Black & Decker BDCS1807 Operating the Laser BDCSL1806 only, Switch, Automatic Electric Brake

Page 14

90537965 BD Circ Saws 5/30/08 10:11 AM Page 14

SWITCH

Saw is equipped with a switch lock-off feature to prevent unintentional running.

•To operate the tool, press in on the lock-off button (2) from either side of the saw and hold it in as you depress the trigger switch (1).

•After you have depressed the trigger and the tool is running, release the lock-off button. The tool will continue to run as long as the trigger is depressed.

•To turn the tool off, release the trigger switch.

NOTE: This tool has no provision for locking the tool on, and the switch should never be locked on by any other means.

AUTOMATIC ELECTRIC BRAKE

Your saw is equipped with an electric blade brake which stops the saw blade within 1-1/2 seconds of trigger release. This is automatic and requires no adjustment.

Occasionally, under certain conditions, the brake will not function properly and won’t stop the saw in the 1-1/2 seconds as discussed above. If this condition occurs:

•Turn the saw on and off four or five times.

•If the problem still persists, have the tool serviced at a Black & Decker service center or company authorized service facility.

OPERATING THE LASER - (BDCSL1806 ONLY)

INSTALLING THE BATTERIES - FIGURE N

WARNING: LASER RADIATION. BE CERTAIN THE LASER ON/OFF BUTTON IS IN THE OFF POSITION (SEE SECTION “SWITCHING THE LASER ON AND OFF) BEFORE INSTALLING BATTERIES.

Lift the battery door (25) off the laser module (4) by gently squeezing the front of the door as shown in figure N. Insert 2 fresh 1.5 volt AAA batteries making sure to match (+) and (-) terminals correctly. Reattach the battery door.

WARNING: Batteries can explode, or leak, and can cause injury or fire. To reduce this risk:

•Carefully follow all instructions and warnings on the battery label and package.

•Always insert batteries correctly with regard to polarity (+ and -), marked on the battery and the equipment.

•Do not short battery terminals.

•Do not charge batteries.

•Do not mix old and new batteries. Replace all of them at the same time with new batteries of the same brand and type.

•Remove dead batteries immediately and dispose of per local codes.

•Do not dispose of batteries in fire.

•Keep batteries out of reach of children.

•Remove batteries if the device will not be used for several months.

“Transporting batteries can possibly cause fires if the battery terminals inadvertently come in contact with conductive materials such as keys, coins, hand tools and the like. The US Department of Transportation Hazardous Material Regulations (HMR) actually prohibit transporting batteries in commerce or on airplanes (i.e. packed in suitcases and carryon luggage) UNLESS they are properly protected from short circuits. So when transporting individual batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit.”

ON BOARD LASER

Your saw is equipped with an on board laser which is turned on and off separately from the saw.

WARNING: LASER RADIATION. Never aim the beam at a workpiece with a reflective surface. Bright shiny reflective sheet steel or similar reflective surfaces are not recommended for laser use. Reflective surfaces could direct the beam back toward the operator.

DANGER: LASER RADIATION. AVOID DIRECT EYE EXPOSURE. Do not stare into the laser light source. Never aim light at another person or object other than the workpiece. Laser light can damage your eyes.

