Black & Decker BDCS1806, 90537965, BDCS1807, BDCSL1806 Safety Warnings and Instructions Charging

Page 7

90537965 BD Circ Saws 5/30/08 10:11 AM Page 7

For your convenience and safety, the following labels are on your laser. (BDCSL1806)

SAFETY WARNINGS AND INSTRUCTIONS: CHARGING

1.This manual contains important safety and operating instructions.

2.Before using battery charger, read all instructions and cautionary warnings on battery charger and product using battery.

CAUTION: To reduce the risk of injury, use charger only with this product. Batteries in other products may burst causing personal injury or damage.

3.Do not expose charger to rain or snow.

4.Use of an attachment not recommended may result in a risk of fire, electric shock, or injury to persons.

5.To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger.

6.Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.

7.An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire, electric shock or electrocution.

a. Two-wire cords can be used with

2-wire or 3-wire extension cords. Only round jacketed extension cords should be used, and we recommend that they be listed by Underwriters Laboratories (U.L.). If the extension is to be used outside, the cord must be suitable for outdoor use. Any cord marked for outdoor use can also be used for indoor work. The letters "W" or "WA" on the cord jacket indicate that the cord is suitable for outdoor use.

b.An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety, and to prevent loss of power and overheating. The smaller the gauge number of the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity than 18 gauge. When using more than one extension to make up the total length, be sure each extension contains at least the minimum wire size for the total length.

8.Use only the specified charger when charging your tool. The use of any other charger could damage the tool or create a hazardous condition.

9.Use only one charger when charging.

10.Do not attempt to open the charger. There are no customer serviceable parts inside. Return to any authorized Black & Decker service center.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Save this Manual for Future Reference BDCSL1806 BDGCS1806VEA EL Español EN LA Contraportada Tool Use and Care Electrical SafetyPersonal Safety Work AreaCauses and Operator Prevention of Kickback ServiceAdditional Safety Rules Circular Saws Guard Against Kickback Safety Instructions Lasers BDCSL1806 onlyTo Reduce the Risk of Kickback Per minute Safety Guidelines DefinitionsSafety Warnings and Instructions Charging Important Charging Notes Charging the BatteryBattery CAP Information FIG. C 11a Overview Figure D13a Bevel Angle Adjustment Figure K Cutting Depth Adjustment Figures I & JOperating Instructions General Cuts Shoe Adjustment for 90 CutsAttaching and Removing the Blade Figure L, L1 Automatic Electric Brake SwitchInstalling the Batteries Figure N Operating the Laser BDCSL1806 onlySawing Operation Abrasive Type or Metal Cutting Blades on SAW AccessoriesFull TWO-YEAR Home USE Warranty Service InformationRbrc Seal Conserver CE Manuel Pour UN Usage Ultérieur Guide D’UTILISATIONMesures DE Sécurité Relatives À L’ÉLECTRICITÉ Conserver CES Mesures Zone DE TravailSécurité Personnelle Utilisation ET Entretien DE L’OUTILEntretien Mesures DE Sécurité SpécifiquesCause de rebonds et mesures de prévention Mesures DE Sécurité Additionnelles Scies circulairesMesures Pour Minimiser LES Risques DE Rebonds Mesures de précaution contre les rebondsLa scie ce qui favorise la torsion de la lame BD Circ Saws 5/30/08 1011 AM La minute Lignes Directrices EN Matière DE Sécurité DéfinitionsCharge DE Batterie Avertissements de sécurité et directives chargementRemarques Importantes DE Chargement Avertissement S’assurer, au Information Concernant LE Capuchon DU BLOC-PILE FIG. CWron g 13a Réglage DE L’ANGLE DE Biseau Figure K Préparation pour l’assemblage et le réglageSE Protéger DES Effets DE Rebond FonctionnementCoupes Générales Réglage DE LA Semelle Pour LES Coupes DEDétente Utilisation DU Laser BDCSL1806 SeulementFrein Électrique Automatique Pour Utiliser LE Trait Laser Laser IntégréMise EN MARCHE/ARRÊT DU Laser Retirer LE BLOC-PILES DE LA Scie Avant DE Régler LE LaserDE Matières Abrasives Avec LA Scie AccessoiresOpérations DE Sciage Découpe EN Poche Figure QInformation SUR LES Réparations DépannageCaractéristiques Techniques DU Laser Conserve Este Manual Para Futuras Consultas Manual DE InstruccionesSeguridad Personal Reglas Generales DE SeguridadConserve Estas Instrucciones Area de trabajoReglas DE Seguridad Especificas ServicioCausas DEL Contragolpe Y Prevención POR Parte DEL Operador Reglas DE Seguridad Adicionales Sierras CircularesLos que promueve que el disco cambie de dirección Protéjase contra el ContragolpePara Reducir EL Riesgo DE Contragolpe Instrucciones DE Seguridad Para EL Láser BDCSL1806 Solamente Revoluciones o Pautas DE SEGURIDAD/DEFINICIONESMinutos Corriente alterna Corriente directa Construcción clase Terminales de Conexión a tierreUtilice un solo cargador cuando carga Instrucciones y advertencias de seguridad cargaCarga DE LA Batería Notas Importantes Sobre LA Carga Información Acerca DEL Protector DE LA Batería FIG. CMango principal Descripción DE LAS Funciones Figura D13a 2726 Ajuste DE LA Zapata Para Cortes DE Instrucciones DE OperaciónCortes Generales Regulación DEL Ángulo DE Bisel Figura KApague y encienda la sierra cuatro o cinco veces Colocación Y Remoción DE LA Hoja Figuras L Y L1Interruptor Freno Eléctrico AutomáticoLáser Incorporado EN LA Unidad USO DEL Láser BDCSL1806 SolamenteApagado Y Encendido DEL Láser Operación DE Corte Para Usar LA Línea LáserCortes Internos Figura Q Accesorios EL Sello Rbrc MONTERREY, N.L CULIACAN, SINMEXICO, D.F MERIDA, YUCBD Circ Saws 5/30/08 1011 AM

