Assembly, Inserting the Plunger Rod

ASSEMBLY

WARNING!

Always lock trigger or remove battery pack before changing or removing acces- sories. Only use accessories speciﬁcally recommended for this tool. Others may be hazardous.

Installing Tube Holder Assembly (Cat. No. 6562-23) (Fig. 4)

Fig. 4	Plunger rod	6562-23
	Washer (black)	6562-23
	Washer (black)
		Washer (Steel)
		Barrel nut
		Plunger
		Screw

Inserting the Plunger Rod

Always lock the trigger or remove the battery pack before inserting the plunger rod. Do not run the tool to pull the plunger rod through

3. Insert the plunger rod from the rear of

the tool. It may be necessary to wiggle

the plunger rod slightly while pushing it

Tube holder

the tool, this will damage the tool and rod. Manually push the plunger rod through the tool, as follows:

1.Press in and hold rod release trigger.

2.Grasp the plunger rod handle. The teeth on the plunger rod should point toward the left and slightly down.

through the tool.

NOTE: Keep the plunger rod clean. Retract- ing or inserting a plunger that is covered with material may damage the internal parts of the tool.

1.	Lock trigger or remove battery pack.
2.	Press in and hold rod release trigger.
3.	Grasp plunger rod handle and pull
	plunger rod back until the rod tip is just
	inside of tool.
4.	Release rod release trigger.
5.	Position washer (black) onto nose of
	tool. The side with the larger collar ﬁts
	inside the tool.

7.	Place washer (steel) between the tube
	holder and barrel nut. Thread barrel nut
	into nose of the tool. Tighten securely
	using the wrench provided.
8.	Press rod release trigger and push
	plunger rod forward to access the tip of
	the rod.
9.	Attach plunger to the plunger rod, as
	shown (Fig. 4). Tighten the screw se-
	curely.

Installing 10oz Tube Holder Assembly (Cat. No. 6562-21) (Fig. 3)

Fig. 3	Plunger rod	Plunger
		Screw
Tube holder
Barrel nut
Frame cap	Tube holder	6562-21
Frame cap		6562-21

6. Install tube holder over washer.

10. To remove tube holder, reverse proce-

WARNING!

To reduce the risk of injury, keep hands out of the plunger area of the tool. Fingers can be pinched between the tube holder and the plunger.

Installing Caulk or Adhesive Tube

1.Lock trigger or remove battery pack.

2.Press in and hold rod release trigger.

3.Grasp plunger rod handle and pull plunger rod back until the rod tip is just inside of tool.

4.Release rod release trigger.

5.The frame cap, barrel nut, and tube holder are provided pre-assembled.

6.Thread barrel nut into the nose of the tool. Tighten securely using the wrench provided.

7.Press rod release trigger and push plunger rod forward to access the tip of the rod.

8.Attach plunger to the plunger rod, as shown (Fig. 3). Tighten the screw se- curely.

9.To remove tube holder, reverse proce- dure.

1.Lock trigger or remove battery pack.

2.Cut nozzle of tube at an angle and size per manufacturer's recommendation to suit the job. A smaller nozzle diameter requires more force to push the caulk and reduces battery life.

3.Break inner seal of tube using a long nail or piece of wire. If the inner seal is not broken, the caulk material may be forced out the rear end of the tube and damage the tool.

NOTE: Before using a partially ﬁlled tube, remove any hardened material with a long nail or piece of wire.

4.Press in and hold rod release trigger.

5.Grasp plunger rod handle and pull plunger rod back to allow the caulk tube to ﬁt inside carriage frame.

6.Insert caulk tube into carriage frame.

7.Push plunger rod handle forward until the plunger is against the caulk tube.

8.Release rod release trigger.