Hitachi CR 18DMR instruction manual Remove the battery from the battery charger

Page 19

English

5.Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out the battery from the battery charger.

CAUTION:

Repair is required if the receptacle is not secured properly or the power cord does not stay in the receptacle. Consult your electrician. Using the charger in this condition may lead to fire.

If the charge status lamp is blinking orange rapidly (in 0.2 second intervals) and the buzzer sounds intermittently for 5 seconds, check that the hole for connecting the battery is not obstructed. Remove any obstructions. If no obstructions are found, the battery or charger may be malfunctioned. Return both to your place of purchase.

If the charge time lamp does not light when the power cord is connected to the receptacle, disconnect the power cord, and check that the battery is attached correctly.

The battery retains heat when used or left for prolonged periods in direct sunlight. In this state, the charge time lamp flashes red, and the battery cannot be charged immediately. Leave the battery inserted in the charger, and charging will commence when the battery cools down.

If the lamp goes out while charging, disconnect the power cord, and leave for 3 to 5 minutes before reconnecting. If the problem persists, call for repairs.

Leave 5 minutes between charging batteries as the charger may overheat leading to malfunction.

The battery life is finished if it can only be used for short periods even when fully charged. Purchase a new battery. Continuing to use a depleted battery may cause the charger to malfunction.

NOTE:

Charging times may be longer depending on the surrounding temperature and battery conditions.

Charge time lamp indications are only a guide, and may vary depending on the surrounding temperature and battery conditions.

Remove the battery from the charger when not in use.

Revitalizing the battery (trickle recharge).

A new battery or a battery that has not been used for extensive periods may not charge completely due to internal chemicals being inert.

Leave the battery inserted in the charger for 8 to 12 hours after charging is complete. The charger automatically “revitalizes” the battery by trickle recharging.

How to make the batteries perform longer.

(1)Recharge the batteries before they become completely exhausted.

When you feel that the power of the tool becomes weaker, stop using the tool and recharge its battery. If you continue to use the tool and exhaust the electric current, the battery may be damaged and its life will become shorter.

(2)Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after use. If such a battery is recharged immediately after use, its internal chemical substance will deteriorate, and the battery life will be shortened. Leave the battery and recharge it after it has cooled for a while.

19

Image 19
Contents Avertissement Cordless Reciprocating SawContents Meanings of Signal Words Important Safety InformationGeneral Safety Rules for ALL Battery Operated Tools SafetyEnglish Specific Safety Rules and Symbols Do not wipe plastic parts with solvent Read ALL Instructions Important Safety Instructions for Battery ChargerEnglish Make Them Available to Other Users Owners of this Tool Cordless Reciprocating Saw CR18DMR Functional DescriptionModel Name of Parts〈UC24YJ 〉 Battery Charger 〈UC24YFA〉〈UC18YG〉 Battery Charger SpecificationsCharging Method Assembly and OperationRemoval and Installation Method of Battery Applications〈UC24YFA〉 Remove the battery from the battery charger Disconnect battery charger from the receptacleRegarding electric discharge in case of new batteries, etc Charging Insert the plug of battery charger into the receptacleInsert the battery to the battery charger How to make the batteries perform longerBattery overheated. Unable to charge Revitalizing the battery trickle recharge Center Prior to Operation Before USEMounting the blade Maintenance and Inspection of SAW Blade Mount When the Blade is BrokenDismounting the blade Adjusting the base HOW to USE the Cordless Reciprocating SAWConfirm that the battery is mounted correctly Cutting metallic materials Switch operationSawing curved lines Cutting lumberPlunge cutting English Maintenance and Inspection Check for Dust Disposal of the exhausted batteryService and repairs Service parts listModifications Standard Accessories AccessoriesSold separately Battery EB1830HL Saw BladesSignification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéConserver CES Instructions SecuriteAvertissement Lire et coxmprendre toutes les instructions Avertissement Regles DE Securite Specifiques ET Symboles Ne pas essuyer les parties en plastique avec du solvant Manipuler l’outil motorisé avec précautionLire Tout CE Mode Demploi Français Français Scie alternative à batterie CR18DMR Description FonctionnelleModele NOM DES Parties〈UC24YJ〉 Chargeur de batterie 〈UC24YFA〉Chargeur de batterie Méthode DE Recharge Méthode DE Retrait ET D’INSTALLATION DE LA BatterieInsérer la batterie dans le chargeur de batterie Brancher la fiche du chargeur de batterie dans la priseRecharge Débrancher le chargeur de batterie de la prise PrecautionRetirer la batterie du chargeur de batterie Comment prolonger la durée de vie des batteries Français Revitalisation de la batterie recharge d’entretient Brancher la fiche du chargeur de batterie dans la prise Avant L’OPERATON Avant L’UTILISATIONMontage de la lame Démontage de la lame Entretien ET Inspection DE LA Monture DE Lame SI LA Lame EST CasseeRéglage du socle Comment Utiliser LA Scie Alternative À Batterie’assurer que la batterie est montée Correctement.Socle  Appuyer le socle fermement contre la pièce Fonctionnement de l’interrupteurCoupe de métaux Coupe de boisAttaque en plein bois Sciage de lignes courbesEntretien ET Inspection Entretien et réparation Vérifier s’il y a de la poussièreMise au rebut d’une batterie usée RangementListe des pièces de rechange Accessoires Standard AccessoiresBatterie EB1830HL Lames Accessoires SUR OPTION......vendus séparémentSignificado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadGuarde Estas Instrucciones SeguridadAdvertencia Lea y entienda todas las instrucciones Advertencia Utilice la herramienta correcta Normas Y Símbolos Específicos DE SeguridadManeje correctamente la herramienta No limpie las partes de plástico con disolvente Maneje con cuidado las herramientas eléctricasLEA Todas LAS Instrucciones Español Español Sierra reciprocante a batería CR18DMR Descripción FunctionalModelo Nomenclatura〈UC18YG 〉 Cargador de baterías 〈UC24YFA〉Especificaciones Método DE Carga Montaje Y OperaciónAplicaciones Método DE Extracción E Instalación DE LA BateríaCarga Inserte la batería en el cargador de bateríasDescarga eléctrica en caso de baterías nuevas, etc Desconecte el cargador de baterías del tomacorrienteExtraiga la batería del cargador de baterías PrecauciónForma de hacer que las baterías duren más Minutos Rojo Finalizar Carga Desconecte el cargador de baterías del tomacorriente Revitalización de la batería recarga hábil Antes DE LA Utilización Montaje de la hoja Antes DE LA OperaciónDesmontaje de la hoja Cuando SE Rompa LA Hoja Carrera Como Usar LA Sierra Sable a BateríaCómo ajustar la base Cerciórese de que la batería esté correctamente instaladaCorte de materiales metálicos Operación del interruptor Presione la base firmemente contra la pieza de trabajo Corte de líneas curvadas Corte de maderaCorte por penetración Español Mantenimiento E Inspección Mantenimiento y reparación Comprobación del polvoEliminación de las baterías agotadas AlmacenamientoModificaciones Lista de repuestosAccesorios Estándar AccesoriosBatería EB1830HL Hojas Accesorios OPCIONALES......De venta por separadoPage Page Blade Holder a Page Page Hitachi Koki Canada Co