Bosch Power Tools RA1171 manual Attach the Router Mounting Plate Fig, OVER-TABLE Height Adjustment

Page 16

Router Table Assembly

ATTACH THE ROUTER MOUNTING PLATE (Fig. 13)

1.If the fence is already installed on the table, remove it before proceeding.

2.Place the router mounting plate (3) in the opening so the numbers on the scales are right side up, as seen from the front of the table. Using a straight edge, check to be certain that the surface of the router mounting plate is flush with the tabletop surface. NOTE: Failure to make sure the router mounting plate is flush with the tabletop surface can result in poor routing performance. Slide a square cut board from right to left across the router mounting plate to be sure that it moves smoothly.

3.To adjust the plate, insert the 6mm hex key through the outermost corner holes in the mounting plate and turn the leveling inserts clockwise to lower the mounting plate or counterclockwise to raise the mounting plate.

FIG. 13

33

3

4.Secure the router mounting plate (3) to the table with four #10-32 x 1/2″ pan-head machine screws

(33)(Fig. 13) through the outermost corner holes in the plate. Tighten the screws snugly, but do not overtighten.

TO REMOVE THE ROUTER AND/OR ROUTER MOUNTING PLATE

To remove the router from the mounting plate, you must first remove the router mounting plate from the router table.

THE FENCE MUST BE REMOVED FROM THE ROUTER TABLE WHEN REMOVING OR REINSTALLING THE ROUTER MOUNTING PLATE.

Make sure that the router is NOT plugged into a power outlet when installing into the table, removing from table, making adjustments or changing accessories. Router could accidentally start.

OVER-TABLE HEIGHT ADJUSTMENT

The router adapter plate features an access hole to allow use with the over-table height adjustment feature on the Bosch 1617 series routers. Refer to your router manual for additional information on using this feature.

For the Porter Cable 892 and 895 and the Milwaukee 5615 and 5616 model routers, it is necessary to drill an access hole to accommodate the over-table height adjustment:

1.Remove the subbase from the router and align the mounting holes in the subbase with the corresponding mounting holes in the adapter plate. Be sure to orient the subbase so that the router switch will be toward the front of the table.

1.Loosen the four #10-32 x 1/2″ pan-head Phillips machine screws (33) holding the router mounting plate to the tabletop.

2.Lift the router mounting plate and router upwards from the tabletop.

3.Remove the countersunk machine screws securing the router to the mounting plate.

4.When reinstalling the router mounting plate, be sure that the plate is level with the tabletop. If needed, readjust as described above.

2.Using a pencil or centerpunch, mark the location of the over-table height adjustment hole on the router adapter plate.

3.Remove the subbase from the adapter plate and carefully drill the over-table height adjustment hole.

