Black & Decker BDCS1806 Operating Instructions General Cuts, Shoe Adjustment for 90 Cuts

Page 13

90537965 BD Circ Saws 5/30/08 10:11 AM Page 13

SHOE ADJUSTMENT FOR 90° CUTS

IF ADDITIONAL ADJUSTMENT IS NEEDED:

•Adjust the saw to 0° bevel.

•Retract blade guard (11). Place the saw on blade side.

•Loosen bevel adjustment knob (13). Place a square against the blade (10) and shoe (8) to adjust the 90° setting.

•Loosen jam nut and move the adjustment screw (13a) so that the shoe will stop at the proper angle and retighten jam nut.

•Confirm the accuracy of the setting by checking the squareness of an actual cut on a scrap piece of material.

OPERATING INSTRUCTIONS

WARNING: To reduce the risk of serious personal injury, read, understand and follow all important safety warnings and instructions prior to using tool.

GENERAL CUTS

GUARD AGAINST KICKBACK

With battery removed, follow all assembly, adjustment and set up instructions.

Make sure lower guard operates. Select the proper blade for the material to be cut.

•Measure and mark work for cutting.

•Support and secure work properly (See Safety Rules and Instructions).

•Use appropriate and required safety equipment (See Safety Rules).

•Secure and maintain work area (See Safety Rules).

•With battery inserted, make sure switch turns saw on and off.

WARNING: To reduce the risk of injury, It is important to support the work properly and to hold the saw firmly to prevent loss of control which could cause personal injury. Fig. G illustrates typical hand support.

ATTACHING AND REMOVING THE BLADE - FIGURE L, L1

NOTE: The first time the blade bolt is removed from saw without a blade installed, it may be necessary to place the blade wrench on the bolt head and tap it sharply in the counter clockwise direction.

•Retract lower guard (11) and assemble blade (10) and clamp washer (21) as shown in figure L.

•(BDCS2406 only) To prevent blade rotation keep the spindle lock button (28) depressed and rotate the blade until the spindle lock engages (figure L).

•Tighten the blade clamping screw securely with the blade wrench.

•(All other models) To prevent blade rotation while tightening the blade clamping screw (20), raise the lower guard and place the saw down on a piece of scrap wood as shown in Fig. L1. The blade teeth will dig into the scrap wood and prevent rotation of the blade.

•Tighten the blade clamping screw securely with the blade wrench.

NOTE: The blade wrench is stored in the saw housing as shown in figure M.

Lower Blade Guard

WARNING: Laceration Hazard. The lower blade guard is a safety feature which reduces the risk of serious personal injury. Never use the saw if the lower guard is missing, damaged, misassembled or not working properly. Do not rely on the lower blade guard to protect you under all circumstances. Your safety depends on following all warnings and precautions as well as proper operation of the saw. Check lower guard for proper closing before each use as outlined in Additional Safety Rules for Circular Saws. If the lower blade guard is missing or not working properly, have the saw serviced before using. To assure product safety and reliability, repair, maintenance and adjustment should be performed by an authorized service center or other qualified service organization, always using identical replacement parts.

WARNING: To minimize the risk of eye injury, always use eye protection. Carbide is a hard but brittle material. Foreign objects in the work piece such as wire or nails can cause tips to crack or break. Only operate saw when proper saw blade guard is in place. Mount blade securely in proper rotation before using, and always use a clean, sharp blade.

