Harbor Freight Tools 94748 manual INSPECTION, MAINTENANCE, and Cleaning, Troubleshooting

Page 12

INSPECTION, MAINTENANCE, AND CLEANING

1.WARNING! Make sure the Power Switch (27) of the Belt Sander is in its “OFF” position and the tool is unplugged from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. (See Figure E.)

2.Before each use: Inspect the general condition of the Belt Sander. Check for loose screws, misalignment or binding of moving parts, damaged electrical wiring, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use.

Do not use damaged equipment.

3.Before each use: Inspect the Sanding Belt (66). Using dull Sanding Belts will cause excessive wear on the motor of the Belt Sander and will not produce satisfactory sanding results. Replace with a new Sanding Belt when needed.

(See Figure E.)

4.To clean the exterior parts of the Belt Sander: Use only a clean cloth and mild detergent. Then dry. Do not immerse any electrical part of the tool in any liq- uids.

5.CAUTION! All maintenance, service, or repairs not mentioned in this manual must only be performed by a qualified service technician.

TROUBLESHOOTING

Problem

 

Possible Solution

Belt Sander will not turn on.

1.

Make sure to firmly squeeze the Power Switch.

 

2.

Make sure the Power Cord/Plug is connected to a

 

 

working, 120 volt, grounded, electrical outlet.

 

3.

Discontinue using the Belt Sander, and have a quali-

 

 

fied service technician check out the tool.

Belt Sanding not removing material adequately

1.

Do not apply excessive downward pressure on the

from the workpiece.

 

Belt Sander.

 

2.

Increase the speed of the Belt Sander.

 

3.

Make sure the Sanding Belt is not dull or clogged with

 

 

excessive debris.

 

4.

Use a coarser grit Sanding Belt.

Gashes and hollows occur in the workpiece

Avoid tilting or rocking the Belt Sander or sanding in one

when sanding.

spot too long.

Sanding Belt slips off rollers of tool while in use.

Adjust the tracking of the Sanding Belt.

Power Switch will not turn the Belt Sander off.

Unplug the Belt Sander from its electrical outlet. Discon-

 

tinue using the Belt Sander, and have a qualified service

 

technician check out the tool.

SKU 94748

For technical questions, please call 1-800-444-3353

PAGE 12

Image 12
Contents For technical questions or replacement parts, please call Belt SanderProduct Specifications General Safety RulesSave this Manual Work AreaElectrical Safety Personal SafetyService Tool USE and CareSpecific Safety Rules Industrial applications must follow Osha guidelinesGrounding Grounded Tools Tools With Three Prong PlugsDouble Insulated Tools Tools With Two Prong Plugs Extension CordsSee Figure C, next See Figure CSymbology Nameplate Extension Cord LengthFeet 120 or 240 VoltProduct Features UnpackingSee Figure E To install the Sanding Belt See Figure E To remove the Sanding BeltSee Figure E SKU For technical questions, please call Operating Instructions INSPECTION, MAINTENANCE, and Cleaning TroubleshootingDo not use damaged equipment Parts List Please Read the Following CarefullyAssembly Diagram For technicalLimited 90 DAY Warranty Ponceuse DE Ceinture Spécifications DE Produit Règles Répandues DE SécuritéSauvez CE Manuel Région DE TravailSécurité Électrique Sécurité Personnalisée Utilisation D’INSTRUMENT ET SoinRègles DE Sécurité Spécifiques EntretienModèle Installer À LA Terre Sauvez CES InstructionsCordons d’Extension Voir l’Image aImage a Image B Plaque Longueur DE Cordon D’EXTENSION 30 m 45 mDéfaisant Caractéristiques DE ProduitVoir l’Image E Installer la Ceinture pour le fait d’éroder Enlever la Ceinture pour le fait d’éroderLE Fait DE Faire Marcher DES Instructions ’INSPECTION, LA Maintenance ET LE Nettoyage Problème Solution Possible LE Fait DE Fixer DES ProblèmesListe DE Pièces Pièce Description QuantitéDiagramme De Montage Déférez au texte Anglais pour ’explication de Garantie Garantie