4.Make sure that the hole will accommodate the height adjustment tool for your router. Remove any burrs or rough edges with sandpaper.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Read Before Using For English¿Habla español? SeeTable of Contents Power Tool Safety RulesAdditional Safety Warnings for Router Tables ServiceImproper Fence Location and Workpiece Feed Important Information About Extension CordsSymbols This tool complies to NOMParts List Fence AssemblyStarter Pin Assembly Description QuantitySwitch Assembly Fasteners for Table and Fence Assembly Allen-Head Connector Screw Router Table Assembly Assembling the Router TableTools Required Assemble Sides to Back FigAttaching the Switch to the Tabletop Fig Attach the Tabletop FigAssemble the Aluminum Miter Channel to the Tabletop FigAttach the Door Figs If the magnetic catch does not contactAssembling the Fence Assembling the Fence FigsDetermine the Mounting Method to be Used see chart on Mounting Plate Guide for Compatible Routers FigAttach Router to Mounting Plate Figs Router Hole Fasteners Mount Brand Model Pattern RequiredOVER-TABLE Height Adjustment Attach the Router Mounting Plate FigAttaching the Fence to the Table Fig Securing the Router Table to a Work Surface FigPreferred method Alternative methodTo Install Tabletop Inserts Fig Tabletop Inserts FigSwitch Instructions Router Table OperationElectrical Requirements All local codes and ordinancesGeneral Information Connecting the Router Power Cord to the SwitchCord Routing Switch Operation To operate the switchRouter and Switch Operation When the Router Table is not in USEAttaching and Using a WET/DRY Vacuum Using the Router TableInstalling the Router BIT Cutter Fence Featherboard Figs Assembling the Featherboards FigsTabletop Featherboard Fig Routing Using Featherboards Fig Adjusting the Fence Facing FigAdjusting Depth and Height of CUT Fig Full Edge Cutting or Jointing Figs Remove the board from the table and lowerEdge Cutting with Nonpiloted Router Bits Figs Edge Cutting with Piloted Router Bits Figs SecurelyFigs GROOVING, FLUTING, and VeiningBefore proceeding Using the Starter PIN for Edge Forming of Curves Using a Miter Gauge not suppliedConsignes DE Sécurité Table des MatiéresImportants Consignes de sécurité supplèmentaires pour la table à toupie RéparationEmplacement du guide et sens d’avance incorrects Information importante pour les cordons de rallongeSymboles Symbole Nom Désignation/ExplicationListe de pièces No Rep Description QuantitéEnsemble de la table Interrupteur Ensemble de goupille Bagues du dessusDescription Quantité No RepAttaches Fournis Pour l’assemblage de la table Attaches Fournis Pour le montage des toupiesVis de raccordement à tête Allen Assemblage de la table à toupie Assemblage DE LA Table À ToupieOutils Requis non inclus Fixez LES Côtés AU DOS FigFixez LE Dessus DE LA Table Fig Fixez L’INTERRUPTEUR SUR LE Dessus DE LA Table FigFixez LE Canal DU Guide D’ONGLET AU Dessus DE LA Table Fig Fixez LA Porte Figs et Assemblage DU Guide Assemblage DU Guide Figs etLE Fonctionnement Choix DU Schéma DE Trous DE LA Toupie Guide DE Plaque DE Montage Pour Toupies Compatibles FigFixation DE LA Toupie À LA Plaque DE Montage Figs et Installation DE LA Plaque DE Montage DE LA Toupie Fig Ajustement DE Hauteur SUR LA TableMéthode préférée Fixez LA Table DE LA Toupie SUR UNE Surface DE Travail FigAutre méthode Installez LES Bagues DU Dessus DE LA Table FIG Bagues DU Dessus DE LA Table FIGFonctionnement de la table à toupie Mode D’EMPLOI DE L’INTERRUPTEURSécurité Électrique Cheminement du cordon Renseignements GénérauxFonctionnement DE L’INTERRUPTEUR Pour faire fonctionner l’interrupteurFonctionnement DE LA Toupie ET DE L’INTERRUPTEUR ArrêtInstallation DE LA Fraise Cordement ET Utilisation DE ’ASPIRATEUR Eaux ET PoussièresGuide biseauté du guide Figs et Assemblage DES Guides Biseautés FigsGuide biseauté de la table Fig Toupillage À L’AIDE DES Guides Biseautés Fig Réglage DU Parement DU Guide FIGRéglage DE LA Profondeur ET DE LA Hauteur DE LA Coupe Fig Coupe EN Bord OU Assemblage Figs et Coupe EN Bord Avec DES Fraises DE Toupie NON-PILOTÉE Figs et Fonctionnement de la table à toupie RAINURAGE, Gougeage ET Nervurage Figs et Pour plus de clartéUtilisation D’UN Guide D’ONGLET non fourni Toujours en contact avec le palier pilote de la lameNormas de seguridad para herramientas mecánicas ContenidoInstrucciones Importantes DE Seguridad Utilización y cuidado de las herramientas ServicioPage Figura a Símbolos Símbolo Nombre Designación/explicaciónInformaciónes importantes sobre los cables de extension Lista de piezas Clave No Descripción CantidadComponentes Insertos de la Sujetadores Para el ensamblado de la mesa de fresado Tornillo conector de cabeza Allen Montaje de la mesa de fresado Montaje DE LA Mesa DE FresadoCómo Ensamblar LOS Lados a LA Parte Trasera FigInstalación DEL Interruptor Fig Cómo Sujetar LA Superficie DE LA Mesa FigCómo Sujetar LA Puerta Figs y Montaje DE LA Guía Cómo Armar LA Guía Figuras 8 yCómo Elegir EL Patrón DE Orificios DE LA Fresadora Mguía DE LA Placa DE Montaje Para Fresadoras Compatibles FIGUNA LA Fresadora a LA Placa DE Montaje Figs y UNA LA Placa DE Montaje DE LA Fresadora FIG Ajuste DE Altura DE SobremesaMétodo preferido Cómo Sujetar LA Guía a LA Mesa FigMétodo alternativo Encastres DE LA Superficie DE LA Mesa Fig Instalación DE LAS Encastres DE LA Superficie DE LA Mesa FIGOperación de la mesa de fresado Instrucciones Para EL Interruptor Requisitos EléctricosInformación General Ubicación del cableOperación DEL Interruptor Para operar el interruptorOperación DE LA Fresadora Y DEL Interruptor Si esto ocurre, siga estos pasosCómo Unir Y Usar UNA Aspiradora DE SECADO/MOJADO Cómo Instalar LA Broca DE LA Fresadora CortadorTabla de biselado de la guía Figuras 18 y Cómo Armar LA LAS Tablas DE Biselado FigurasTabla de biselado sobre la mesa Fig Cómo Fresar Utilizando Tablas DE Biselado FIG Cómo Ajustar EL Refrentado DE LA Guía FIGCómo Ajustar LA Profundidad Y LA Altura DEL Corte Fig Corte O Unión DEL Borde Completo Figs y FirmementeRefrentado DE LA Guía Broca DE LA Fresadora Altura Corte DE LOS Bordes CON Brocas DE Fresado Piloteadas Figs y RANURAS, Acanaladuras Y Vetas Figs y Cómo Utilizar UN Calibrador DE Inglete no Incluido Broca Piloteado Calibrador DE IngletePage Page 610 930 993 09/05
Top Page Image Contents