Black & Decker BDCSL1806, 90537965, BDCS1806, BDCS1807, BDCS2406, BDGCS1806 Sawing Operation

Page 15

90537965 BD Circ Saws 5/30/08 10:11 AM Page 15

SWITCHING THE LASER ON AND OFF

•To turn the laser on, press the laser on/off button (3). To turn the laser off, press the button a second time.

NOTE: The laser on/off button occupies two different positions, the lower position is “on” (slightly depressed below flush) and the upper position is “off” (button is flush with the surface).

ADJUSTING THE LASER - FIGURE O&P

CAUTION: TURN OFF TOOL AND REMOVE BATTERY PACK FROM SAW BEFORE CHANGING ACCESSORIES OR MAKING ANY ADJUSTMENTS.

The laser can be adjusted to remove lateral and angular error.

•Using a securely mounted scrap piece of plywood or sheathing make a partial cut with this saw at least as long as the shoe.

•Turn the saw off, hold the saw motionless and after the blade stops rotating, remove the saw from the cut.

•Using a straight edge and pencil, draw a straight line on the plywood as if extending the cut from where it ended.

•REMOVE THE SAW BATTERY BEFORE MAKING LASER ADJUSTMENTS.

•With the saw set at maximum depth of cut, retract the lower guard and place the saw blade back in the cut to where it ended (at the start of the pencil line).

•With the saw shoe sitting solidly on the plywood, turn the laser on, loosen the laser adjustment screw (26) with the supplied wrench (12) and use the adjustment tabs (27) on each side of the laser module to align the laser line with the pencil line then retighten the adjustment screw.

•Turn the laser off and remove the saw from the cut before reinserting the saw battery.

TO USE THE LASER LINE

•Mark the line that you intend to cut on the workpiece.

•Adjust the depth and angle of cut as required.

•Push the laser on/off switch (3) to the “ON” position and project the laser beam.

•Push in on the lock-off button (2) and depress the saw on/off switch (1) and allow the blade to reach maximum speed.

•Place the saw shoe on the workpiece. Align the laser line with the mark on the workpiece and slowly push the saw forward keeping the laser line on the mark.

•Upon completion of the cut, release the trigger and allow the saw blade to come to a complete stop before switching off the laser.

SAWING OPERATION

WARNING: To reduce the risk of serious personal injury, always hold the tool with both hands.

•Let the blade run freely for a few seconds before starting the cut.

•Apply only a gentle pressure to the tool while performing the cut.

•Work with the shoe pressed against the workpiece.

POCKET CUTTING - FIGURE Q

CAUTION: Never move the saw backwards when pocket cutting. This may cause the unit to raise up off the work surface which could cause injury.

WARNING: Laceration Hazard. Never tie the blade guard in a raised position.

Pocket cutting is used to cut a hole in a piece of material without cutting from the side.

•Measure and mark work.

•Tilt saw forward and rest front of the shoe on material to be cut. Align so that cut will begin at the back of the drawn rectangle.

•Using the retracting lever, retract blade guard to an upward position, with the blade just clearing the material, start motor and gradually lower the saw into the material.

WARNING: Laceration Hazard. As blade starts cutting the material, release the retracting lever immediately.

•When the shoe rests flat on the material being cut, complete the cut in forward direction.

•Allow the blade to come to a complete stop before lifting saw from material.