WARNING: DO NOT use tinted glasses to enhance the laser light. Tinted glasses will reduce overall vision for the application and interfere with the normal operation of the tool.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents VEA EL Español EN LA Contraportada BDCSL1806 BDGCS1806Save this Manual for Future Reference Work Area Electrical SafetyPersonal Safety Tool Use and CareService Causes and Operator Prevention of KickbackAdditional Safety Rules Circular Saws To Reduce the Risk of Kickback Safety Instructions Lasers BDCSL1806 onlyGuard Against Kickback Safety Guidelines Definitions Per minuteSafety Warnings and Instructions Charging Charging the Battery Important Charging NotesBattery CAP Information FIG. C Overview Figure D 11a13a Cutting Depth Adjustment Figures I & J Bevel Angle Adjustment Figure KAttaching and Removing the Blade Figure L, L1 Shoe Adjustment for 90 CutsOperating Instructions General Cuts Operating the Laser BDCSL1806 only SwitchInstalling the Batteries Figure N Automatic Electric BrakeSawing Operation Accessories Abrasive Type or Metal Cutting Blades on SAWRbrc Seal Service InformationFull TWO-YEAR Home USE Warranty Guide D’UTILISATION Conserver CE Manuel Pour UN Usage UltérieurUtilisation ET Entretien DE L’OUTIL Conserver CES Mesures Zone DE TravailSécurité Personnelle Mesures DE Sécurité Relatives À L’ÉLECTRICITÉMesures DE Sécurité Spécifiques EntretienMesures DE Sécurité Additionnelles Scies circulaires Cause de rebonds et mesures de préventionLa scie ce qui favorise la torsion de la lame Mesures de précaution contre les rebondsMesures Pour Minimiser LES Risques DE Rebonds BD Circ Saws 5/30/08 1011 AM Lignes Directrices EN Matière DE Sécurité Définitions La minuteAvertissements de sécurité et directives chargement Charge DE BatterieRemarques Importantes DE Chargement Information Concernant LE Capuchon DU BLOC-PILE FIG. C Avertissement S’assurer, auWron g 13a Préparation pour l’assemblage et le réglage Réglage DE L’ANGLE DE Biseau Figure KRéglage DE LA Semelle Pour LES Coupes DE FonctionnementCoupes Générales SE Protéger DES Effets DE RebondFrein Électrique Automatique Utilisation DU Laser BDCSL1806 SeulementDétente Retirer LE BLOC-PILES DE LA Scie Avant DE Régler LE Laser Laser IntégréMise EN MARCHE/ARRÊT DU Laser Pour Utiliser LE Trait LaserDécoupe EN Poche Figure Q AccessoiresOpérations DE Sciage DE Matières Abrasives Avec LA ScieDépannage Information SUR LES RéparationsCaractéristiques Techniques DU Laser Manual DE Instrucciones Conserve Este Manual Para Futuras ConsultasArea de trabajo Reglas Generales DE SeguridadConserve Estas Instrucciones Seguridad PersonalServicio Reglas DE Seguridad EspecificasReglas DE Seguridad Adicionales Sierras Circulares Causas DEL Contragolpe Y Prevención POR Parte DEL OperadorPara Reducir EL Riesgo DE Contragolpe Protéjase contra el ContragolpeLos que promueve que el disco cambie de dirección Instrucciones DE Seguridad Para EL Láser BDCSL1806 Solamente Construcción clase Terminales de Conexión a tierre Pautas DE SEGURIDAD/DEFINICIONESMinutos Corriente alterna Corriente directa Revoluciones oCarga DE LA Batería Instrucciones y advertencias de seguridad cargaUtilice un solo cargador cuando carga Información Acerca DEL Protector DE LA Batería FIG. C Notas Importantes Sobre LA CargaDescripción DE LAS Funciones Figura D Mango principal13a 2726 Regulación DEL Ángulo DE Bisel Figura K Instrucciones DE OperaciónCortes Generales Ajuste DE LA Zapata Para Cortes DEFreno Eléctrico Automático Colocación Y Remoción DE LA Hoja Figuras L Y L1Interruptor Apague y encienda la sierra cuatro o cinco vecesApagado Y Encendido DEL Láser USO DEL Láser BDCSL1806 SolamenteLáser Incorporado EN LA Unidad Cortes Internos Figura Q Para Usar LA Línea LáserOperación DE Corte Accesorios EL Sello Rbrc MERIDA, YUC CULIACAN, SINMEXICO, D.F MONTERREY, N.LBD Circ Saws 5/30/08 1011 AM

BDCS1807, BDGCS1806, BDCSL1806, BDCS1806, BDCS2406 specifications

Black & Decker has long been recognized for its high-quality tools, and the models 90537965, BDCS1806, BDCSL1806, BDCS2406, and BDGCS1806 exemplify the brand's commitment to innovation and user-friendly design. These cordless tools are ideal for both amateur handymen and seasoned professionals, delivering efficiency and convenience.

The Black & Decker 90537965 features a robust design, with a focus on power and durability. It offers a lithium-ion battery that ensures a longer runtime, making it perfect for extended tasks without the worry of running out of power. Its compact size allows for easy maneuverability in tight spaces, making it an essential tool for any toolbox.

The BDCS1806 is a versatile cordless screwdriver that makes light work of DIY projects. It is equipped with an ergonomic handle that enhances comfort during extended use. The forward and reverse switch allows for easy operation, while the built-in LED work light illuminates dark areas, ensuring precision even in low-light conditions. With a lightweight design, it reduces user fatigue while providing substantial power for various applications.

Next, the BDCSL1806 adds another layer of versatility with its variable speed settings. This feature allows users to adjust the speed for different tasks, ensuring optimal control whether driving screws or removing them. The battery charge indicator keeps the user informed of remaining power, minimizing downtime.

For those looking for a more powerful option, the BDCS2406 stands out with its heavy-duty capabilities. This model boasts increased torque, making it ideal for tougher materials. It also includes a quick-change chuck, enabling rapid bit changes without the need for additional tools, thereby enhancing productivity.

Finally, the BDGCS1806 is a game-changer with its innovative design. It integrates a compact and lightweight structure that does not compromise on performance. Like its counterparts, it features a lithium-ion battery that provides exceptional longevity and consistent power delivery.

In summary, Black & Decker's 90537965, BDCS1806, BDCSL1806, BDCS2406, and BDGCS1806 models combine cutting-edge technology with user-centric design. Their exceptional features, such as ergonomic handles, variable speed settings, and powerful lithium-ion batteries, make these tools indispensable for anyone seeking reliability and performance in their tool collection.
Top Page Image Contents