Black & Decker BDCS1807, 90537965, BDCS1806 Charging the Battery, Important Charging Notes

Page 8

90537965 BD Circ Saws 5/30/08 10:11 AM Page 8

11.DO NOT incinerate the tool or batteries even if they are severely damaged or completely worn out. The batteries can explode in a fire.

12.A small leakage of liquid from the battery cells may occur under extreme usage, charging or temperature conditions. This does not indicate a failure. However, if the outer seal is broken and this leakage gets on your skin:

a.Wash quickly with soap and water.

b.Neutralize with a mild acid such as lemon juice or vinegar.

c.If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10 minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a 25-35% solution of potassium hydroxide.

CHARGING THE BATTERY

THE BATTERIES IN YOUR POWER PACK ARE NOT FULLY CHARGED AT THE FACTORY. BEFORE ATTEMPTING TO CHARGE THEM, THOROUGHLY READ ALL OF THE SAFETY INSTRUCTIONS.

The charger is designed to use standard household 120 volt 60 Hz power. NOTE: Do not charge by means of an engine generator or DC power source. Use only 120V AC.

1.Plug the charger into any standard 120 Volt 60 Hz electrical outlet.

2.Slide the charger onto the battery pack as shown in Figure A and let it charge initially for 9 hours. After the initial charge, under normal usage, your power pack should be fully charged in 3 to 9 hours.

3.Remove pack from the charger and place in tool. NOTE: To remove the battery from the saw, press down on the release button on the back of the battery (Figure B) and pull out.

AB

IMPORTANT CHARGING NOTES

1.After normal usage, your power pack should be fully charged in 3 hours or less. If the power pack is run-down completely, it may take up to 9 hours to become fully charged. Your power pack was sent from the factory in an uncharged condition. Before attempting to use it, it must be charged for at least 9 hours.

2.DO NOT charge the power pack in an air temperature below 40°F or above 105°F. This is important and will prevent serious damage to the power pack. Longest life and best performance can be obtained if the power pack is charged when the air temperature is about 75°F.

3.While charging, the charger may hum and become warm to touch. This is a normal condition and does not indicate a problem.

4.If the power pack does not charge properly—(1) Check current at receptacle by plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. (3) Move charger and power pack to a surrounding air temperature of 40°F to 105°F. (4) If the receptacle and temperature are OK, and you do not get proper charging, take or send the power pack and charger to your local Black & Decker service center. See Tools Electric in yellow pages.

5.The power pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE using saw with its power pack in a depleted condition.