CAUTION: Do not cut ferrous metals (steel), masonry, glass or tile with this saw. A dull blade will cause slow, inefficient cutting overload on the saw motor, excessive splintering, and could increase the possibility of kickback.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Save this Manual for Future Reference BDCSL1806 BDGCS1806VEA EL Español EN LA Contraportada Personal Safety Electrical SafetyWork Area Tool Use and CareCauses and Operator Prevention of Kickback ServiceAdditional Safety Rules Circular Saws Guard Against Kickback Safety Instructions Lasers BDCSL1806 onlyTo Reduce the Risk of Kickback Per minute Safety Guidelines DefinitionsSafety Warnings and Instructions Charging Important Charging Notes Charging the BatteryBattery CAP Information FIG. C 11a Overview Figure D13a Bevel Angle Adjustment Figure K Cutting Depth Adjustment Figures I & JOperating Instructions General Cuts Shoe Adjustment for 90 CutsAttaching and Removing the Blade Figure L, L1 Installing the Batteries Figure N SwitchOperating the Laser BDCSL1806 only Automatic Electric BrakeSawing Operation Abrasive Type or Metal Cutting Blades on SAW AccessoriesFull TWO-YEAR Home USE Warranty Service InformationRbrc Seal Conserver CE Manuel Pour UN Usage Ultérieur Guide D’UTILISATIONSécurité Personnelle Conserver CES Mesures Zone DE TravailUtilisation ET Entretien DE L’OUTIL Mesures DE Sécurité Relatives À L’ÉLECTRICITÉEntretien Mesures DE Sécurité SpécifiquesCause de rebonds et mesures de prévention Mesures DE Sécurité Additionnelles Scies circulairesMesures Pour Minimiser LES Risques DE Rebonds Mesures de précaution contre les rebondsLa scie ce qui favorise la torsion de la lame BD Circ Saws 5/30/08 1011 AM La minute Lignes Directrices EN Matière DE Sécurité DéfinitionsCharge DE Batterie Avertissements de sécurité et directives chargementRemarques Importantes DE Chargement Avertissement S’assurer, au Information Concernant LE Capuchon DU BLOC-PILE FIG. CWron g 13a Réglage DE L’ANGLE DE Biseau Figure K Préparation pour l’assemblage et le réglageCoupes Générales FonctionnementRéglage DE LA Semelle Pour LES Coupes DE SE Protéger DES Effets DE RebondDétente Utilisation DU Laser BDCSL1806 SeulementFrein Électrique Automatique Mise EN MARCHE/ARRÊT DU Laser Laser IntégréRetirer LE BLOC-PILES DE LA Scie Avant DE Régler LE Laser Pour Utiliser LE Trait LaserOpérations DE Sciage AccessoiresDécoupe EN Poche Figure Q DE Matières Abrasives Avec LA ScieInformation SUR LES Réparations DépannageCaractéristiques Techniques DU Laser Conserve Este Manual Para Futuras Consultas Manual DE InstruccionesConserve Estas Instrucciones Reglas Generales DE SeguridadArea de trabajo Seguridad PersonalReglas DE Seguridad Especificas ServicioCausas DEL Contragolpe Y Prevención POR Parte DEL Operador Reglas DE Seguridad Adicionales Sierras CircularesLos que promueve que el disco cambie de dirección Protéjase contra el ContragolpePara Reducir EL Riesgo DE Contragolpe Instrucciones DE Seguridad Para EL Láser BDCSL1806 Solamente Minutos Corriente alterna Corriente directa Pautas DE SEGURIDAD/DEFINICIONESConstrucción clase Terminales de Conexión a tierre Revoluciones oUtilice un solo cargador cuando carga Instrucciones y advertencias de seguridad cargaCarga DE LA Batería Notas Importantes Sobre LA Carga Información Acerca DEL Protector DE LA Batería FIG. CMango principal Descripción DE LAS Funciones Figura D13a 2726 Cortes Generales Instrucciones DE OperaciónRegulación DEL Ángulo DE Bisel Figura K Ajuste DE LA Zapata Para Cortes DEInterruptor Colocación Y Remoción DE LA Hoja Figuras L Y L1Freno Eléctrico Automático Apague y encienda la sierra cuatro o cinco vecesLáser Incorporado EN LA Unidad USO DEL Láser BDCSL1806 SolamenteApagado Y Encendido DEL Láser Operación DE Corte Para Usar LA Línea LáserCortes Internos Figura Q Accesorios EL Sello Rbrc MEXICO, D.F CULIACAN, SINMERIDA, YUC MONTERREY, N.LBD Circ Saws 5/30/08 1011 AM

BDCS1807, BDGCS1806, BDCSL1806, BDCS1806, BDCS2406 specifications

Black & Decker has long been recognized for its high-quality tools, and the models 90537965, BDCS1806, BDCSL1806, BDCS2406, and BDGCS1806 exemplify the brand's commitment to innovation and user-friendly design. These cordless tools are ideal for both amateur handymen and seasoned professionals, delivering efficiency and convenience.

The Black & Decker 90537965 features a robust design, with a focus on power and durability. It offers a lithium-ion battery that ensures a longer runtime, making it perfect for extended tasks without the worry of running out of power. Its compact size allows for easy maneuverability in tight spaces, making it an essential tool for any toolbox.

The BDCS1806 is a versatile cordless screwdriver that makes light work of DIY projects. It is equipped with an ergonomic handle that enhances comfort during extended use. The forward and reverse switch allows for easy operation, while the built-in LED work light illuminates dark areas, ensuring precision even in low-light conditions. With a lightweight design, it reduces user fatigue while providing substantial power for various applications.

Next, the BDCSL1806 adds another layer of versatility with its variable speed settings. This feature allows users to adjust the speed for different tasks, ensuring optimal control whether driving screws or removing them. The battery charge indicator keeps the user informed of remaining power, minimizing downtime.

For those looking for a more powerful option, the BDCS2406 stands out with its heavy-duty capabilities. This model boasts increased torque, making it ideal for tougher materials. It also includes a quick-change chuck, enabling rapid bit changes without the need for additional tools, thereby enhancing productivity.

Finally, the BDGCS1806 is a game-changer with its innovative design. It integrates a compact and lightweight structure that does not compromise on performance. Like its counterparts, it features a lithium-ion battery that provides exceptional longevity and consistent power delivery.

In summary, Black & Decker's 90537965, BDCS1806, BDCSL1806, BDCS2406, and BDGCS1806 models combine cutting-edge technology with user-centric design. Their exceptional features, such as ergonomic handles, variable speed settings, and powerful lithium-ion batteries, make these tools indispensable for anyone seeking reliability and performance in their tool collection.
Top Page Image Contents