BDCS1807, BDGCS1806, BDCSL1806, BDCS1806, BDCS2406 specifications

Black & Decker has long been recognized for its high-quality tools, and the models 90537965, BDCS1806, BDCSL1806, BDCS2406, and BDGCS1806 exemplify the brand's commitment to innovation and user-friendly design. These cordless tools are ideal for both amateur handymen and seasoned professionals, delivering efficiency and convenience.

The Black & Decker 90537965 features a robust design, with a focus on power and durability. It offers a lithium-ion battery that ensures a longer runtime, making it perfect for extended tasks without the worry of running out of power. Its compact size allows for easy maneuverability in tight spaces, making it an essential tool for any toolbox.

The BDCS1806 is a versatile cordless screwdriver that makes light work of DIY projects. It is equipped with an ergonomic handle that enhances comfort during extended use. The forward and reverse switch allows for easy operation, while the built-in LED work light illuminates dark areas, ensuring precision even in low-light conditions. With a lightweight design, it reduces user fatigue while providing substantial power for various applications.

Next, the BDCSL1806 adds another layer of versatility with its variable speed settings. This feature allows users to adjust the speed for different tasks, ensuring optimal control whether driving screws or removing them. The battery charge indicator keeps the user informed of remaining power, minimizing downtime.

For those looking for a more powerful option, the BDCS2406 stands out with its heavy-duty capabilities. This model boasts increased torque, making it ideal for tougher materials. It also includes a quick-change chuck, enabling rapid bit changes without the need for additional tools, thereby enhancing productivity.

Finally, the BDGCS1806 is a game-changer with its innovative design. It integrates a compact and lightweight structure that does not compromise on performance. Like its counterparts, it features a lithium-ion battery that provides exceptional longevity and consistent power delivery.

In summary, Black & Decker's 90537965, BDCS1806, BDCSL1806, BDCS2406, and BDGCS1806 models combine cutting-edge technology with user-centric design. Their exceptional features, such as ergonomic handles, variable speed settings, and powerful lithium-ion batteries, make these tools indispensable for anyone seeking reliability and performance in their tool collection.
Top Page Image Contents