•When starting each new cut, repeat the above steps.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents BDCSL1806 BDGCS1806 Save this Manual for Future ReferenceVEA EL Español EN LA Contraportada Tool Use and Care Electrical SafetyPersonal Safety Work AreaCauses and Operator Prevention of Kickback ServiceAdditional Safety Rules Circular Saws Safety Instructions Lasers BDCSL1806 only Guard Against KickbackTo Reduce the Risk of Kickback Per minute Safety Guidelines DefinitionsSafety Warnings and Instructions Charging Important Charging Notes Charging the BatteryBattery CAP Information FIG. C 11a Overview Figure D13a Bevel Angle Adjustment Figure K Cutting Depth Adjustment Figures I & JShoe Adjustment for 90 Cuts Operating Instructions General CutsAttaching and Removing the Blade Figure L, L1 Automatic Electric Brake SwitchInstalling the Batteries Figure N Operating the Laser BDCSL1806 onlySawing Operation Abrasive Type or Metal Cutting Blades on SAW AccessoriesService Information Full TWO-YEAR Home USE WarrantyRbrc Seal Conserver CE Manuel Pour UN Usage Ultérieur Guide D’UTILISATIONMesures DE Sécurité Relatives À L’ÉLECTRICITÉ Conserver CES Mesures Zone DE TravailSécurité Personnelle Utilisation ET Entretien DE L’OUTILEntretien Mesures DE Sécurité SpécifiquesCause de rebonds et mesures de prévention Mesures DE Sécurité Additionnelles Scies circulairesMesures de précaution contre les rebonds Mesures Pour Minimiser LES Risques DE RebondsLa scie ce qui favorise la torsion de la lame BD Circ Saws 5/30/08 1011 AM La minute Lignes Directrices EN Matière DE Sécurité DéfinitionsCharge DE Batterie Avertissements de sécurité et directives chargementRemarques Importantes DE Chargement Avertissement S’assurer, au Information Concernant LE Capuchon DU BLOC-PILE FIG. CWron g 13a Réglage DE L’ANGLE DE Biseau Figure K Préparation pour l’assemblage et le réglageSE Protéger DES Effets DE Rebond FonctionnementCoupes Générales Réglage DE LA Semelle Pour LES Coupes DEUtilisation DU Laser BDCSL1806 Seulement DétenteFrein Électrique Automatique Pour Utiliser LE Trait Laser Laser IntégréMise EN MARCHE/ARRÊT DU Laser Retirer LE BLOC-PILES DE LA Scie Avant DE Régler LE LaserDE Matières Abrasives Avec LA Scie AccessoiresOpérations DE Sciage Découpe EN Poche Figure QInformation SUR LES Réparations DépannageCaractéristiques Techniques DU Laser Conserve Este Manual Para Futuras Consultas Manual DE InstruccionesSeguridad Personal Reglas Generales DE SeguridadConserve Estas Instrucciones Area de trabajoReglas DE Seguridad Especificas ServicioCausas DEL Contragolpe Y Prevención POR Parte DEL Operador Reglas DE Seguridad Adicionales Sierras CircularesProtéjase contra el Contragolpe Los que promueve que el disco cambie de direcciónPara Reducir EL Riesgo DE Contragolpe Instrucciones DE Seguridad Para EL Láser BDCSL1806 Solamente Revoluciones o Pautas DE SEGURIDAD/DEFINICIONESMinutos Corriente alterna Corriente directa Construcción clase Terminales de Conexión a tierreInstrucciones y advertencias de seguridad carga Utilice un solo cargador cuando cargaCarga DE LA Batería Notas Importantes Sobre LA Carga Información Acerca DEL Protector DE LA Batería FIG. CMango principal Descripción DE LAS Funciones Figura D13a 2726 Ajuste DE LA Zapata Para Cortes DE Instrucciones DE OperaciónCortes Generales Regulación DEL Ángulo DE Bisel Figura KApague y encienda la sierra cuatro o cinco veces Colocación Y Remoción DE LA Hoja Figuras L Y L1Interruptor Freno Eléctrico AutomáticoUSO DEL Láser BDCSL1806 Solamente Láser Incorporado EN LA UnidadApagado Y Encendido DEL Láser Para Usar LA Línea Láser Operación DE CorteCortes Internos Figura Q Accesorios EL Sello Rbrc MONTERREY, N.L CULIACAN, SINMEXICO, D.F MERIDA, YUCBD Circ Saws 5/30/08 1011 AM

BDCS1807, BDGCS1806, BDCSL1806, BDCS1806, BDCS2406 specifications

Black & Decker has long been recognized for its high-quality tools, and the models 90537965, BDCS1806, BDCSL1806, BDCS2406, and BDGCS1806 exemplify the brand's commitment to innovation and user-friendly design. These cordless tools are ideal for both amateur handymen and seasoned professionals, delivering efficiency and convenience.

The Black & Decker 90537965 features a robust design, with a focus on power and durability. It offers a lithium-ion battery that ensures a longer runtime, making it perfect for extended tasks without the worry of running out of power. Its compact size allows for easy maneuverability in tight spaces, making it an essential tool for any toolbox.

The BDCS1806 is a versatile cordless screwdriver that makes light work of DIY projects. It is equipped with an ergonomic handle that enhances comfort during extended use. The forward and reverse switch allows for easy operation, while the built-in LED work light illuminates dark areas, ensuring precision even in low-light conditions. With a lightweight design, it reduces user fatigue while providing substantial power for various applications.

Next, the BDCSL1806 adds another layer of versatility with its variable speed settings. This feature allows users to adjust the speed for different tasks, ensuring optimal control whether driving screws or removing them. The battery charge indicator keeps the user informed of remaining power, minimizing downtime.

For those looking for a more powerful option, the BDCS2406 stands out with its heavy-duty capabilities. This model boasts increased torque, making it ideal for tougher materials. It also includes a quick-change chuck, enabling rapid bit changes without the need for additional tools, thereby enhancing productivity.

Finally, the BDGCS1806 is a game-changer with its innovative design. It integrates a compact and lightweight structure that does not compromise on performance. Like its counterparts, it features a lithium-ion battery that provides exceptional longevity and consistent power delivery.

In summary, Black & Decker's 90537965, BDCS1806, BDCSL1806, BDCS2406, and BDGCS1806 models combine cutting-edge technology with user-centric design. Their exceptional features, such as ergonomic handles, variable speed settings, and powerful lithium-ion batteries, make these tools indispensable for anyone seeking reliability and performance in their tool collection.
Top Page Image Contents