6.To prolong power pack life, avoid leaving the power pack on charge for more than 8 hours. Although overcharging is not a safety concern, it can significantly reduce overall power pack life.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents VEA EL Español EN LA Contraportada BDCSL1806 BDGCS1806Save this Manual for Future Reference Electrical Safety Personal SafetyWork Area Tool Use and CareService Causes and Operator Prevention of KickbackAdditional Safety Rules Circular Saws To Reduce the Risk of Kickback Safety Instructions Lasers BDCSL1806 onlyGuard Against Kickback Safety Guidelines Definitions Per minuteSafety Warnings and Instructions Charging Charging the Battery Important Charging NotesBattery CAP Information FIG. C Overview Figure D 11a13a Cutting Depth Adjustment Figures I & J Bevel Angle Adjustment Figure KAttaching and Removing the Blade Figure L, L1 Shoe Adjustment for 90 CutsOperating Instructions General Cuts Switch Installing the Batteries Figure NOperating the Laser BDCSL1806 only Automatic Electric BrakeSawing Operation Accessories Abrasive Type or Metal Cutting Blades on SAWRbrc Seal Service InformationFull TWO-YEAR Home USE Warranty Guide D’UTILISATION Conserver CE Manuel Pour UN Usage UltérieurConserver CES Mesures Zone DE Travail Sécurité PersonnelleUtilisation ET Entretien DE L’OUTIL Mesures DE Sécurité Relatives À L’ÉLECTRICITÉMesures DE Sécurité Spécifiques EntretienMesures DE Sécurité Additionnelles Scies circulaires Cause de rebonds et mesures de préventionLa scie ce qui favorise la torsion de la lame Mesures de précaution contre les rebondsMesures Pour Minimiser LES Risques DE Rebonds BD Circ Saws 5/30/08 1011 AM Lignes Directrices EN Matière DE Sécurité Définitions La minuteAvertissements de sécurité et directives chargement Charge DE BatterieRemarques Importantes DE Chargement Information Concernant LE Capuchon DU BLOC-PILE FIG. C Avertissement S’assurer, auWron g 13a Préparation pour l’assemblage et le réglage Réglage DE L’ANGLE DE Biseau Figure KFonctionnement Coupes GénéralesRéglage DE LA Semelle Pour LES Coupes DE SE Protéger DES Effets DE RebondFrein Électrique Automatique Utilisation DU Laser BDCSL1806 SeulementDétente Laser Intégré Mise EN MARCHE/ARRÊT DU LaserRetirer LE BLOC-PILES DE LA Scie Avant DE Régler LE Laser Pour Utiliser LE Trait LaserAccessoires Opérations DE SciageDécoupe EN Poche Figure Q DE Matières Abrasives Avec LA ScieDépannage Information SUR LES RéparationsCaractéristiques Techniques DU Laser Manual DE Instrucciones Conserve Este Manual Para Futuras ConsultasReglas Generales DE Seguridad Conserve Estas InstruccionesArea de trabajo Seguridad PersonalServicio Reglas DE Seguridad EspecificasReglas DE Seguridad Adicionales Sierras Circulares Causas DEL Contragolpe Y Prevención POR Parte DEL OperadorPara Reducir EL Riesgo DE Contragolpe Protéjase contra el ContragolpeLos que promueve que el disco cambie de dirección Instrucciones DE Seguridad Para EL Láser BDCSL1806 Solamente Pautas DE SEGURIDAD/DEFINICIONES Minutos Corriente alterna Corriente directaConstrucción clase Terminales de Conexión a tierre Revoluciones oCarga DE LA Batería Instrucciones y advertencias de seguridad cargaUtilice un solo cargador cuando carga Información Acerca DEL Protector DE LA Batería FIG. C Notas Importantes Sobre LA CargaDescripción DE LAS Funciones Figura D Mango principal13a 2726 Instrucciones DE Operación Cortes GeneralesRegulación DEL Ángulo DE Bisel Figura K Ajuste DE LA Zapata Para Cortes DEColocación Y Remoción DE LA Hoja Figuras L Y L1 InterruptorFreno Eléctrico Automático Apague y encienda la sierra cuatro o cinco vecesApagado Y Encendido DEL Láser USO DEL Láser BDCSL1806 SolamenteLáser Incorporado EN LA Unidad Cortes Internos Figura Q Para Usar LA Línea LáserOperación DE Corte Accesorios EL Sello Rbrc CULIACAN, SIN MEXICO, D.FMERIDA, YUC MONTERREY, N.LBD Circ Saws 5/30/08 1011 AM

BDCS1807, BDGCS1806, BDCSL1806, BDCS1806, BDCS2406 specifications

Black & Decker has long been recognized for its high-quality tools, and the models 90537965, BDCS1806, BDCSL1806, BDCS2406, and BDGCS1806 exemplify the brand's commitment to innovation and user-friendly design. These cordless tools are ideal for both amateur handymen and seasoned professionals, delivering efficiency and convenience.

The Black & Decker 90537965 features a robust design, with a focus on power and durability. It offers a lithium-ion battery that ensures a longer runtime, making it perfect for extended tasks without the worry of running out of power. Its compact size allows for easy maneuverability in tight spaces, making it an essential tool for any toolbox.

The BDCS1806 is a versatile cordless screwdriver that makes light work of DIY projects. It is equipped with an ergonomic handle that enhances comfort during extended use. The forward and reverse switch allows for easy operation, while the built-in LED work light illuminates dark areas, ensuring precision even in low-light conditions. With a lightweight design, it reduces user fatigue while providing substantial power for various applications.

Next, the BDCSL1806 adds another layer of versatility with its variable speed settings. This feature allows users to adjust the speed for different tasks, ensuring optimal control whether driving screws or removing them. The battery charge indicator keeps the user informed of remaining power, minimizing downtime.

For those looking for a more powerful option, the BDCS2406 stands out with its heavy-duty capabilities. This model boasts increased torque, making it ideal for tougher materials. It also includes a quick-change chuck, enabling rapid bit changes without the need for additional tools, thereby enhancing productivity.

Finally, the BDGCS1806 is a game-changer with its innovative design. It integrates a compact and lightweight structure that does not compromise on performance. Like its counterparts, it features a lithium-ion battery that provides exceptional longevity and consistent power delivery.

In summary, Black & Decker's 90537965, BDCS1806, BDCSL1806, BDCS2406, and BDGCS1806 models combine cutting-edge technology with user-centric design. Their exceptional features, such as ergonomic handles, variable speed settings, and powerful lithium-ion batteries, make these tools indispensable for anyone seeking reliability and performance in their tool collection.
Top Page Image Contents