conductor can result in risk of an electrical shock. The conductor with insulation that has a green outer surface, with or without yellow stripes, is the equipment- grounding conductor.

DO NOT CONNECT THE EQUIPMENT-GROUNDING CONDUCTOR TO A LIVE TERMINAL.

GENERAL INFORMATION

The power switch is designed for use with most BOSCH Router Tables. It provides the convenience of an ON (RESET)-OFF switch at the front of the table, thus eliminating the need to reach underneath the table to turn the router ON and OFF.

The power switch also provides an optional simultaneous ON-OFF control of an additional accessory, such as a light or wet/dry vac. The switch has an internal, resettable circuit breaker to provide overload protection.

Check with a licensed electrician if the grounding instructions are not completely understood, or if there is doubt as to whether the electrical outlet or extension cord is properly grounded.

DO NOT PERMIT FINGERS TO TOUCH TERMINALS OF THE PLUG WHEN PLUGGING IT INTO OR REMOVING IT FROM THE OUTLET.

IF NOT PROPERLY GROUNDED, A POWER TOOL CAN PRESENT POTENTIAL HAZARDS OF ELECTRICAL SHOCK, WHICH CAN POSSIBLY RESULT IN SERIOUS BODILY INJURY OR DEATH, particularly when used in a damp location, in proximity to plumbing or out-of-doors. If an electrical shock occurs, there is always the potential of a secondary hazard, such as your hands contacting the router bit, or falling down or against an object.

USE THE SWITCH BOX ONLY WHEN PROPERLY ASSEMBLED TO THE ROUTER TABLE. USE ONLY WITH A ROUTER THAT HAS ALSO BEEN PROPERLY INSTALLED ON A PROPERLY ASSEMBLED ROUTER TABLE.

THE SWITCH HAS A RATING OF 15 AMPS. DO NOT EXCEED A TOTAL COMBINED RATING OF 15 AMPS WHEN CONNECTING THE ROUTER AND ANY ACCESSORIES SUCH AS A LIGHT OR WET/DRY VACUUM.

FIG. 17

LOCKOUT

KEY SWITCH BOX

Switch receptacle orientation (as viewed from front of switch)

