Hitachi W 6VB2 Mounting and Dismounting the HEX-SOCKET or the BIT, Tightening Self-drilling screw

Page 13

English

4.Tightening Self-drilling screw

When the supplied magnet bit holder is used to tighten the Self-drilling screw into a steel plate, cut material stuck in the magnet bit will degrade the work efficiency.

To prevent this, the non-magnetic bit holder (optional accessory) is recom- mended. The stainless locator with bushing (optional accessory) will prevent the bushing from being worn.

MOUNTING AND DISMOUNTING THE HEX-SOCKET OR THE BIT

CAUTION

Be sure to switch power OFF and disconnect the plug from receptacle to avoid serious trouble.

1.Dismounting the hex-socket (Fig. 7)

(1) While rotating the Sub-Stopper pull it out from the locator.

(2) Remove the hex-socket, hold it with the opposite side of bit with hand or vise and pull out the bit with pliers.

2.Dismounting the bit (Fig. 8)

Remove the sub-stopper (A) alike case of hex-head socket and remove the bit holder, then pull out the bit with pliers.

Sub-Stopper (B)

Magnetic hex. socket

Fig. 7

3.Dismounting the bit (Fig. 9)

Remove the sub-stopper (C) alike case of hex-head socket and remove the bit holder, then pull out the bit with pliers.

4.Mounting the hex-socket or the bit

Install the bit in the reverse order to removel.

Sub-Stopper (A)

Bit Bit holder (Short type)

Fig. 8

Sub-Stopper (C)

Bit Bit holder

Fig. 9

13

Image 13
Contents 6VB2 W 8VB Contents Important Information Meanings of Signal WordsGeneral Safety Rules SafetyEnglish Keep all screws, bolts and covers tightly in place Do not wipe plastic parts with solvent Specific Safety Rules and SymbolsDouble Insulation for Safer Operation Functional Description SpecificationsName of Parts Applications Assembly and OperationPrior to Operation Confirm the direction of bit rotation Fig Adjusting the tightening depth FigSwitch operation and rotational speed adjustment HOW to USE the Screw DriverMounting the bit Screw driver operationTightening Self-drilling screw Mounting and Dismounting the HEX-SOCKET or the BITDismounting the hex-socket Fig Dismounting the bit FigMaintenance and Inspection Standard Accessories AccessoriesFor hex-head screws For other screwsPlastic case Code No Hook Code No Signification DES Mots D’AVERTISSEMENT Informations ImportantesRegles Generale DE Securite SecuriteConserver CES Instructions Français Utiliser l’outil correct Garder propres les évents d’air du moteur Regles DE Securite Specifiques ET Symboles Double Isolation Pour UN Fonctionnement Plus SUR NOM DES Parties Description FonctionnelleAvant L’UTILISATION Réglage de la profondeur de serrage Fig Vérifier la direction de la tête de vissagePour vis autoperceuses à tête ronde Fig Comment Utiliser LA VisseuseFonctionnement de la visseuse Sens de rotation du manchon six pansDémontage du manchon six pans Fig Serrage d’une vis auto-foreuseEntretien ET Inspection Accessoires Standard AccessoiresPour vis à tête six pans Pour les autres visBoîtier en plastique No. de code Crechet No. de code Significado DE LAS Palabras DE Señalización Información ImportanteNormas Generales DE Seguridad SeguridadGuarde Estas Instrucciones Español Utilice la herramienta correcta Maneje con cuidado las herramientas eléctricas Normas Y Símbolos Específicos DE Seguridad Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura ¡GUARDE Este Manual DE Instrucciones DondeNomenclatura Descripción FuncionalEspecificaciones Aplicaciones Montaje Y OperaciónAntes DE LA Operación Ajustar la profundidad de apretado Fig Confirmar la dirección de rotación de la broca FigFuncionamiento del destornillador Como Usar EL DestornilladorDirección de giro del portatornillos Inserción de tornillos autotaladradores Desmontaje de la broca Desmontaje del portatornillo hexagonalCuando montre el portatornillo hexagonal o la broca Mantenimiento E Inspección Accesorios Estándar AccesoriosPara tornillos cabeza hexagonal Para otros tornillosCaja de plástico Num. de código Gancho Num. de código Page Page Page Page 812