Black & Decker BDCS2406, 90537965, BDCS1806, BDCS1807 Additional Safety Rules Circular Saws

Page 4

90537965 BD Circ Saws 5/30/08 10:11 AM Page 4

•When blade is binding or when interrupting a cut for any reason, release the trigger and hold the saw motionless in the material until the blade comes to a complete stop. Never attempt to remove the saw from the work or pull the saw backward while the blade is in motion or KICKBACK may occur. Investigate and take corrective actions to eliminate the cause of blade binding.

•When restarting a saw in the workpiece, center the saw blade in the kerf and check that teeth are not engaged into the material. If saw blade is binding it may walk up or KICKBACK from the workpiece as the saw is restarted.

•Support large panels to minimize the risk of blade pinching and KICKBACK. Large panels tend to sag under their own weight. Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel.

•Do not use dull or damaged blade. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and KICKBACK.

•Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and

KICKBACK.

•Use extra caution when making a "Pocket Cut" into existing walls or other blind areas. The protruding blade may cut objects that can cause KICKBACK.

Additional Safety Rules: Circular Saws

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

•lead from lead-based paints,

•crystalline silica from bricks and cement and other masonry products, and

•arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.

CAUTION: Wear appropriate hearing protection during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss.

•Snagging the lower guard on a surface below the material being cut can momentarily reduce operator control. The saw can lift partially out of the cut increasing the chance of blade twist. Ensure there is sufficient clearance under the workpiece.

•When necessary to raise lower guard manually, use the retracting lever.

•KEEP THE BLADES CLEAN AND SHARP. Sharp blades minimize stalling and kickback. The use of dull and/or dirty blades can increase the saw loading causing the operator to push harder which promotes twisting.

DANGER: KEEP HANDS AWAY FROM CUTTING AREA. Keep hands away from blades. Never place hands in front of or behind the path of the blade while cutting. Do not reach underneath work while blade is rotating. Do not attempt to remove cut material when blade is moving.

•SUPPORT LARGE PANELS. Large panels must be supported as shown (Fig. E & F) in this manual to minimize the risk of blade pinching and kickback. When cutting operation requires the resting of the saw on the workpiece, the saw shall be rested on the larger portion and the smaller piece cut off.

•USE ONLY CORRECT BLADES AND BLADE ASSEMBLY COMPONENTS WHEN MOUNTING BLADES. Do not use blades with incorrect size holes. Never use defective or incorrect blade washers or bolts. Follow blade assembly procedures.

•ADJUSTMENTS. Before cutting be sure depth and bevel adjustments are tight.

•SUPPORT AND SECURE THE WORK PROPERLY. Insure that the material to be cut is clamped (Fig. G) and solidly supported and balanced on a strong, stable and level work surface. Support the work so that the wide portion of the saw shoe is on the portion of the material that doesn’t fall after the cut is made. Never hold cut off piece by hand (Fig. H).