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents For English Read Before Using¿Habla español? SeePower Tool Safety Rules Table of ContentsService Additional Safety Warnings for Router TablesImproper Fence Location and Workpiece Feed Important Information About Extension CordsFence traps are dangerous for two reasons This tool complies to NOM SymbolsFence Assembly Parts ListStarter Pin Assembly Description QuantityParts List Fasteners for Table Assembly Countersunk Phillips 31 1/4-20 x 1 1⁄ 2 ″ Carriage Bolt Assembling the Router Table Router Table AssemblyTable LEG Inserts FIG Tools Required not includedAttach the SWITCH/FASCIA Assembly to the Router Table FIG Attach the Switch to the Fascia FIGAssembling the Fence Figs Assembling the FencePreliminary Installation of the Router Mounting Plate Installing the Router Mounting PlateTools Required Figs a -7CMounting Plate Guide for Compatible Routers Fig Determine the Mounting Method to be Used see chart onRouter Hole Fasteners Mount Brand Model Pattern Required Attach Router to Mounting Plate FigsOVER-TABLE Height Adjustment Final Installation of the Router Mounting Plate FigAttaching the Fence to the Table Installing the FenceRA1190 Router Table Floor Stand features Mounting the Router Table to a Work Surface or WorkbenchMethod 1 Fig Method 2 Fig Tabletop Inserts Fig To Install Tabletop Inserts FigRouter Table Operation Switch InstructionsElectrical Requirements General InformationConnecting the Router Power Cord to the Switch Switch OperationTo operate the switch Router and Switch Operation Installing a WET/DRY VACWhen the Router Table is not in USE Installation of a WET/DRY VAC to the Dust CollectorAssembling the Featherboards Figs Installing the Router BIT CutterFence Featherboard Figs Tabletop Featherboard FigAdjusting the Fence Facing Fig Routing Using Featherboards FigAdjusting Depth and Height of CUT Fig Remove the board from the table and lower Full Edge Cutting or Jointing FigsRouter Bits Figs Edge Cutting with NonpilotedEdge Cutting with Piloted Router Bits Figs GROOVING, FLUTING, and Veining FigsBefore proceeding Using a Miter Gauge not supplied Using the Starter PIN for Edge Forming of CurvesConsignes DE Sécurité Table des MatiéresAssemblage de la table à toupie ImportantsRéparation Consignes de sécurité supplèmentaires pour la table à toupieInformation importante pour les cordons de rallonge Emplacement du guide et sens d’avance incorrectsLe guide et/ou la pièce sont Placées incorrectement quand on observe ce qui suitSymbole Nom Désignation/Explication SymbolesRep Description Quantité Liste de piècesListe de pièces Attaches Fournis Pour l’assemblage de la table No Rep Description QuantitéAttaches Fournis Pour l’assemblage du guide Attaches Fournis Pour le montage des toupiesVis à métaux Phillips à Assemblage DE LA Table À Toupie Assemblage de la table à toupieFixez L’INTERRUPTEUR AU Tableau DE Bord FIG Assemblage DU Guide Figs et Assembler LE GuideUtils Requis NON Compris Installer LA Plaque DE Montage DE LA ToupieGuide DE Plaque DE Montage Pour Toupies Compatibles Fig LE Fonctionnement Choix DU Schéma DE Trous DE LA ToupieMontage Fixation DE LA Toupie À LA Plaque DE Montage Figs etFixation DE LA Plaque DE Montage DE LA Toupie FigAjustement DE Hauteur SUR LA Table Fixez LE Guide À LA Table Fig Installation DU GuideCaractéristiques du support de table à toupie Bosch RA1190 Méthode 1 FIGMéthode 2 FIG Bagues DU Dessus DE LA Table FIG Installez LES Bagues DU Dessus DE LA Table FIGMode D’EMPLOI DE L’INTERRUPTEUR Fonctionnement de la table à toupieSécurité Électrique Renseignements Généraux Pour faire fonctionner l’interrupteur Fonctionnement DE L’INTERRUPTEURProcédez comme suit Fonctionnement DE LA Toupie ET DE L’INTERRUPTEURInstallation DE LA Fraise Installer UN Aspirateur AVALE-TOUTAssemblage DES Guides Biseautés Figs Guide biseauté du guide Figs etGuide biseauté de la table Fig Réglage DU Parement DU Guide FIG Toupillage À L’AIDE DES Guides Biseautés FigRéglage DE LA Profondeur ET DE LA Hauteur DE LA Coupe Fig Coupe EN Bord OU Assemblage Figs et Toupie NON-PILOTÉE Figs et Coupe EN Bord Avec DES Fraises DELe garde n’est pas illustré pour Plus de clarté RAINURAGE, Gougeage ET Nervurage Figs et Utilisation D’UN Guide D’ONGLET non fourni Contenido Normas de seguridad para herramientas mecánicasInstrucciones Importantes DE Seguridad Servicio Utilización y cuidado de las herramientasFigura a Símbolo Nombre Designación/explicación SímbolosInformaciónes importantes sobre los cables de extension Lista de piezasClave No Descripción Cantidad La mesa Ensamblado de la guía Tabla de biseladoSuperficie Sujetadores Para el ensamblado de la mesa de fresado Sujetadores Para el ensamblado de la guíaSujetadores Para montar las fresadoras Tornillo de máquina Phillips embutido Montaje DE LA Mesa DE Fresado Montaje de la mesa de fresadoInsertos DE LAS Patas DE LA Mesa FIG Herramientas NecesariasUNA EL Interruptor a LA Fascia FIG Cómo Armar LA Guía Figs y Cómo Armar LA GuíaHerramientas Necesarias no incluidas Cómo Instalar LA Placa DE Montaje DE LA FresadoraMguía DE LA Placa DE Montaje Para Fresadoras Compatibles FIG Cómo Elegir EL Patrón DE Orificios DE LA FresadoraMontaje UNA LA Fresadora a LA Placa DE Montaje Figs yAjuste DE Altura DE Sobremesa Instalación Final DE LA Placa DE Montaje DE LA Fresadora FIGCómo Sujetar LA Guía a LA Mesa Instalación DE LA GuíaMétodo 1 FIG Método Alterno FIG Instalación DE LAS Encastres DE LA Superficie DE LA Mesa FIG Encastres DE LA Superficie DE LA Mesa FIGInstrucciones Para EL Interruptor Requisitos Eléctricos Operación de la mesa de fresadoInformación General Para operar el interruptor Operación DEL InterruptorSi esto ocurre, siga estos pasos Operación DE LA Fresadora Y DEL InterruptorCómo Instalar LA Broca DE LA Fresadora Cortador Cómo Instalar UNA Aspiradora SECA/HÚMEDACómo Armar LA LAS Tablas DE Biselado Figs Tabla de biselado de la guía Figs yTabla de biselado para la superficie de la mesa Fig Cómo Ajustar EL Refrentado DE LA Guía FIG Cómo Fresar Utilizando Tablas DE Biselado FIGLa línea B indica la profundidad de corte deseada Cómo Ajustar LA Profundidad Y LA Altura DEL Corte FIGCorte O Unión DEL Borde Completo Figs y La protección de seguridad no aparece Instale la broca piloteada que desee en la fresadora Corte DE LOS Bordes CON Brocas DE Fresado Piloteadas Figs yRANURAS, Acanaladuras Y Vetas Figs y En cualquier dirección y se vuelve a ajustar la perilla Cómo Utilizar UN Calibrador DE Inglete no Incluido610 927 748 09/05
Top Page Image Contents