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Save this Manual for Future Reference BDCSL1806 BDGCS1806VEA EL Español EN LA Contraportada Electrical Safety Personal SafetyWork Area Tool Use and CareService Causes and Operator Prevention of KickbackAdditional Safety Rules Circular Saws Guard Against Kickback Safety Instructions Lasers BDCSL1806 onlyTo Reduce the Risk of Kickback Safety Guidelines Definitions Per minuteSafety Warnings and Instructions Charging Charging the Battery Important Charging NotesBattery CAP Information FIG. C Overview Figure D 11a13a Cutting Depth Adjustment Figures I & J Bevel Angle Adjustment Figure KOperating Instructions General Cuts Shoe Adjustment for 90 CutsAttaching and Removing the Blade Figure L, L1 Switch Installing the Batteries Figure NOperating the Laser BDCSL1806 only Automatic Electric BrakeSawing Operation Accessories Abrasive Type or Metal Cutting Blades on SAWFull TWO-YEAR Home USE Warranty Service InformationRbrc Seal Guide D’UTILISATION Conserver CE Manuel Pour UN Usage UltérieurConserver CES Mesures Zone DE Travail Sécurité PersonnelleUtilisation ET Entretien DE L’OUTIL Mesures DE Sécurité Relatives À L’ÉLECTRICITÉMesures DE Sécurité Spécifiques EntretienMesures DE Sécurité Additionnelles Scies circulaires Cause de rebonds et mesures de préventionMesures Pour Minimiser LES Risques DE Rebonds Mesures de précaution contre les rebondsLa scie ce qui favorise la torsion de la lame BD Circ Saws 5/30/08 1011 AM Lignes Directrices EN Matière DE Sécurité Définitions La minuteAvertissements de sécurité et directives chargement Charge DE BatterieRemarques Importantes DE Chargement Information Concernant LE Capuchon DU BLOC-PILE FIG. C Avertissement S’assurer, auWron g 13a Préparation pour l’assemblage et le réglage Réglage DE L’ANGLE DE Biseau Figure KFonctionnement Coupes GénéralesRéglage DE LA Semelle Pour LES Coupes DE SE Protéger DES Effets DE RebondDétente Utilisation DU Laser BDCSL1806 SeulementFrein Électrique Automatique Laser Intégré Mise EN MARCHE/ARRÊT DU LaserRetirer LE BLOC-PILES DE LA Scie Avant DE Régler LE Laser Pour Utiliser LE Trait LaserAccessoires Opérations DE SciageDécoupe EN Poche Figure Q DE Matières Abrasives Avec LA ScieDépannage Information SUR LES RéparationsCaractéristiques Techniques DU Laser Manual DE Instrucciones Conserve Este Manual Para Futuras ConsultasReglas Generales DE Seguridad Conserve Estas InstruccionesArea de trabajo Seguridad PersonalServicio Reglas DE Seguridad EspecificasReglas DE Seguridad Adicionales Sierras Circulares Causas DEL Contragolpe Y Prevención POR Parte DEL OperadorLos que promueve que el disco cambie de dirección Protéjase contra el ContragolpePara Reducir EL Riesgo DE Contragolpe Instrucciones DE Seguridad Para EL Láser BDCSL1806 Solamente Pautas DE SEGURIDAD/DEFINICIONES Minutos Corriente alterna Corriente directaConstrucción clase Terminales de Conexión a tierre Revoluciones oUtilice un solo cargador cuando carga Instrucciones y advertencias de seguridad cargaCarga DE LA Batería Información Acerca DEL Protector DE LA Batería FIG. C Notas Importantes Sobre LA CargaDescripción DE LAS Funciones Figura D Mango principal13a 2726 Instrucciones DE Operación Cortes GeneralesRegulación DEL Ángulo DE Bisel Figura K Ajuste DE LA Zapata Para Cortes DEColocación Y Remoción DE LA Hoja Figuras L Y L1 InterruptorFreno Eléctrico Automático Apague y encienda la sierra cuatro o cinco vecesLáser Incorporado EN LA Unidad USO DEL Láser BDCSL1806 SolamenteApagado Y Encendido DEL Láser Operación DE Corte Para Usar LA Línea LáserCortes Internos Figura Q Accesorios EL Sello Rbrc CULIACAN, SIN MEXICO, D.FMERIDA, YUC MONTERREY, N.LBD Circ Saws 5/30/08 1011 AM

BDCS1807, BDGCS1806, BDCSL1806, BDCS1806, BDCS2406 specifications

Black & Decker has long been recognized for its high-quality tools, and the models 90537965, BDCS1806, BDCSL1806, BDCS2406, and BDGCS1806 exemplify the brand's commitment to innovation and user-friendly design. These cordless tools are ideal for both amateur handymen and seasoned professionals, delivering efficiency and convenience.

The Black & Decker 90537965 features a robust design, with a focus on power and durability. It offers a lithium-ion battery that ensures a longer runtime, making it perfect for extended tasks without the worry of running out of power. Its compact size allows for easy maneuverability in tight spaces, making it an essential tool for any toolbox.

The BDCS1806 is a versatile cordless screwdriver that makes light work of DIY projects. It is equipped with an ergonomic handle that enhances comfort during extended use. The forward and reverse switch allows for easy operation, while the built-in LED work light illuminates dark areas, ensuring precision even in low-light conditions. With a lightweight design, it reduces user fatigue while providing substantial power for various applications.

Next, the BDCSL1806 adds another layer of versatility with its variable speed settings. This feature allows users to adjust the speed for different tasks, ensuring optimal control whether driving screws or removing them. The battery charge indicator keeps the user informed of remaining power, minimizing downtime.

For those looking for a more powerful option, the BDCS2406 stands out with its heavy-duty capabilities. This model boasts increased torque, making it ideal for tougher materials. It also includes a quick-change chuck, enabling rapid bit changes without the need for additional tools, thereby enhancing productivity.

Finally, the BDGCS1806 is a game-changer with its innovative design. It integrates a compact and lightweight structure that does not compromise on performance. Like its counterparts, it features a lithium-ion battery that provides exceptional longevity and consistent power delivery.

In summary, Black & Decker's 90537965, BDCS1806, BDCSL1806, BDCS2406, and BDGCS1806 models combine cutting-edge technology with user-centric design. Their exceptional features, such as ergonomic handles, variable speed settings, and powerful lithium-ion batteries, make these tools indispensable for anyone seeking reliability and performance in their tool collection.
Top Page Image Contents